Question about 1993 Oldsmobile Cutlass Supreme

Open Question

I have a 93 olds cutlass supreme my break lights will not turn on and i replaced the fuses and my break light switch the wireing works and everthing is fine but my light do not turn on they turn on sometimes like once in a blue moon any sugguestion on what it may be??

Posted by on

  • Ramiro Camarillo
    Ramiro Camarillo Nov 23, 2013

    joseph If I turn my blinker on it works but if I don't It wont work

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: Both turn signals light, but do not blink

under the dash on the driver side there is a round or square sliver box that should say turn signal or flasher on it in the fuse box.

Posted on Feb 26, 2009

Ad
  • 1 Answer

SOURCE: I need to locate and replace the multi function switch

My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Posted on Mar 22, 2009

  • 2 Answers

SOURCE: changing turn signal switch on 93 oldsmobile cutlass supreme

Removing the turn signal mechanism from the steering column is easy and can be accomplished in under a half hour. First you should remove one of the battery cables as you should have no power available when removing or installing the wiring harness.then remove the front of the steering wheel.These usually just snap on or off. Remoce the steering wheel using a small puller once you have removed the nut. . Usually available for aroung $10. Now that the signal mechanism is exposed you can wemove the plastic horn ring and also the 3 screws securing the mechanism to the steering column. Leave the mechanism on the colum for now. You can however reomove the screw that holds the lights, wiper and turn signal arm and let it hang free as there is no need to replace it if everything is working. Next you have to remove the two panesl under the dash immediately under the steering column. Tracing the wiring from the turn signal to where it enters a wiring block. This block has all the wiring from the turn signal, lights , cruise control and turn signals all on different modules. You are only concerned with the module from your tirn signals. To remove this module you have to separate the block by using a small ratchet and a 7mm socket. once the the bolt holdingb the block has been completely loosened the inner block can be oulled away from the outer block. Now the module containg the turn signal harness can be removed from the inner blosk and now you are close to removing the harness but first there is a plastic sleeve that protest the wiring as it passes along the lower part of the colimn. Squeezing one end of the sleeve you can push it out until it clears the colum. it can now be opened and reomoved from the harness. Now you can reomve the mechanism from the column and ease the harness up throught the steering solumn being careful to guide it through. The last two wires on the module , a beize and green wire that ties internally to the column will need to be cut and spliced into the new harness. Using the reverse proceedure you can install the new turn signal. First time may take a hour or so . One gets better with practice. Good luck John

Posted on Jun 08, 2009

dburns60
  • 410 Answers

SOURCE: I need to replace turn signal switch on 97 olds cutlass supreme.

Disconnect the battery to do any service on the steering column or front radiator areas.

Posted on Jun 30, 2009

Shorty1_wt
  • 324 Answers

SOURCE: i have a 1997 olds cutlass supreme and have no brk lites

sounds like a bad or loose ground wire, it would be located in the trunk near the tail light assembly, the other switch is for the cruise contro, it's what cuts the cruise when you hit the brakes.

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights and Turn Signals not working on 1992 Cutlass Supreme


Check for voltage to the light socket, if its low its probably a corroded wire or a short. If nothing try it at the fuse. It could also be the flasher unit or in the steering column. Since this was followed by the brake lights not working I would suspect something in the wiring, good chance of a bad ground. Bad grounds can send you in circles trying to diagnose elect. problems.

Nov 07, 2013 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Tail lights don't work on 83 cutlass supreme


I assume you checked the bulbs and they were good? It's possible that the sockets have gone bad and need replacing. The tail lights are fused through the instrument panel lights. that fuse should be in the middle of your fuse box, marked "instr". If the fuse is good check to see if the dash lights come on when you turn the headlight switch on. If they don't then change the headlight switch. hope this helps.

Mar 12, 2012 | 1983 Oldsmobile Cutlass Supreme

2 Answers

Brake and turn signals not working


usually this indicates that the brake light switch or turn signal or flasher have failed.i would start by replacing the brake light switch located on the upper area of brake pedal and fix ya problem. 

Jul 12, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Have a 96 Olds Cutlass Supreme, brake lights will not work. We've replaced bulbs, fuses and brake light switch and still nothing. Help!


Try having someone push on brake pedal at the same time thay move the turn signal lever up and down slightly to see if your brake lights work this would tell me that you have a faulty turn signal switch because GM runs the brake lights thru the turn signal switch so they work if you are driving with your 4way flashers on.

Jun 06, 2010 | 1996 Oldsmobile Cutlass Supreme Coupe

2 Answers

Car will not start


i am having same issue with a 1994 oldsmobile cultlass supreme and i was told bye 4 different ase mechanic that the ignition swith in steering column is bad.the wires are hair fine and when you start the car the wires turn breaking them.i am going to replace the ones in my daughters car and pray for the best.jgoofy4life@yahoo.com

Jan 05, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

1995 cutlass supreme HELP


You'll need to replace the turn signal switch. I had the same problem a few years ago and replacing the TS switch made everything OK

Jun 30, 2008 | 1995 Oldsmobile Cutlass Supreme

2 Answers

Brake lights


5891018758910190Hope this helps. contact me if you need more help please give me a rating if you would.

Jun 13, 2008 | 1995 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1993 Oldsmobile Cutlass Supreme Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...