Question about 2002 Nissan Xterra

Open Question

Need picture location of temp coolant sensor 2004 nissan xterra

Where do I find the coolant temp. sensor on my Nissan xterra engine it have gone bad need to replace it.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: nissan xterra knock sensor

It's the valley of the engine underneath the intake manifold. It's about an $800 job because the top of the engine has to come off. However, unless you have a supercharged xterra it shouldn't effect performance. Also, the knock sensor will not trip the check engine light, as it does not indicate a primary problem, so if your light is on you should have another code that should be fixed first.

Posted on Nov 24, 2008

  • 63 Answers

SOURCE: Where is low pressure service port located on 2004

Near the compressor are two ports; one on a large tube leaving the compressor and one on a small tube. The one on the large tube is the low pressure side.

Posted on Jun 13, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

ZJLimited
  • 17970 Answers

SOURCE: Diagram available for 01 Nissan Xterra Knock Sensor location?

V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Posted on Feb 08, 2010

SOURCE: HOW TO REPLACE A FUEL PUMP FOR A NISSAN XTERRA


Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:

    Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump

To install:
  1. Install or connect the following:

    Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
  2. Fill the fuel tank.
  3. Start the engine and check for leaks.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the sensor located on a xterra truck it is a 2004


The cooling sensor is located on the intake , when you go to autozone for the replacement part ask for a diagran of its location.

Nov 23, 2013 | Nissan Cars & Trucks

1 Answer

Temperature gauge reading hot but engine not hot


Could be your coolant temperature sensor is bad,here's a link on how to replace,it's located near thermostat housing,you don't have to drain coolant.Here's what the sensor look's like.

Oct 30, 2013 | 2002 Nissan Xterra

2 Answers

Picture/location of crankshaft position sensor 2003 nissan exterra


The location is in back of the engine on the top of the transmission3_17_2012_9_03_53_pm.jpg

Mar 17, 2012 | 2003 Nissan Xterra

1 Answer

Are there 2 knock sensors on an 2004 nissan xterra 2 wd. V6 n were are they located


I have looked everywhere and also went to my 2 of my parts suppliers and there is only one knock sensor for your vehicle. Below are pictures right out of my Nissan Factory Service Manual and it does only list 1 knock sensor. If you have any questions or need any testing procedures feel free to email me at csautomotivecars@att.net. and I will send what I have.


clifford224_380.jpg

clifford224_382.jpg

Aug 26, 2011 | 2004 Nissan XTerra

1 Answer

Where is the coolant sensor located on a nissan sentra 2001 1.8 engin


I assume you are referring to the coolant temp sensor. as you look at the front pulleys of the engine, its on the right side behind a bracket just above the alternator. See picture below and let me know if you have questions. If you are referring to the coolant level sensor, it would be on the side of the coolant reservoir.

jturcotte_134.gif

Nov 09, 2010 | 2001 Nissan Sentra

3 Answers

Diagram available for 01 Nissan Xterra Knock Sensor location?


V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Feb 08, 2010 | 2001 Nissan Xterra

1 Answer

Where is the knock sensor for the 04 nissan xterra located?


Your knock sensor is located undernesth the air intake manifold on top of the engine block. This goes for 2000-2004 xterra V6 3.3L models.

Nov 05, 2009 | 2002 Nissan Xterra

3 Answers

2004 Nissan Maxima temp gauge fluctuation


well the temperature control gage is connected to the engine block and consists of 1 wire for the reading of the motor heat either the sensor is going bad or you need to check your coolant levels in the radiator make sure the engine is cool before opening the thermostat cap to the radiator so not to get burnt ...also make sure the wire itself is not grounding out on the engine block to give the gage to give such a readout look to the engine and usually on the drivers side lower the plug wires you should see a plug with a wire coming from it ensure the wire is not rubbing on anything .

Oct 02, 2009 | 2004 Nissan Maxima

Not finding what you are looking for?
2002 Nissan Xterra Logo

Related Topics:

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...