Question about 1992 Honda Accord

1 Answer

WHERE IS THE EGR VALVE SOLENOID AND THE EGR SENSOR LOCATED AT ON A 1992 HONDA ACCORD

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 818 Answers

Here is a good video-http://www.youtube.com/watch?v=7zyH9rviFdI hope this helps - cheers Denny

Posted on Nov 23, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: where is the o2 sensor located on a 1991 honda accord ex 2.2 engine

Further clarification on the O2 sensor location: It is in the exhaust pipe, under the center of the car, on top of the pipe, just aft of the oil filter.

Posted on Jul 14, 2008

  • 48 Answers

SOURCE: 2000 Honda Accord EGR Valve Error P0401

Jason,
-after you change the part you have to reset/clear the code

-this can be done by either:
(1) using the OBD2 code reader that Autozone used OR since option 2 (below) is very quick
(2) disconnecting the battery for about 30 seconds (this will delete all codes/radio presets/etc) but it will also clear the 'check engine' code
-this is what I do AFTER i write down my radio station presets :)

-hopefully the new EGR valve resolves your issue after you CLEAR the code
...but that code just means a an insufficient amount of Exhaust Gas recirculation (pressure difference) used to keep the emissions in check
-if it comes back, then there are a few other fixes to try also

-let me know if you need further assistance
-please remember to rate me `fix-ya`if it works
thanks

Posted on Nov 03, 2008

emissionwiz
  • 76649 Answers

SOURCE: 1992 Honda Accord will not pass emissions inspection

The EGR will not cause this issue, this sounds like the Catalytic Converter was not hot enough, another trick that worked for this kind of fail was a fresh oil change, make sure the engine is up to normal operating temp, which would be just short of 1/2 scale on the temp guage, if it runs cold replace the thermostat, I did smog tests for 30 years and these are the things I did to get cars like yours to pass given the test results you gave for the tailpipe.

Posted on Dec 05, 2008

  • 105 Answers

SOURCE: Where can I locate the O2 sensor on a 1992 Honda

the ex, lx, dx model are located on the exhaust manifold
the exr, special edition models are located on the down pipe by
the flex pipe

Posted on Oct 27, 2009

gh20s
  • 343 Answers

SOURCE: Need to locate PCV valve on 4cyl. Honda Accord

It should be on the valve cover. It should b "L" shaped and inserted into a rubber grommit and connected at the top is a vacuum line.

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No egr valve operation


The electrical vacuum switch, that regulates vacuum to the egr valve, is bad. Test and replace it if necessary.

Oct 04, 2012 | 1992 Honda Accord

1 Answer

When the egr valve is bad on a 1992 honda accord wagon what happens?


If it's stuck closed, you will feel no ill effects. If it's stuck open, the car will not idle right and be hard to start. If you're getting an egr trouble code from your accord, test the egr valve to make sure it's working; use your finger to push up on the egr valve diaphragm, while the car is idling....car should shake and shut off if the egr valve is good. The one vacuum solenoid that feeds the egr valve, on that generation accord, is known to go bad and cause the egr trouble code. Check that solenoid if the egr valve tests ok.

Sep 15, 2011 | 1992 Honda Accord

1 Answer

How to install speed sensor for Ford F 250 1992 truck


Disconnect the negative battery terminal. Disconnect the wiring connectors to the air cleaner, Mass Air Flow sensor, EGR vacuum solenoid, and DPFE sensor. Remove the air intake assembly (up to the throttle body). There are two vacuum lines from the EGR vacuum solenoid, find where they reach the EGR valve and the intake manifold, disconnect them at these points. There is a rubber hose coming from the firewall to the top of the engine, disconnect this and push it aside. Remove the nut directly below this hose (this nut holds the bracket that the DPFE and EGR vacuum solenoid are mounted to). Follow the mounting bracket around and remove the smaller nut holding it on. Have some tape ready to mark two hoses. Make a note of which hose is the "Hi" and "Ref" on the DPFE sensor and remove them. Remove the DPFE/EGR vacuum solenoid assembly. Congratulations, now you have access to the EGR valve!!

hoping help you

Jun 11, 2011 | 1992 Ford F250

1 Answer

My 1992 honda accord failed emissions just on oxide nitrogen the standard is 2.50 and mine was 2.52.what do i have to do to fix problem to make it pass.


Engine Temp?
Thermostat or Coolant sensor

Vacuum Leaks

Egr Valve

Ignition Misfires

Bad converter

O2 Sensors

Need to have the entire engine checked
for proper operation

Apr 06, 2011 | Honda Accord Cars & Trucks

2 Answers

1992 Honda Accord Ex stick shift. has been either not starting or cutting off after it starts. If I wait about 10 mins., it will start again. I have replaced the starter the heat sensor unit and new...


Check your main relay. It powers the fuel pump and the ignition system. They are a known problem, with a high failure rate, on the 90-93 accords. I do believe it's worth checking.

Nov 04, 2010 | 1992 Honda Accord

1 Answer

How to replace egr valve on 1995 crown vic 4.6. Valve is in hard place to get to.


On 1995 Crown Victoria the EGR valve is located at the rear of the engine compartment. While the attaching bolts can be gotten out with a little bit of a problem the egr tube that atteches the EGR valve to the right exhaust manifold is a pain. It is possible to do though. Here are the removal and installation instructions. If you are sure that the EGR valve is the reason for any check engine light then you can remove the battery cable for about five minutes to reset the light, but if the light is on for a differant reason then you just got rid of the code plus any freeze frame data that a shop could have used to diagnose the problem.

Check this procedure about REMOVAL & INSTALLATION...

PFED Sensor
See Figures 9, 10, 11 and 12


bcc2045.jpg
Fig. 9: Detach the connector for the DPFE sensor


78e8250.jpg
Fig. 10: Matchmark and remove the vacuum hoses for the DPFE sensor and ...


daae4e4.jpg
Fig. 11: ... remove the retaining nuts from the DPFE sensor and ...


b6fd561.jpg
Fig. 12: ... remove the DPFE sensor from the intake manifold
  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring harness from the DPFE sensor.
  3. Label and disconnect the vacuum hoses.
  4. Remove the mounting screws and remove the DPFE sensor.
To install:
  1. Position the DPFE sensor and tighten the mounting screws.
  2. Attach all necessary hoses and wiring to the sensor.
  3. Connect the negative battery cable.

EGR Valve Control Solenoid
See Figures 13 through 17


bb3e162.jpg
Fig. 13: Detach the connector for the EVR solenoid


a9fc1b4.jpg
Fig. 14: Match mark the vacuum hoses for the EVR solenoid and ...


57ba344.jpg
Fig. 15: ... remove the vacuum hoses from the EVR solenoid


f5d5cc2.jpg
Fig. 16: Remove the retaining nut for the solenoid and ...


4b98f79.jpg
Fig. 17: ... remove the solenoid from the intake manifold
  1. Disconnect the negative battery cable.
  2. Label and detach the vacuum hoses from the EVR solenoid.
  3. Detach the electrical connector from the solenoid.
  4. Remove the retaining hardware, and remove the solenoid.
To install:
  1. Position the solenoid and install the retaining hardware.
  2. Attach the main emission vacuum control connector and the wiring harness connector to the EVR solenoid.
  3. Connect the negative battery cable.

continue...

Jul 16, 2010 | 1992 Ford Crown Victoria

2 Answers

Abs light on accord 1992


ABS control unit recognizes system related problems and causes ABS warning light to come on and stay on under any of following conditions:
  • ABS pump runs longer than 2 minutes.
  • Vehicle is driven with parking brake on longer than 30 seconds.
  • One rear wheel is locked.
  • Wheel speed sensor does not transmit a signal.
  • Vehicle is driven on extremely rough road.
  • Low battery voltage.
  • Operation time of solenoid valves exceeds a specified value and control unit indicates an open circuit in solenoid circuit.
  • Output signals from control unit are not transmitted to solenoid valves.
  • Temporary loss of traction due to excessive cornering speed or starting from stuck condition (mud, snow or sand).

Nov 19, 2009 | 1992 Honda Accord

1 Answer

92 Honda Accord failing Emissions


look at oxygen sensor.look at egr control solenoid.

Apr 10, 2009 | 1992 Honda Accord

1 Answer

1992 Honda Accord will not pass emissions inspection


The EGR will not cause this issue, this sounds like the Catalytic Converter was not hot enough, another trick that worked for this kind of fail was a fresh oil change, make sure the engine is up to normal operating temp, which would be just short of 1/2 scale on the temp guage, if it runs cold replace the thermostat, I did smog tests for 30 years and these are the things I did to get cars like yours to pass given the test results you gave for the tailpipe.

Dec 03, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...