Question about Chevrolet Cars & Trucks

Open Question

2007 grand prix driver side front fender replacement

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

grease16
  • 58 Answers

SOURCE: 1998 Pontiac Grand Prix A/C Blows hot on drivers side coldeer on passenger

i have an Idea. first of all make sure that all of your vents are not plugged up. next check your heating coils to find out if only one side is hot or the other is only cold. i need more info

Posted on Jun 30, 2008

  • 3 Answers

SOURCE: Pontiac Grand Prix 98

When the window is not used often or gets a little older the motor can "Hang Up" You might try having someone hold the down switch on the drivers door while you slam the door. This will sometimes jar the motor enough to make the brushes contact and start working.

Posted on Oct 04, 2008

handybc70
  • 25 Answers

SOURCE: Front fender removal

Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

808b156.jpg

Posted on Jan 11, 2009

  • 159 Answers

SOURCE: Replacement Front, Driver Side Window Regulator

first these are easy to do,second look on ebay a-1 auto I think sells replacement for around $100 U.S
Take door panel off,there are several bolts in reg and 2 keepers on the window glass unhook the 2 keepers unplug the motor and turn unit and bring out the bottom of the doorthe window glass does NOT have to come out. it should only take less than an hour to do.

Posted on Sep 27, 2009

  • 2 Answers

SOURCE: How do I remove a wrecked front fender assy/quarter panel?

The front fenders are connected to the A pillar above the the top hinge, at the bottom of the rocker panel seam, three bolts pass through the hood hinge support in the middle of the fender, four bolts on the radiator support, three vertical bolts on the top radiator brace, and one bolt at the rear of the wheelhouse to the cab body. Yes, the wheelhouse is spot welded to the fender and must be removed with it. Remove all the bolts listed as well as the bolts retaining the splash shield. The splash shield is a plastic liner connected to both the wheelhouse and the fender. Remove the headlight/cornering lamp assembly. The best way I have found to do this is to loosen the bumper to framebrackets and let the bumper assembly sag to gain clearance. If the upper bumper cover is removed to gain the clearance needed you will more than likely need to get a new cover as the nylon clips have a tendency to break during removal. Once the fender/wheelhouse assembly has been removed use a spot weld cutter to separate the wheelhouse from the old fender. Check the new fender for clearance and fit on the vehicle. Make all the needed adjustments to get the fender to fit correctly. Remove the fender and attach the wheelhouse. This should be done by spot welding. It can also be done using bolts. If using bolts place some 3M double stick weather strip adhesive tape in the seam to prevent direct contact of the parts to prevent rattles and squeaks. Drill the new fender to match the holes made by the spot weld cutter in the wheelhouse. Use stainless bolts and lock nuts so that the assembly can be services if needed. I would also recommend using Wurth Rust Inhibitor on all the seams to prevent rust and once cured it is an excellent adhesive and will reduce noise coming from moving body panels. Good Luck. It is not as bad as it sounds. Take your time and it will be worth the effort.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Will a 2000 grand am GT front fender fit a 1999 grand Prix?


Nope, Grand Am and Grand Prix are two totally different platforms.

Feb 11, 2016 | Cars & Trucks

1 Answer

How to replace front left fender on a 02 pontiac grand. Prix


Best to start by removing the wheel, then the inner plastic fender...held on with plastic push up tabs...remove all under hood fender bolts...probably 13mm...compare your replacement fender to confirm all necessary bolts to be removed, Is your new fender already painted?

Dec 26, 2014 | 2002 Pontiac Grand Prix

1 Answer

Location of fuel filter in 2007 pontiac grand prix


rear of drivers side of car near gas tank

Mar 23, 2012 | 2007 Pontiac Grand Prix

1 Answer

Hron does not work, fuse ok 06 grand prix ,wher is the horn relay


Normally these are on the fender wells in the engine bay, underneath a plastic vanity cover. If I had to guess I would say the driver side. On the bottom side of that cover sometimes there will be a sticker location of the relays, because they will all be the same size and color.

Dec 01, 2011 | 2006 Pontiac Grand Prix

1 Answer

2007 Grand Prix GXP Sedan: where do u open the trunk...


press and hold the door open lever on the driver side door for a few seconds. Viola!!!

May 06, 2010 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

I need to remove and replace my drivers side door and do not know how to do so.


go look at the passengers side. take note of the door seam and fender seam width. its about the width of a piece of cardboad. additionally look at the door hinges on the passenger side. it may or may not have washer shims. if they do/dont then just match up with passenger side. it takes 2 people to hang the door. screw in door hinges "finger tight" just to take off the weight of someone holding the door. play with the hinges until you can open/close door without binding or crimping fender at the seam. do not over tighten hinge bolts until the door opens/closes unobstructed. bottomline 2 people needed. slow and tedious job. you may have to add or take shims(washers) out for good fit. note that you may have to add shims to the inner door hinges or to the fender hinges where they meet. hope this is clear instructions.

May 30, 2009 | 2002 Pontiac Grand Prix

1 Answer

I am removing the right front fender on a 96 pontiac grand prix


U NEED TO TAKE YOUR FINDERWELL OUT FRIST ON THAT SIDE THIN OPEN HOOD THE BOLTS R RIGHT AT THE TOP WERE YOUR HOOD FITS THE FINDER SHOULD BEE ABOUT SIX OR SO NOTE THE FINDER WELL IS THE UNDER NEATH PART OF YOUR FENDER U MAY WONNA REMOVE YOUR PARKING LIGHT FOR THAT SIDE JUST TO MAKE SURE U DONT BRAKE IT AND JUST BELOW THE MARKER LIGHT SHOULD BEE A FENDER BRACE REMOVE IT ALSO ITS LIKE A SHORT METTEL BAR ALL BOLTS SHOULD BEE 1/2 INCH GOOD LUCK AND RATE THIS PLEASE

Apr 05, 2009 | 1995 Pontiac Grand Prix

2 Answers

2001 grand prix starts and then dies right away


Check the fuel pump inline resistor located on the right side front fender between the frame and the windshield washer fluid canister. When this resistor goes bad those are the symptoms.

Apr 03, 2009 | 2000 Pontiac Grand Prix

1 Answer

Body work, pulling fenders off


Yep...see the link in the GP thread. The dude had to remove the hood bracket.

Thread bumper and fender removal

Jul 05, 2017 | 1997 Pontiac Grand Prix

2 Answers

1985 grand prix


the oil sending unit is located on the front of the engine(this is facing the passenger side fender.) to access it take the front tire off on passenger side you will see the oil filter and a sending unit right behind and above it it will have a green colored plug. please rate this. thanks

Sep 23, 2008 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...