Question about 1987 Oldsmobile Cutlass Supreme

Open Question

Where is the air blend door actuator located on a 1987 oldsmobile cutlass

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 71 Answers

SOURCE: Engine mount location for a 1987 Oldsmobile Cutlass Ciera

This is a 4 cyl transverse mounted engine, and it has 3 engine mounts one in front and one on the subframe in the backside of the block and another holds the transaxel. If you have some poping sounds when starting or hard shifing of the gears, then one or more may need replacing.

Posted on Jan 05, 2009

  • 548 Answers

SOURCE: 1991 oldsmobile cutlass Location of starter

Follow the red wire from the battery towards the firewall. It will end at the starter.

Posted on Feb 06, 2009

  • 5 Answers

SOURCE: 1999 Oldsmobile Cutlass Cigarette Lighter Fuse

Under the hood directly in front of the driver is a covered fuse block. Remove the cover and the fuse is #34.

Posted on Mar 08, 2009

  • 236 Answers

SOURCE: Where is the blend door actuator located? Is it a

buried in the dash, about an 8 hour job.

Posted on Oct 13, 2009

c17hydro
  • 2984 Answers

SOURCE: Where is the fuel pump on my 1987 Oldsmobile

If it's a carbureted motor it is right here:

e7b047f.gif
If it is fuel injected it is in your gas tank:

9e9629d.gif
The electric fuel pump has an in-tank design

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is rhe air temp. Door actuator in a 2003 ford 450 truck


Ford Superduty Erratic Temp Blend Door Actuator Removal - YouTube

? 12:29
https://www.youtube.com/watch?v=dYPOtin3JUk
Dec 1, 2013 - Uploaded by FordTechMakuloco
Only buy the Ford Actuators, you can get them cheaper here- ...

Simple how to fix blend door heater a/c actuator 2002 - 2008 ford ...

? 7:12
https://www.youtube.com/watch?v=EEWuJuhCtmc Aug 24, 2013 - Uploaded by kirk colombo
Simple how to fix blend door heater a/c actuator 2002 - 2008 ford explorer noise .... I literary just finish ...

08-10 Super Duty Blend Door Actuator Location - Dual System ...

? 1:24
https://www.youtube.com/watch?v=s7awF2fTKf4 Mar 22, 2012 - Uploaded by srmastertech
Here is a quick view showing the location of the temp blend door actuators on the Ford Super Duty's with ...

Ford blend door fix - 15 minutes - YouTube

? 3:22
https://www.youtube.com/watch?v=wsjGxreGlkA Jul 21, 2013 - Uploaded by SoonersWarriors
Ford blend door fix - 15 minutes. SoonersWarriors. Loading ... Ford Vehicles: Frequent Blend Door Actuator ...

Blend Door Actuator Ford Super Duty 08-10 - YouTube

? 9:45
https://www.youtube.com/watch?v=mbzjCPYENZQ Oct 4, 2013 - Uploaded by MostExcellentDude
This applies to 2008-2010 F250 and F350 with the dual climate control. This video shows the locations for the ...
blend door actuator 2003 ford f450 Google Search




Aug 16, 2017 | Ford Cars & Trucks

1 Answer

2000 oldsmobile bravada heater control valve location


If you are looking for some sort of water valve that diverts water to/from the heater core, forget it. They don't exist anymore. They went away shortly after the widely adapted use of air conditioning in today's modern cars. Now, hot coolant is routed thru the heater core at all times, but is controlled by a cable-operated, or vacuum operated "blend door" located inside the heater box. If you are not getting heat to the vehicle, there are a few possible problems:

1. Bad thermostat - thus low coolant temperature and lack of heat.
2. Clogged heater core - no water flow thru core, thus no heat.
3. Broken control head - loss of cable or vacuum actuation of blend door.
4. Broken heater box/vacuum tank - no actuation of blend door.

Of the items listed above, based on the age of the vehicle and the likelihood of occurrence, I would investigate them in the order of 2, 4, 1, 3.

Jan 20, 2016 | 2000 Oldsmobile Bravada

1 Answer

Where is drivers, mode door and blend door actuators located


Blend air door actuator (temp)on left side of heater box near the gas pedal below it may be the mode door & passenger side has a temp door actuator for that side.

Nov 21, 2015 | 2000 Dodge Caravan

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

1 Answer

No heat Heater core is hot


If heater core is getting coolant circulating through it then you may have a temp blend door, or blend door actuator not working properly. The blend door is located in the air box under the dash, and the actuator is located on the air box. You may be able to visually check the operation while turning the temp knob, by locating the coresponding actuator on the air box and monitoring the movement. If it is moving ok and still no heat then the blend door, or lever is broken, which will require removal of the dash.

Oct 17, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Where is the blend door actuator located? Is it a


buried in the dash, about an 8 hour job.

Oct 11, 2009 | 1999 Oldsmobile Bravada

1 Answer

98 Olds LLC - AC works but fan air does not blow


If you have a late model GM car and the system is controlled electronically the blend door actuator becomes weak. When this situation occurs it will not move the air direction door inside of the heater/air conditioner plenum. in your case not to the vents Replace the actuator with new and recheck the system. i hope this helps

Jul 24, 2009 | 1995 Oldsmobile Cutlass Ciera

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...