Question about Toyota Cars & Trucks

Open Question

How is car fixed to solved Camry 1997 P007 check code

Check light on--shop saw code P0007--rare they said. How to fix it? they didn't know shop didn't know how to fix. what now? 1997 Camry check code P0007. Shop didn't know solution. What now?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76649 Answers

SOURCE: check engine light on,2 days

This is a trans range switch code, try this: on top of the transmission, by the selector lever, there is the range switch, remove the electrical connector to the switch and clean the terminals inside the connector, add some dielectric gears to the terminals (avail at any parts store), and reconnect. Disconnect negative battery terminal for 60 sec., reconnect switch, drive the car a few d ays and see if MIL light come on again.

Posted on Aug 28, 2008

Ad
lebones337
  • 152 Answers

SOURCE: sensor 1 bank has an open circuit

it is the O2 sensor in the manifold that went bad. it is an easy fix but i wouid recommend taking in to somwere other than the dealer to save you money. this is small problem that will only effect your gas milage a little

Posted on Jan 02, 2009

  • 97 Answers

SOURCE: 2004 chrysler pacifica check engine light code

The codes are both evap system codes. The only good way to find the leaks is to take it to a shop that has a smoke machine. They will pump smoke into the evap system to find the leak.

Posted on Jan 27, 2010

Mackmech11
  • 122 Answers

SOURCE: check engine lights on 99 ford ranger ODB codes

DTC P1506 is set when the PCM detects the engine idle speed is greater than the desired rpm. This is most commonly caused by a dirty or bad IAC valve. Cleaning the throttle body will, most likely, cure this problem.

p1131 means that the bank #1 O2 sensor, the bank closest to the firewall, cylinders 1-3 is showing a lean mixture. Could be a vacuum leak, a misfire on that bank, an exaust leak upstream of the O2 sensor, fuel control or injector problem on that bank, a faulty O2 sensor, faulty PCM, faulty wiring in the engine control wiring harness.

P0171
In the vast majority of cases, simply cleaning the MAF sensor does the trick. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling also Inspect all vacuum and PCV hoses, replace if necessaryCheck for a dirty fuel filter and proper fuel pressure

Posted on May 19, 2010

duane_wong
  • 6826 Answers

SOURCE: Toyota Corolla 1997 P1300 diagnostic

p1300 is random misfire. It can be caused by a bad O2 sensor, in some cases.

Good luck on this repair.

Posted on Jan 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Error code p0007 on my 2005 dodge durango. Won't start just cranks over and over never fires up


The "Fuel Shutoff Valve "A" Control Circuit High" indicates the problem may lie in the electrical circuit in the fuel shutoff valve control.

Jun 23, 2016 | Dodge Cars & Trucks

2 Answers

What does fault code P0007 mean for Dodge Nitro


That code thrown up on generic DTC definitions is "Fuel Shutoff Valve. A Control Circuit Open."
The fix???

Jul 23, 2015 | Dodge Cars & Trucks

1 Answer

My 1997 Toyota Camry Check engine light just came on and i put it on the code reader an code P1133 came up can you tell me what thid mean thanks .


P1133 refers to the air/fuel ratio sensor bank 1 sensor1 (This is the first O2 sensor in the exhaust). the code indicates that the circuit is either open, shorted, or has a poor connection. Most of the time this can be fixed simply by removing, cleaning, and reinstalling the sensor (checking the connections in the process). if after reinstalling (and having the code cleared from memory) the light comes back on you should replace the sensor.

Feb 07, 2014 | 1997 Toyota Camry

1 Answer

1997 toyota camry how do you fix a p0340 camshaft sensor A_ bank 1 circuit malfunction


Well, a lot depends on what is causing the P0340 Diagnostic Test Code (DTC) to set.

The Camshaft Position Sensor (CMP) is a pick-up coil mounted in the outer corner of the left cylinder head just below the valve cover (assuming your Camry is equipped with a V-6...you didn't say)
a one tooth signal plate is mounted to the outer camshaft. DTC P0340 sets when there is no signal recieved from the sensor by the Engine Control Module (ECM) either during engine cranking or engine running.
Possible causes are:
> Open or short circuit in CMP sensor circuit
> Faulty CMP sensor
> Defective starter
> Damaged cam signal plate
> Broken timing belt
> Internal ECM problem
Proper diagnosis required.

Jun 09, 2012 | 1997 Toyota Camry

1 Answer

Check engine light is on


The check engine light can come on for many differant reasons.The light is triggerd by sensores that monitor the performance of your engine.This could be somthing minor from a faulty gas cap to a major emmissions problem.Unless you have or someone you know has a code reader you will have to take car to shop and have code read to see what problem might be.Shop around because its around 50 to 100 dollars just to read code without fixing the problem.

Feb 09, 2011 | 1998 Toyota Camry

1 Answer

1997 camry toyota rear running lights dont work. bulbs are fine and all other electronics work, why is this and how can i fix it?


look for a tail light relay and fuse--probably in the engine compartment relay box. Try swapping the tail light relay with the horn relay and see if the lights work. If yes, replace the relay. Please let me know if you have more questions.
jturcotte_26.gif

Nov 03, 2010 | 1997 Toyota Camry

1 Answer

Obd code 401 and 402 for 1999 toyota camry


There are 3 types of mechanics...one who is willing to help and solved the problem right away...very rare, second is fixed the problem, but will loosen other connections so the car will be returned for repairs again. Based on experienced, the mechanic who last worked at my sisters car loosen the connection of his 1999 Toyota Camry EGR port to the engine and she is getting DTC 401, and the last is... guessing games for non-experienced mechanics. My sister is a victim being an unsuspecting customer who doesn't know anything about cars. The world needs money...Suggest don't dress as if you are an executive who earns lots of money and their impression to you is that money is not an object, get referral to friends who had car problems and was fixed without going around the bush. Nowadays, you don't know who are good and bad mechanics.

Aug 01, 2009 | Toyota Camry Cars & Trucks

2 Answers

Check engine lite comes back on


I had the same problem on a 03 Avalon. It is the connector that comes with the "generic" sensor you bought. It tests fine, but the computer somehow sees the resistance in the connector. I even cut it out and soldered the connections, still no luck. Took car to a local shop and they said they had the same issue with generic sensors and quit using them. Bought the Bosch sensor with the factory plug (best price is on amazon.com) and problem solved.

Jul 06, 2009 | 1997 Toyota Camry

1 Answer

Brake light is show up most of the time


Brake lite on? Check master cylinder. Low on fluid. Your front brake pads are probably low also.
Cig lighter/clock/mirror and probably the dome light out too? Check fuses under dash.
Took in for check engine light? What was the code and what did they do?

Apr 10, 2009 | 1998 Toyota Camry

2 Answers

1997 toyota camry check engine light on codes are po441,po446


p0446 is an evap code for incorrect purge flow, check the rear vacume switching valve. its above the rear sub frame

Apr 05, 2009 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...