Question about 2001 Ford Windstar

Open Question

Where my 2002 ford windstar map sensor - 2001 Ford Windstar

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 22326 Answers

SOURCE: change oxygen sensor 2001 ford windstar

fist unclip wire,then unscrew it with a 28mm spanner ,fitting procedure is the reverse .It turns anticlockwise to unscrew and clockwise to screw up ,torque setting is a grunt and two scuffed knuckles and max of 3 swear words

Posted on Jan 01, 2009

  • 5 Answers

SOURCE: location intake air sensor 1999 ford windstar 3.8

follow your airbox usually front right side of engine and there should be a grommet or a similar attachment holding the sensor into the hose.

Posted on Mar 30, 2009

  • 34 Answers

SOURCE: 2002 Ford Escort ZX2 where is the map sensor

the map sensor is located on the intake manifold usually on the back of it to the right

Posted on Nov 20, 2009

  • 1068 Answers

SOURCE: 2002 Ford Windstar Error Code P1131 And P1151

those two codes are for the o2 sensors. both are the upstream sensors on the front and rear banks. so they are desinagted bank 1 sensor 1 and bank 2 sensor 1. them most common cause for this is faulty o2sensors , bad gas and of a poor running engine. so if your car runs good (no misfire) and gas is ok then replace the o2sensor witch is the very most common cause.

Posted on Jan 28, 2010

Testimonial: " Help With Problem But Where Are These O2 Sensor"

  • 8841 Answers

SOURCE: Where is the coolant sensor

Do you mean 3.8 litre? My manual does not show a 2.8 L engine. Here is location for a 3.8 L engine:


Posted on Oct 18, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 ford windstar lx error code 0171 & 0174

System too lean...possibly a bad maf/map sensor.

Jul 23, 2016 | Ford Cars & Trucks

1 Answer

Multiple missfires and lean mixture; where is the dptf the thing that replaces the map sensor

Find your egr valve than follow the hose from the egr to the sensor your looking for.

Aug 01, 2013 | 2002 Ford Windstar Cargo

1 Answer

P0171 what could be problem

p0107 refers to manifold absolute pressure(MAP) sensor barometric pressure (BARO) sensor--low input.--- causes-- wiring short to ground---map sensor baro sensor ECM. use only genuine units in replacement

May 18, 2013 | 1998 Ford Windstar

1 Answer

I have a 1998 Ford Windstar that sometimes stalls when coming to a stop and sometimes will kind of **** while driving it. I was told that it could be the MAP sensor. I was wondering where this was...

The MAP sensor is under the hood on the firewall , it has a single vacuum hose going to it , and a two wire plug.
simply unplug the wires to test it (if the van runs better w/o it pluged in , replace the sensor).

Mar 31, 2011 | 1998 Ford Windstar

1 Answer

I have a 2002 for windstar and its blowing out black smoke i bought it advance auto and the machine said the manufacturer control fuel air metering and the1st sensor 1 circuit dish input might be going out

Black smoke, running rich, two thing will cause that, CTS ( coolant temp. sensor) and MAP sensor, both work like a choke, check MAP senor first, make sure it has vacuum.

Aug 16, 2010 | Ford Windstar Cars & Trucks

1 Answer

Need location of map sensor 3.8 engine 95 windstar

this engine dos not use a MAP sensor it uses a MAF sensor, the MAF is located in the fexiable rubber air intake hose from the air cleaner to the engine. see photo.


Feb 03, 2010 | 1995 Ford Windstar

1 Answer

Oxygen sensors

you have 3, 2 upstream and one downstream. They have wire harnesses attached to them and they screw into the exhaust system. Ususally two in the exgaust crossover pipe, the other just behind the catalytic converter.

Oct 03, 2008 | 2002 Ford Windstar Cargo

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides