Question about 2007 Volkswagen Passat 3.6

Open Question

Fuel pressure sensor

How to installed a fuel rail pressure sensor on a 2007 vw Passat 3.6

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 71 Answers

SOURCE: front speaker installation for VW Passat

If you've not taken speakers out before they are easy to do, you have to pull the door trim off, first look if there are any screws and take them out then carefully pull the trim away from the door and using a torch you will see plastic holding clips you have to pull the trim off at that point, some will break but they are a few cent only and can be got from the VW dealer readily, take your time and you "might" not break any of them, I find a plastic 12" ruler to be handy along with a flat bladed screwdriver, first cover all the blade of the screwdriver with masking tape to stop any damage if you slip.
very simple job to do just take your time and dont rush the clips have a tough hold on the doors also.

Posted on Nov 28, 2008

  • 1 Answer

SOURCE: 1995 VW Passat Oil Pressure Sensor/Leak

ya honestly just fixed that on my 1993! its not a big deal but u got to break it lose with a 24mm deep socket and it works!

Posted on Jan 08, 2009

  • 345 Answers

SOURCE: Handbrake in VW Passat 2007 got Stuck

a very common fault is the switch,the calipers are not much better,they will be able to sort it for you but they are bad news for a modern car !!

Posted on Jan 19, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

  • 1 Answer

SOURCE: 99 vw passat sw 1.8t #3 cyl not firing.

ihad the same problem.. its not the coils or anything like that.. and any reg mechanic wont know the prob unless they under vw.. u need to replace ur power output stage.. thats what cylinder 3 misfire is.. after i fixed it my car is good as new. i

Posted on Oct 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 VW Passat cranks won't start. fuel pump works,fuel up to fuel rail, spark plugs do fire


Improper fuel/air mixture, possibly plugged up air filter?
You have 2 out of 3 of the needed components for that motor to run, and assuming your timing is correct and you have compression, it could be an air intake issue.

Feb 24, 2017 | 1998 Volkswagen Passat

1 Answer

My 2007 Toyota isis iaz.read code P0191


Anon, Trouble code P0191, You may need a good tech. with scan tool to read and test system.
  • Fuel Rail Pressure Sensor Circuit Range/Performance,computer see's signal from the Fuel Rail Pressure Sensor and/or its circuit is sending erratic readings, indicating a fuel pressure condition that is abnormal. Problems could be out of gas, leaking fuel, faulty fuel pressure sensor, bad wire or plug in circuit,fuel pressure regulator, the fuel pump could be faulty also. Check the attached links,instruction and guides, Good luck
    "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
P0191 OBD II Trouble Code

P0191 Fuel Rail Pressure Sensor Circuit Range Performance

RAV4 2001 Trouble Code p0191 probable solution Toyota Nation Forum Toyota...

code P0191 2007 Toyota Google Search

May 03, 2016 | Toyota Cars & Trucks

1 Answer

What does the p0190 code on my 2008 VW tiguan mean. It does have a rev problem


code p 0190 refers to fuel rail pressure (FRP) sensor---circuit malfunction===causes --wiring--fuel rail pressure sensor ---ECM
replace the sensor

Mar 03, 2016 | Cars & Trucks

1 Answer

Where is fuel pressure regulator located 2007 VW 2.0T (Passat)?


It is on the end of the fuel rail, and easy to replace just by removing the clips. There is also a vacuum hose. But test rail fuel pressure first.

Oct 10, 2015 | 2007 Volkswagen Passat 2.0T

1 Answer

Where are the pressure control solenoids located on 2002 vw Passat 2.8 l 2 wheel drive


Right at the far end of the main fuel rail on top of the engine.
It also have a vacuum line to it.

Apr 24, 2015 | 2002 Volkswagen Passat

1 Answer

My VW Passat wont start it cranks over has fuel at the fuel rail but no spark I removed a spark plug lead and placed a plug on it shorting the plug to earth cranked the engine over and not spark for a


check that the cam shaft is turning ( broken timing belt/chain will not allow position sensors to give spark). Check that the immobiliser is operational. have the fault codes read

Oct 05, 2014 | 2001 Volkswagen Passat

1 Answer

What would cause a combination of P0304 and P2293 OBD codes on a 2007 Passat 2.0T?


P0204 is miss fire detected on #4 cylinder.

Below is TSB from VW on your problem...a common one.


Technical Product Literature Transaction No.: 2015153/1
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory Release date: Jun 29, 2007
Condition
15 07 04 June 29, 2007 2015153
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory
MIL ON with the following DTCs may be stored in ECM fault memory:
DTC Description
P0087 Fuel Rail / System Pressure - Too Low
P1093 Fuel Trim 2, Bank 1 Malfunction
P2293 Fuel Pressure Regulator 2 Performance

Technical Background
Excessive wear of intake camshaft lobe that drives the high pressure fuel pump. The wear limits maximum pump piston lift, causing fuel rail pressure fluctuations.
The wear on the camshaft lobe can also lead to wear on the base of the high pressure fuel pump cam follower.
Production Solution
Increase surface hardening of camshaft lobe for the high pressure fuel pump
Improved intake camshafts have Part No. 06F109101B.
Service

• Remove the high pressure fuel pump and visually inspect:
1. Base surface of the cam follower -6- in contact with the camshaft lobe.
2. Tip of the high pressure fuel pump plunger.
3. High pressure fuel pump camshaft lobe.

If the base of the cam shaft follower looks like -C- or -D-, no excessive wear is present.
Cam follower and camshaft should not be replaced.
If the cam follower base surface is excessively worn so that its surface is concave -B- or missing -A-, inspect the intake cam shaft lobe for wear.

cam.jpg

If the high pressure fuel pump camshaft lobe shows excessive wear, replace the intake camshaft with Part No. 06F109101B and the cam follower with Part No. 06D109309C, see Group 15 Engine - Cylinder head, Valvetrain in ElsaWeb.

Inspect the tip of the high pressure fuel pump plunger for excessive wear.
If excessive wear is found the high pressure pump must also be replaced, see Group 20 Fuel supply in ElsaWeb.
Tip:
High pressure fuel pump plunger damage is only possible if the cam follower base has a hole in it and the plunger tip has come in direct contact with the camshaft lobe.
If no excessive wear can be found in the high pressure fuel pump cam follower or intake camshaft lobe, or if the damage is found in camshafts with part number 06F 109 101 B, create a Technical Assistance Contact Ticket under the Concern Type Engine and Engine Electronics in ElsaWeb.
Attach the complete diagnostic log to the contact, and call the VW Technical Assistance Center for further assistance.

Warranty
When procedure applies to vehicles within the New Vehicle Limited Warranty, use the following:
Claim Type: W2
Part Identifier: 1505
Damage Code: 1505 18 _ _ _* 2
Labor Operation:
2.0T FSI engine Use applicable SRT time in ElsaWeb
Diagnostic Time: Actual GFF time expenditure
Claim Comment: Input "As per Technical Bulletin 2015153" in comment section of Warranty Claim.

* Code per warranty vendor code policy.
Required Parts and Tools
Description Part No: Quantity
Intake Cam Shaft 06F109101B 1
Cam Follower 06D109309C 1

No Special Tools required.

Aug 19, 2011 | 2007 Volkswagen Passat Sedan

1 Answer

I need to replace de fuel presurre sensor in a pontiac montana ,do i have to just replace the sensor ,o the sensor came with the fuel pump?thank you


Replacing the fuel pressure regulator, involves just replacing the regulator at the end of the fuel rail in the engine compartment, but fuel pressure sensor - does this mini-van have a fuel pressure sensor?
replacing the fuel pressure regulator: (1) locate it at the end of the fuel rail in the engine compartment,
(2) relieve fuel system pressure (3) disconnect fuel pressure regulator vacuum line. (4) remove fuel pressure regulator retaining screw (retain for re-use (5) using a shop towel to catch spilled fuel, lift & twist Fuel pressure regulator to remove it from the fuel rail. (6) remove/discard retainer and spacer bracket from the fuel rail. (7) remove fuel pressure regulator from the engine fuel return pipe. (8) remove/discard Fuel Pressure Regulator inlet O-ring (9) Check Fuel Pressure Regulator filter screen for contamination - if contaminated, replace Fuel Pressure Regulator. (10) Lubricate new Fuel Pressure Regulator inlet O-ring with clean engine oil & install onto the Fuel Pressure Regulator inlet. (11) Install the fuel return pipe onto the Fuel Pressure regulator (12) Install new retainer & spacer bracket into the slot on the fuel rail.
(13) Install Fuel Pressure Regulator onto Fuel Rail & tighten Engine Fuel Return Pipe nut to 13 ft-lbs (17 Nm). (14) connect Fuel Pressure Regulator vacuum line, (15) Install Fuel Pressure Regulator attachng screw & tighten to 76 in-lbs (8.5 Nm). (16) Inspect & verify that retainer & spacer bracket is engaged in the slots on the fuel rail. Grasp & pull on the Fuel Pressure Regulator.
to ensure that the Fuel Pressure Regulator is properly seated. (17) inspect for fuel leaks with this
procedure: On 2sec,(holy rollers), off 10sec will be left on, inspect for leaks while running.

Dec 11, 2010 | 2000 Pontiac Montana

Not finding what you are looking for?
2007 Volkswagen Passat 3.6 Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...