Question about Cars & Trucks

1 Answer

96 grand cherokee 4litr stalls out was throwing codes 351 420 fixed them new parts stopped for a couple weeks just started again

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 88 Answers

Get rid of this car if U can - they r plauged with electrical problems - too many vibrations. Sorry 2 tell U the bad news......Good luck!!!

Posted on Nov 23, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: 96 grand cherokee crank no start, no spark from

have the crank sensor replaced this controls the spark and injector pulse it is located on the drivers back side of the engine above the transmission housing!

Posted on Jun 11, 2009

Mikey108
  • 475 Answers

SOURCE: 96 jeep Grand Cherokee tailgate will not open

This is kind of tricky. OK let's start, you have to crawl into the rear hatch area from the inside of the car. You'll have to pull the rear panel off the hatch, a screwdriver between the panel and hatch near the window will work. There might be 2 screws on the panel you could take out. The trick is to pull the panel far away enough to stick your arm down towards the latch and release it by hand. We did this at the dealer all the time.

Posted on Nov 19, 2008

  • 94 Answers

SOURCE: 2004 Jeep Grand Cherokee. Keeps stalling, engine

P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Posted on Oct 27, 2009

  • 52 Answers

SOURCE: 96 Jeep Grand Cherokee diagnostic codes P1762 and

governor pressure sensor in transmission is the likely problem

Posted on Nov 22, 2009

  • 54 Answers

SOURCE: my grand cherokee stalls at

TRD Communication error:

http://www.readmanual.com/profile/v.cgi?2632.cars/jeep/cherokee/2002
http://www.readmanual.com/profile/v.cgi?2633.cars/jeep/cherokee/2002

Posted on Dec 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep grand cherokee zj 96. Run good while not moving, then for a few minutes will drive great before spitting and spluttering and losing all power and now will stall. Then if I turn off and restart it...


The first thing to do to save money when the engine stops performing is to run the fault codes. I suggesting that if you do you will find a fault with the canister purge valve /solenoid that is preventing the fuel getting to the injectors.

Sep 28, 2013 | 1997 Jeep Grand Cherokee

1 Answer

Hello my 2004 Jeep Grand Cherokee keeps stalling


new guest: Have the same problem with 2004 Grand Cherokee Limited. No one can seem to find the problem.
Answer is never buy a jeep again.

Jun 28, 2010 | 2004 Jeep Grand Cherokee

2 Answers

2001 Jeep grand cherokee limited v8 engine, did diagnostic test and code P0320 came up. Wondering what needs to be done, and if possible, if diagram


Hello...

P0320 means "No Crank Reference Signal To PCM"

The Crank Position Sensor needs to be checked.

Good Luck

Dec 12, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Crankshaft position sensor issues


Likely the sensor is too close to the flywheel. Most sensors will work with a clearance up to 1/4". It can easily be shimmed back a bit by using a few spacers made from an aluminum can etc. Hope the converter is installed correctly and that the flywheel isn't damaged!
Good Luck!

Nov 26, 2009 | 1996 Jeep Grand Cherokee

1 Answer

I HAVE 95 JEEP GRAND CHEROKEE. AFTER DRIVING CAR FOR SHORT DISTANCE WILL NOT START. LET SET COUPLE HOURS IT WILL START. MAY GO 5OR 6 DAYS NO PROBLEM THEN AGAIN WILL NOT START. HAD TWO GUY CHECK IT wE...


Had similar problem with 96 Jeep 4.0L engine. Tracked it down to the connector for the distributor pickup. Spliced in another connector and hasn't stalled since. Also, have you had any codes? Easy way to check on Chrysler products: turn key on, off, on, off, on (not starting) and watch the 'engine light' on the dash. It will flash off/on. Count the flashes with short pauses between and longer pauses between code. When you get a 5 count and 5 count, that is the end. This may also help

Aug 10, 2009 | 1995 Jeep Grand Cherokee

1 Answer

1996 Jeep Grand Cherokee stalls when brakes are applied


My 2000 Grand Cherokee had the same problem, without all the sputtering, it would just die approaching a stop. We could only keep it running by slightly pushing down on the gas petal when coming to a stop. I replaced the Throttle Position Sensor, but that didn't change anything. A new mechanic I found replaced the Idle Air Control Valve, and we've had no problems in a week.

Jan 02, 2009 | 1986 Jeep Cherokee

3 Answers

Rough idle stalls at low rpm's


check your transmission fluid,the motor will stall when fluid is low

Dec 06, 2008 | 1996 Jeep Grand Cherokee

3 Answers

96 JEEP Gr Cherokee hesitates, surges, later stalls


You might want to start by replacing the crank sensor first.

Nov 24, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...