Question about 1998 Mercury Mystique

Open Question

Trying to get to the transmission filter.took pan off still dont see the filter

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change the filter on the automatic transmission on Honda civic 89?


In the Civic the Transmission Filter is located inside the transmission, you must remove the bottom pan of the transmission, the filter is just below the Valve body, remove all the bolts from the pan and with a large catch pan under the pan gently pry the pan down, it is very messy as there is no drain plug, install the new filter element and then clean off all the old gasket on the transmission pan and the transmission, reinstall the pan with the bolts just finger tight, then evenly tighten the pan bolts down to about 12 foot pounds, add about 1.5 quarts of the correct ATF type fluid and run the car at idle until the transmission is hot, then top off the transmission fluid level, DO NOT OVERFILL.

Nov 22, 2010 | 1989 Honda Civic

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Where is the tranny filter?


the transmission filter is located inside the transmission. Oil must be drained and Transmission oil pan must be removed to access the filter. Hopefully this helps

Aug 16, 2009 | 2004 Mitsubishi Endeavor

3 Answers

How to change trans. fluid and filter in a 2000 mitsu. mirage 1.8?


first you need to get a pair of safety glasses to protect eyes from cleaner. then you need 12.6 pts or 6.5 to 7 quarts of transmission fluid+ filter.you also need a drain pan to catch transmission fluid.you need a 3/8 ratchette and socket set.you need some paper towel and maybe1 or 2 cans of brake cleaner.now you want to safely raise and support car on jack stands.make sure you are on solid level ground.put drain pan under transmission to catch fluid.take ratchette wrench start removing tranny pan front and side bolts.loosen rear bolts one turn let the pan drain.when all tranny fluid drain out of pan. then remove pan clean it good with brake cleaner.remove all traces of old gasket. from pan then dry with paper towel..then you remove tranny filter.becareful not to damage anythingthen put in your new tranny filter then.wipe and carefully clean around gasket area on transmission with paper towel.make sure there is no traces of olds gasket material on tranny area where tranny pan gasket seals.now get new gasket align its with tranny pan holes.you might want to buy a gasket adhesive.just put on some to hold gasket in place when you install it to transmission.besure to clean all tranny pan bolts real good with brake cleaner. then dry them off real good.because some transmission you have to put a little rtv sealant on bolts.to keep them from leaking.now once you get bolt holesand gasket on transmission pan line up.all tranny pans bolts with a little rtv silicone on threads and on bolts head where they meet the pan.then you transmission pan in place.make sure gasket and bolt holes line up.when putting bolts in dont tighten them until you get them all in first.when all bolts are in.then you tighten criss cross dont over tighten them. torque them to 90 inch pounds .when all is done .starting putting tranny fluid in.and check for leaks.start the engine up let it idle for few minutes if you see no leaks lower car down to ground.then move transmission gear selector through each range and back to park.make sure tranny fluid level correct before driving car. WARNING IF YOUR CAR DONT HAVE THE TRANSMISSION DIP STICK.AND HAVE A FILL CAP INSTEAD THE DEALERSHIP HAS TO CHANGE FLUID.BECAUSE THEY HAVE TO RAISE CAR ON LIFT TO CHECK FLUID LEVEL.BECAUSE CAR HAS TO BE RAISE UP LEVEL THEN A DRIP PLUG IS MOVED TO CHECK TRANNY FLUID LEVEL.

Jul 19, 2009 | 2000 Mitsubishi Mirage

1 Answer

00' Kia Sephia LS not shifting past 1st gear


first you need to buy transmission fluid new filter and new gasket.you need 11.4 pints of transmision fluid.raise front of vechicle.set parking brake.block both back wheels.besure support vechicle weight with jack stands. get a drain pan.if your transmission pan dont have a drain plug.loosen rear pan bolts a few turns.remove the front and side transmission pan bolts. let fluid drain.remove tranny pan. then clean old gasket material from transmission and pan carefully.dont scratch or damage surface.clean old tranny bolts using brake cleaner or buy new tranny bolts.you have to put a tiny film of rtv silicone on tranny bolts so they wont leak.carefully remove old tranny filter and put on new filter.clean all grease grim away from tranny pan it should be **** and span because.you might need a little gasket adhesive to hold gasket in place while putting pan back on transmission.to line up bolt holes.loosely put all bolts in you have to move pan a little to get holes line up.when all is finish put tranny fluid back in.besure you put 11.4 pints back in that about 6.5 quarts. make sure tranny fluid level is right before driving vechicle.l

Jun 19, 2009 | 2000 Kia Sephia

1 Answer

Took transmission pan off and can't find filter


2002 Hyundai Elantra has 2 trans filters. One is inside the pan which is mounted vertically. The other is located on top of the transmission case.

Apr 22, 2009 | Hyundai Motor 2002 Elantra

1 Answer

Where is trans filter?


The transmission filter in your vehicle is inside the transmission. It requires transmission removal and overhaul to be replaced.

The transmission filter in your vehicle does not need to be replaced unless the transmission is being rebuilt.

Oct 03, 2008 | 2001 Hyundai Elantra

8 Answers

Where's transmission filter located?


Filter is not in the pan- my wife has an '03 Tribute with the 3.0, and trust me, it's not under the pan. From everything I have read, it's inside the tranny someplace and not accessible without tearing the thing out and down.

And, yes there is a drain plug on the side/bottom of the tranny case- you can use a 3/8" ratchet w/o a socket on it to loosen/tighten.

Aug 02, 2008 | 2003 Ford Escape

3 Answers

Where's transmission filter for 2002 ford escape


the transmission filter is located in the transmission pan.
remove the pan note: there is no drain plug. once you have removed the transmission pan the filter will be visible.
clean area and apply new gasket than reassmeble.

Aug 02, 2008 | 2004 Ford Escape

2 Answers

Flushing the transmission


To change the transmission fluid make sure you have purchased: 1. filter with the o-ring 2. MOPAR ATF + 3 Type 7176, p/n 05010124AA fluid (I believe it took 6 quarts?) You are not changing the torque converter fluid so there will not be 12 quarts needed.). 3. Pan gasket. You should receive the new neoprene reusable pan gasket. This is because the recommendation is to change the transmission fluid every 25,000 miles. 4. There is a fluid additive to prevent foaming? Use it.


Raise the vehicle on a hoist. Remove the pan bolts. Remove the old gasket material with a plastic scraper. There could be metal transfer if you use a metal scraper. Clean the pan carefully. Clean the magnet that sits in the pan as it collects the minute metal shavings. If you see an excess of larger particles, you really should have the transmission inspected at a shop. Replace the filter carefully looking at its arrangement before removing. It took a second look to install a new filter because I did not watch how it was situated before removing. Use a thin coat of transmission fluid on the new pan gasket. Orient reusable gasket properly with bolt holes and assemble oil pan and gasket to transmission case. Tighten oil pan bolts to 19 Nm (165 in lbs.). CAUTION: DO NOT OVERFILL TRANSAXLE. DO NOT ADD OIL IF LEVEL IS BETWEEN: LOWER HOLES FOR WARM OIL (100?F). UPPER HOLES FOR HOT OIL (180?F.).

Jun 12, 2008 | Chrysler Neon Cars & Trucks

Not finding what you are looking for?
1998 Mercury Mystique Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...