Question about Toyota Land Cruiser

1 Answer

Replace fan belts

What tools required

Posted by on

Ad

1 Answer

A few metric open end wrenches in most cases there is nothing bigger than a 21 mm so if you have 8 mm to 17 mm wrench set your set

Posted on Nov 23, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
sodeep
  • 3267 Answers

SOURCE: replacing fan belt?what tools are

Instructions

Things You'll Need
3/8-inch drive breaker bar
Metric sockets
Serpentine belt

1 Open the hood and inspect the flat surface on top of the plastic fan shroud for the belt routing diagram. Follow the diagram instructions to route the new belt.

2 Locate the serpentine belt self-adjusting tensioner on the front of the engine block. The tensioner has a pulley on the bottom of the tensioner arm, which the belt travels under. The tensioner can only be rotated from the bolt that secures the pulley to the tensioner arm.

3 Rotate the tensioner in a clockwise motion with a metric socket and the breaker bar to loosen the tension from the belt. Then, pull the belt off the top of the tensioner pulley. Release the tensioner pulley and pull the breaker bar off the pulley bolt.

4 Pull the belt out of the accessory pulleys. Then, slide the belt around each fan blade and out of the engine bay. Rotate each fan blade to the top side of the engine to get the belt around each fan blade.

5 Match both the new belt and the old belt together to make sure that the new belt is the correct size. Then, route the new belt around each fan blade and around the crankshaft pulley. The crankshaft pulley is the big pulley at the very bottom of the engine.

6 Follow the routing directions from the belt routing diagram to install the new belt around the other accessory pulleys. Once the belt has been routed around all of the pulleys, look over the belt and make sure that it is secure inside all of the pulleys.

7 Crank the 1998 Dodge Caravan and let the motor run for about 15 seconds. This will finish seating the ridges of the new belt into the grooves of each accessory pulley.

8 Shut the motor off and close the hood.

Posted on Jul 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992. How do I replace fan belt? fan belt


There is a spring loaded belt tensioner. Use the appropriate tool to release the tension on the belt Remove the belt , paying attention to the belt routing and replace the old belt with the new belt.

Oct 13, 2015 | Ford Explorer Cars & Trucks

1 Answer

How to remove 2006 chevy Malibu cooling fan assembly


I think this is a fan which has a large nut with left hand threads and requires a (you guessed it) special tool. Most auto parts stores have a "loan a tool" program and should have this tool and be able to explain how to use it. Once you break it loose, get the tool out of the way and spin it off by hand, being very careful to not let it fall into the radiator as it comes off. Replace all belts and tensioners while your at it.

Oct 18, 2014 | 2006 Chevrolet Malibu

1 Answer

How to replace fan belt on siroin


When replacing fan belts, route the new belt through the pulleys so that it uses the exact same path as the old belt. You may need to loosen the belt tensioner a little bit more in order to slip the new belt onto the final pulley.-------------------------------------------------------------------------------
ECU Chip Tuning Tool

Nov 29, 2012 | Cars & Trucks

1 Answer

Nissan primera p10 changeing fan belt


It depends on the vehicle. Most are not too difficult to change though. It requires loosening or moving a tensioner and then putting the new belt on. The hardest part is usually getting the belt going the right direction around the right pulleys. There is usually a diagram to help on the inside of the hood or near the belt.
----------------------------------------------------------------------------------------------
VAG diagnostic tools

Nov 16, 2012 | Cars & Trucks

1 Answer

Nissan p10 changing fan belt


It depends on the vehicle. Most are not too difficult to change though. It requires loosening or moving a tensioner and then putting the new belt on. The hardest part is usually getting the belt going the right direction around the right pulleys. There is usually a diagram to help on the inside of the hood or near the belt.
-----------------------------------------------------------------------------------------
VAG diagnostic tools

Nov 16, 2012 | Cars & Trucks

1 Answer

Replacing fan belt?what tools are required?


Instructions

Things You'll Need
3/8-inch drive breaker bar
Metric sockets
Serpentine belt

1 Open the hood and inspect the flat surface on top of the plastic fan shroud for the belt routing diagram. Follow the diagram instructions to route the new belt.

2 Locate the serpentine belt self-adjusting tensioner on the front of the engine block. The tensioner has a pulley on the bottom of the tensioner arm, which the belt travels under. The tensioner can only be rotated from the bolt that secures the pulley to the tensioner arm.

3 Rotate the tensioner in a clockwise motion with a metric socket and the breaker bar to loosen the tension from the belt. Then, pull the belt off the top of the tensioner pulley. Release the tensioner pulley and pull the breaker bar off the pulley bolt.

4 Pull the belt out of the accessory pulleys. Then, slide the belt around each fan blade and out of the engine bay. Rotate each fan blade to the top side of the engine to get the belt around each fan blade.

5 Match both the new belt and the old belt together to make sure that the new belt is the correct size. Then, route the new belt around each fan blade and around the crankshaft pulley. The crankshaft pulley is the big pulley at the very bottom of the engine.

6 Follow the routing directions from the belt routing diagram to install the new belt around the other accessory pulleys. Once the belt has been routed around all of the pulleys, look over the belt and make sure that it is secure inside all of the pulleys.

7 Crank the 1998 Dodge Caravan and let the motor run for about 15 seconds. This will finish seating the ridges of the new belt into the grooves of each accessory pulley.

8 Shut the motor off and close the hood.

Jul 07, 2011 | 1998 Dodge Caravan

2 Answers

Remove clutch fan dodge dakpta 4.7


This one does require a tool to loosen the fan clutch from the water pump shaft. Part of the tool holds the pulley and the other part is spanner wrench used to loosen the clutch. An important note on these fan clutches: Once you have the fan clutch off DO NOT let it lay with the rear side of the fan pointing downward as the silicone fluid that provides the "clutch" action can drain into the bearing and cause the clutch not to work. Once you have the clutch off just lean the fan and clutch against something so it is standing upright just as it is when it's bolted to the water pump until you are ready to put it back on. Hope this helps you out a bit!

Jul 11, 2010 | 2001 Dodge Dakota

1 Answer

How to change water pump (1997 sonoma)


The text below is from the GM Service manual 4.3L V6 Engine
Water Pump Replacement (4.3L)
Removal Procedure
Drain the cooling system. Refer to Draining and Filling Cooling System .
Loosen the water pump pulley bolts.
Remove the cooling fan and clutch assembly.

Tools Required
J 46406 Fan Clutch Wrench

Removal Procedure
Remove the upper fan shroud.
Remove the fan clutch from the water pump in a counterclockwise direction using the J 46406 .
Remove the fan clutch assembly.
Remove the drive belt. Refer to Drive Belt Replacement Remove the water pump pulley mounting bolts.
Remove the water pump pulley.
Remove the radiator outlet hose clamp from the water pump.
Remove radiator outlet hose from the water pump.
Remove the water pump mounting bolts.
Remove the water pump from the engine.
Remove the water pump gaskets.
Clean the water pump gasket mating surfaces.
Installation Procedure
Install the water pump gaskets.
Install the water pump to the engine.
Apply a sealer (GM P/N 12346004) to the bolt threads.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Install the water pump mounting bolts.
Tighten
Tighten the mounting bolts to 41 N·m (30 lb ft).
Install the radiator outlet hose to the water pump.
Install the water pump pulley.
Install the water pump pulley bolts.
Tighten
Tighten the water pump pulley bolts to 25 N·m (18 lb ft).
Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.
Install the fan clutch assembly.
Fill the radiator cooling system. Refer to Draining and Filling Cooling System .
Inspect the cooling system for leaks.

Oct 01, 2009 | 1997 GMC Sonoma

1 Answer

Replacing water pump on 89 s15 jimmy (4.3)


if you need that tool... stop in at autozone and borrow it... i suspect you would have to leave a deposit. but you get that back when you return the tool (if it's required). i think you only need that tool if the fan is one of those centrifucal type that stops spinning when you are are highways speeds.

robert

please take a moment to rate this solution.

p.s. if the pulley keeps turning when you try to take off the bolts...have someone push there thumb on the fan belt... that will provide tension and stop the pulley from turning.

Apr 17, 2009 | 2003 GMC Sierra 2500HD

1 Answer

Changing the water pump on 2000 Jeep Grand Cherokee V6


WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Jan 10, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...