Question about 2003 BMW 745 Li

Open Question

Warning light says Vechical detects increased body roll in curves. Avoid high cornering speeds

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My toyota voxy 2002 model was put on diagnostic machine and gave us fault code p1215 what do i check


- Faulty EDU - EDU harness is open or shorted - EDU circuit poor electrical connection - Faulty Spill control valve What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P1215 Description The EDU drives the spill control valve at high speeds. The EDUs high speed driving under high fuel pressure conditions is achieved through the use of a DC/DC converter that provides a high voltage, quick charging system. The engine ECU constantly monitors the EDU and stops the engine in case an abnormal condition is detected. The battery voltage is increased by the DC/DC converter. A voltage of approximately 50 V is applied to the spill control valve in accordance with the IJ+ signal received from the engine ECU. At this time, the injection verification signal (IJF) is sent to the

Read more: http://www.autocodes.com/p1215.html

Nov 05, 2016 | Toyota Cars & Trucks

Tip

Save Money on Gas/Petrol


  1. Avoid idling. While idling, your car gets exactly 0 miles per gallon while starting the car uses the same amount as idling for 6 seconds. Park your car and go into the restaurant rather than idling in the drive-through. Idling with the air conditioning on also uses extra fuel. Also, avoid going so fast that you have to brake for someone. Whenever you brake, you waste the gas it took to get going that fast.
  2. Drive at a consistent speed. Avoid quick acceleration and hard braking. Cruise control will keep you at a constant speed, even when going up and down hills.
  3. Avoid stops. If approaching a red light, see if you can slow down enough to avoid having to actually stop (because you reach the light after it is green). Speeding up from 5 or 10 miles per hour will be easier on the gas than starting from full stop.
  4. Anticipate the stop signs and lights. Look far ahead; get to know your usual routes. You can let up on the gas earlier. Coasting to a stop will save the gasoline you would otherwise use maintaining your speed longer. If it just gets you to the end of a line of cars at a red light or a stop sign a few seconds later, it won't add any time to your trip. Ditto for coasting to lose speed before a highway off-ramp: if it means you catch up with that truck halfway around the curve instead of at the beginning, you haven't lost any time. In many cities, if you know the streets well, you can time the lights and maintain the appropriate speed to hit all green lights. Usually this is about 35 to 40 MPH.
  5. Slow down. Air resistance goes up as the square of velocity. The power consumed to overcome that air resistance goes up as the cube of the velocity. Rolling resistance is the dominant force below about 40 mph. Above that, every mph costs you mileage. Go as slow as traffic and your schedule will allow. Drive under 60-65 since air grows exponentially denser, in the aerodynamic sense, the faster we drive. To be precise, the most efficient speed is your car's minimum speed in it's highest gear, since this provides the best "speed per RPM" ratio. This is usually about 45 to 55 miles per hour.
  6. Use A/C only on the highway. At lower speeds, open the windows. This increased the drag and reduces fuel efficiency, but not as much as the AC at low speeds (35-40 mph). The air con - when used a lot - is known to use up about 8% of the fuel you put into your car.

on Jul 31, 2010 | Acura Integra Cars & Trucks

1 Answer

2006 wrench light is on


Powertrain Malfunction (Wrench) Warning Indicator (base instrument cluster)
The instrument cluster receives the powertrain status from the PCM over the high speed CAN. When a powertrain system concern is detected, the PCM sends the instrument cluster a command signal to illuminate the powertrain malfunction (wrench) warning indicator. If the 4WD control module detects a failure with the 4WD drive system, the 4WD control module sends a message to the instrument cluster over the CAN to illuminate the powertrain malfunction (wrench) warning indicator. On 4.6L engines, if the transmission control module (TCM) detects a failure with the transmission, the TCM sends a message to the instrument cluster over the CAN to illuminate the powertrain malfunction (wrench) warning indicator.
better have it checked !
Bett

Sep 10, 2016 | 2006 Mercury Mountaineer AWD

3 Answers

COULD THE GAS PEDAL CABLE CAUSE THIS CODED PO507 to be high


Extracted from Engine-Codes.com

Code P0507

Possible causes

- Dirty throttle body

- Electric throttle control actuator misadjusted or damaged

- Faulty Electric throttle control actuator

- Intake air leak

- Poor electrical connection to the Intake Air Control (IAC) valve


help.jpg What does this mean?

Tech notes

If there are no intake leaks, clean throttle body, adjust engine idle and erase engine code. If the code comes back you may have to replaced the Electric Throttle Control Actuator (Motor) to repair the problem.



There is a factory service bulletin for the following Chevrolet models:



2006-2008 Chevrolet Trail Blazer

2007-2008 Chevrolet Avalanche

2007-2008 Chevrolet Express

2007-2008 Chevrolet Silverado

2007-2008 Chevrolet Suburban

2007-2008 Chevrolet Tahoe

Chevrolet Factory Service Bulletin OBDII Code P0507


What does this mean?

When is the code detected?

Thi P0507 code sets when the Powertrain Control Module (PCM) detects an engine speed outside of the Idle Air Control (IAC) valve range of control.

Possible symptoms

- Engine Light ON (or Service Engine Soon Warning Light)

- Engine hard to start

- Rough or erratic idle speed

P0507 Chevrolet Description

The Idle Air Control (IAC) valve is a Powertrain Control Module (PCM) controlled stepper motor located on the throttle body. The stepper motor drives a valve pintle which protrudes into a passage that bypasses the throttle plates. The PCM commands the IAC valve pintle to extend to decrease the idle speed. The bypass air flow is reduced and the idle speed decreases as the pintle approaches its seat. The PCM retracts the IAC valve pintle away from its seat to increase the idle speed. The retracting of the IAC valve pintle allows more air to bypass the throttle plates. One of the PCMs uses for the IAC system is to maintain a desired idle speed. This DTC sets when the PCM detects an engine speed outside of the IAC\'s range of control.





Read more: http://engine-codes.com/p0507_chevrolet.html#ixzz3ObdI2chF

Jan 11, 2015 | 2001 Chevrolet Blazer

2 Answers

While starting vehicle ETC warning display vehicle not throttle


This is a warning that something needs to be checked. This happens a lot when a vehicle is jumped with a dead battery. You may have to take to dealer and have ETC reprogramed.
Throttle Control Warning Light More and more vehicles are doing away with the mechanical throttle cable between the driver's foot and the engine throttle body, replacing it with a "drive-by-wire" system. In this system, a throttle pedal sensor sends data to an electronic throttle control computer, which evaluates and relays the throttle request to a specialized electronic throttle motor on the engine throttle body.
The throttle motor opens or closes the actual throttle blade, which increases or decreases the power output of the engine. The throttle control warning light illuminates when a problem is detected in the electronic throttle system.

Jan 04, 2015 | Cars & Trucks

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

Air ride is there a control in the car for this??? Mine went down in the rear and than came back by itself???


some of the 4 by 4s are speed sensitive
when on rough ground suspension hgher but level ground increased speed lowers automaticall to avoid roll over maybe your system is the same

Feb 08, 2011 | 1998 Lincoln Navigator

1 Answer

At high speed engine temperature is Ok, at low speed or idle it warms up to over half way and the coolant level warning light comes on. There is plenty of coolant, an new water pump and a new thermostat....


is cooling fan coming on?? the coolant level light pertains to a sensor that is in radiator side tank that is notorious for going bad you may have two seperate problems normal temp at high speed tells me the wind passing across radiator is keeping cool when stopped or in traffic as temp increases pcm commands fan to come on if it does,nt you will heat up

Mar 19, 2010 | 2000 Oldsmobile Silhouette

2 Answers

2004 Honda Civic -Code P0122 Throttle Position Sensor Voltage Low


yes, this is the case of a failed throttle body, in which case it needs replaced, the car is getting too much fuel causing the high idle. this needs replaced asap. you could proably find a small independant honda shop that could do the work for less.

May 12, 2009 | 2004 Honda Civic

Not finding what you are looking for?
2003 BMW 745 Li Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...