Question about Cars & Trucks

Open Question

Replace needle packing on Paasche VL airbrush

Am overhauling my old Paasche VL air brush. Purchased the MU-612 Teflon Packintg and Packing nut. My VL had the packing nut, a white washer (?) and a rubber o-ring. Does MU-612 replace the old o-ring with the teflon packing? Or is MU-612 the wrong parts? Do I remove the old o-ring and toss it, using the new parts only???

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: 1996 dodge ram electric window lift

Dealer should be able to order you a kit if not already in stock. Shouldn't be too expensive.

Posted on Nov 29, 2008

  • 1 Answer

SOURCE: 1999 saturn 3 door. Driver

I just replaced my hinge on the passenger side, I will assume you took the old one out by pushing it forward ( it then fell to the floor area and you retrieved it. The new one should align close to the opening and you will need to pull it through with needle nose pliers You will have to practice aligning the threads into the openings. I started on a 45 degree angle, it took me 5 tries before it lined up for the nuts.

Posted on Dec 24, 2008

  • 186 Answers

SOURCE: How do I replace the windshield washer nozzle on

Open Hood,Remove 4 push pin retainers,remove wiper arms.If it's the pass side you will not need to remove wiper arms.Driver's will need arms removed

Posted on May 09, 2009

  • 1 Answer

SOURCE: replace Teflon o-ring on power steering hose

Overdrive light blinks on 96 Aerostar AWD then transmission downshifts hard or will not accelerate

Posted on May 07, 2010

  • 2002 Answers

SOURCE: Why does my PCV valve and grommet keep popping out

It sounds like the line from the PCV valve to the engine is blocked. Double check the valve itself, it should rattle when you shake it. Put it back in but don't connect it to the intake. If it doesn't blow out check for blockages in the line between the PCV valve and the intake or possibly the entry hole inself. Hope this helps.

Posted on Oct 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My fisher minute mount 2 goes up slow but it turns left and right ok


You may have to release some tension in the packing nut on the piston seal, if its too tight it will bind and slow down the piston, try replacing the fluid also with synthetic Mobil 1 Transmission fluid !

Feb 17, 2015 | 2004 Ford F350

1 Answer

Need to remove valve cover on 2000 Camry Toyota


For the four cylinder engine:

  1. Remove and label all electrical wiring, connectors and vacuum hoses necessary to gain removal clearance.
  2. Remove the spark plug wires. Disconnect the PCV hose.
  3. Remove the four nuts and grommets located on top of the cylinder head cover.
  1. Remove the cylinder head cover and the cover gasket from the cylinder head.
  2. Discard the gasket and replace with a new one.
To install:
  1. With a wire brush or gasket scraper, remove all the old gasket material from the cylinder head and the cylinder head cover gasket surfaces.
  2. When the cylinder head surfaces are free and clean, apply beads of sealant to the cylinder head in the locations shown in the accompanying illustrations.
  3. Install the new cylinder head gasket in the cover. Make sure that the gasket seats evenly.
  4. Place the cylinder head cover with the gasket onto the cylinder head.
  5. Install the four grommets and nuts. Uniformly tighten the nuts in several passes to 17 ft. lbs. (23 Nm).
  6. Connect the PCV hose. Connect all removed vacuum hoses, connectors and electrical wiring. Connect the negative battery cable.
  7. Start the engine and inspect for oil leaks.
  8. Repair any leaks as necessary.
For the V-6 (3.0L) engine:
  1. Drain and recycle the engine coolant.
  2. Disconnect the radiator inlet hose.
  3. Disconnect the throttle and accelerator cables.
  4. Remove the air cleaner cap assembly.
  5. Remove the V-bank cover. Use a hexagon wrench to loosen the nuts.
  6. Label and remove all emission control valve hoses. Disconnect any wiring interfering with the valve cover removal.
  7. Remove the air intake chamber. This will gain you access to the back valve cover.
  8. Disconnect the engine wire from the left hand side, No. 3 timing belt cover, rear side and right hand side. Most of the wiring is secured by nuts and or bolts to the body of the vehicle.
  9. Remove the ignition coils, make sure the place them in order on a table so not to mix them up.
  10. Remove the 8 bolts retaining the valve covers and gasket.
  11. Clean the mating area of the valve cover and cylinder heads well. If necessary, scrape any left gasket from either surface.
  12. Apply seal packing to the cylinder heads and place new gaskets into position.
  13. Attach the valve covers. Uniformly tighten the bolts in several passes to 69 inch lbs. (8 Nm).
  14. Install the spark plugs in their proper locations, then place the ignition coils into place and secure.
  15. Attach all engine wiring be sure to secure each harness properly.
  16. Install the air intake chamber. Refer to Fuel System .
  17. Attach all emission hoses and wiring.
  18. Attach the V-bank cover.

Apr 15, 2014 | 2000 Toyota Camry

1 Answer

1992 Dodge Pickup d150 1/2 ton need to know the torque for the front wheel bearings. Thank you


after packing your berrings tighten the nut untell the wheel stops turning , then back the nut off 1 flat ( the nut has 6 flat) wheel should now turn with minamal drag

May 20, 2010 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

I need to install a replacement passenger side mirror on my 2009 chevy truck. this is a manual mirror.


Simple job!!! You just pull off the molding on the inside of the door and you should see some foam rubber packing. Remove that and you will see the nuts that hold the mirror on.

May 11, 2010 | 2009 Chevrolet Impala

1 Answer

I have a 2003 F150 2x4 Supercrew and I'm going to replace the OEM inner and outer front wheel bearings. The truck makes a clicking sound. Can anybody help?


You need to remove the front wheels and then the brake calipers and brackets. Then pop off the hub nut cover. now remove the cotter pin and cap and nut. Now pull off the rotor. Replace whatever parts you plan to replace as well as the rear seal and grease the bearings by packing them. Now reassemble. Tighten the but down about 40 ft lb. Turn the rotor forward and backward now loosen the nut and turn it again. now tighten it back up to the same torque and then back it off 1.4 turn and reassmeble everything else.

Mar 16, 2010 | 2003 Ford F150 Regular Cab

1 Answer

How do i replace an air shock on 2002 bonneville


did this today. went to advance auto parts, purchased monroe replacements air shocks. removed interior trim in trunk to gain access to upper retaining nut on shock. removed 2 retaining nuts at bottom end of shock. attached new air line just as i removed from old shock. inflate, done.

Jul 10, 2009 | 2002 Pontiac Bonneville

2 Answers

Oil cooler line replacement on a 1998 Suburban How to get the lines off of the oil pump


Ok...answer to the question about how to remove the oil cooler lines from the oil filter housing. Once you remove the oil cooler line, either upper or lower (Or both) from the radiator. By the way, I have a 98 GMC suburban 2wd 1500, I was able to just remove the fan housing and unbolt the fan by the four bolts behind the blade, this gave me the room to remove bottom half of fan shroud.
Once lines disconnected from radiator, there is a retainer clip that holds the hose into the nut that is screwed into the oil filter housing. I doused the nuts with WD40, then removed the clip with a screw driver. BE CAREFUL not to let the clips get away from you because it would be a pain to replace. Autozone does not carry nut nor clip!!!!! The hoses are held together by a clip and attached to a bracket as you follow the line toward the front of the truck.
Once clips are removed, tug on each line individually away from the nut screwed into the oil filter housing and wahlaa. Remove the nut and clean all the old teflon tape off with a steel brush and WD40. I reinserted the clip back into the nut and with the new oil line in my hand, pressed the line into the nut with the clip in place. This way you can see how the nut and clip lock the hose in place. Enjoy and I hope this helps you out.
Oh.....use teflon tape on the radiator treads as well as the oil filter housing threads. Install starting at the radiator housing. Snug the bolt (1' 1/16" socket) with the retainer clip inserted.

Apr 23, 2009 | 1998 GMC Suburban

1 Answer

I have to keep replacing the wheel bearings on my 2001 dodge 4x4


are you greasing them (packing) the bearings ?.... also don't over tighten the nut.... put the nut on..... spin the wheel and tighten the nut just enough to allow it to spin

Robert

Jan 01, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Shift concern on 2002 isusu axiom 4l30 e


the problem of the bump is not the trans.....remove the driveshaft...seperate the slip joint....clean out old grease in there and replace grease and re assemble with a new clamp or heavy zip tie.
ford makes a nice teflon grease.....i have done this repair dozenz of times when i worked at an isuzu dealer.
good luck

Aug 15, 2008 | 2002 Isuzu Axiom

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...