Question about 2000 Chrysler Cirrus

1 Answer

Power steering how much fluid does it take i have replaced the 2 lines

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 44,621 Answers

Fill the reservoir to full and start the engine check the fluid level and keep topping up till the level is steady. turn the wheel from lock to lock several times and recheck the oil level. It may take 2 pints . The amount will be in the owners hand book

Posted on Nov 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change power steering fluid hose s do i need 2 bleed still hard 2 steer


Yes but you must first empty rack and replace fluid with new fluid. Old fluid may have broken down and turn into a watery substance. This will not permit proper functioning and may clog new pump and lines.
Hope this helps

Jul 12, 2014 | 2001 GMC Safari

1 Answer

Power steering fluid leak in 99 Toyota Corolla


look for split in the hard line where fluid is leaking. If you see split, change the line only. make sure power steering reservoir is filled and rack and pinion is full (charge with steering wheel left/right motion). You should be able to remove wheel and inside wheel panel to see power steering fluid shooting out of any hole. There is hydraulic pressure on the lines.

Apr 03, 2014 | 2003 Kia Spectra

1 Answer

Power steering leak


with power-steering it could be one of three problems. 1- power steering pump could be going out ( normally with the pump the car will whine but will not normally leak and still hold fluid) 2- a leak in your power steering lines ( and can normally be resolved with new lines or sometimes you may be able to bypass and clamp the leak on the line) 3- you may have busted the O rings in your powersteering pump and that will actually cause the pump to leak

hint- alot of people will tell you that you may also use transmission fluid for power-steering this is true you can its that same thing as power-steering fluid just a different color (but dont put power-steering fluid in a transmission, but at the same time if you plan on replacing the pump i would use transmission fluid due to it being cheaper but it will cause the O rings in the power-steering pump to go out quicker to cause a worse leak) so i would recommend to locate the leak first before using trans fluid due to if its in a line you wont have to replace the pump but if its already the pump this is the cheapest fix until repaired

Jul 05, 2012 | 2000 Ford Taurus

1 Answer

Power steering tank wont hold fluid and leaks out beside driver tire


Sounds like a blown power steering line. To confirm, wipe down all surfaces around the power steering unit including the lines. Replace the power steering fluid and start the engine. While 1 person is inside the truck, have them turn the wheel from side to side while another watches the area around the power steering unit paying very close attention around the lines. The high pressure line is the most common cause for leaking fluid. If there's no crack or kink in the line, the issue may be the fitting itself where it connects to the power steering pump. Both parts are pricey but replacing the high pressure line (about $150 at the dealer) is certainly less expensive than replacing the whole power steering unit itself.

Jul 30, 2011 | 2004 Hyundai Santa Fe

1 Answer

MINI ONE POWER STEERING COMES AND GOES AFTER PUMP REPLACED


2 posible solutions to your problemone is that the rack and pinion unit has a restriction inside. if you remove the return line to the power steering pump and hold over a pan start engine and the pump will push old fluid into the pan instead of recirculating back into the system. you must keep power steering pump full of fluid because the return fluid is being pumped out of the system.also some models have an electric sensor switch on the pressure line that adjusts pressure by how fast the car is going.faster the car travels less power steering pressure

Feb 14, 2011 | 2003 Mini Cooper

1 Answer

The power steering isn't working. The reservoir was empty and I added power steering fluid and it still very hard to steer


YOU HAVE A RUPTURE PRESSURE LINE IF YOU HAVE NO POWER STEERING FLUID IN THE POWER STEERING RESERVOIR.LOCATE LEAK THEN BLEED POWER STEERING SYSTEM BY ADDING POWER STEERING TO RESERVOIR.DONT OVER FILL BY FULL COLD MARK ON POWER STEERING DIP STICK.ADD FLUID TO RESERVOIR WAIT A 2 MINUTES.CHECK FLUID LEVEL AGAIN.WHEN POWER STEERING FLUID LEVEL STOP DROPPING.START ENGINE LET IT RUN FOR 10 SECONDS.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID ADD FLUID IF FLUID LEVEL DROPS. WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE SUPPORT VECHICLE FRONT WHEELS.START ENGINE.NOW TURN STEERING WHEEL GENTLY FROM STOP TO STOP MEANING LEFT TO RIGHT DONT HOLD IN POSITION.LET THE STOP TO STOP BE QUICK.CHECK POWER STEERING FLUID AFTER YOU HAVE TURN STEERING WHEEL ABOUT 7 STOP TO STOP.WHEN FLUID LEVEL STOP DROPPING YOU AT HOT MARK ON DIP STICK BLEEDING PROCESS COMPLETE.TURN OFF ENGINE LOWER VECHICLE BACK TO GROUND WAIT ABOUT 5 MINUTES CHECK YOUR FLUID LEVEL.IF FLUID LOOKS LIKE A TAN COLOR.YOUR POWER STEERING SYSTEM FULL OF AIR.TURN OFF VECHICLE LET VECHICLE SET A LONG WHILE TO AIR BUBBLES SETTLE DOWN LOOK FOR LEAKS AROUND POWER STEERING PUMP FRONT SEAL AND CHECK FOR LEAKS AROUND POWER STEERING LINES.

Dec 01, 2010 | 1999 Oldsmobile Alero

3 Answers

How do you remove the Power Steering Pump and bracket. I have taken off several bolts but it still is not letting loose. Help


3.0L (VIN 3) Engine

f799ffc.gif
Power steering pump mounting detail (3.0L engine)

  1. Disconnect and isolate the negative battery cable.
  2. Remove the accessory drive belt. The belt does not have to be removed from the engine.
  3. Raise and safely support the vehicle.
  4. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  5. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  6. Place a drain pan under the power steering pump. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  7. Remove the accessory drive belt splash shield.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 2 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly out from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 2 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the 2 support bracket mounting bolts to 40ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

3.3L (VIN R) & 3.8L (VIN L) Engines

0b3de97.gif
Rear support bracket mounting detail (3.3 & 3.8L engines)

6764c64.gif
Power steering pump mounting detail (3.3 & 3.8L engines)

  1. Remove and isolate the negative battery cable.
  2. Raise and safely support the vehicle. Place a drain pan under the power steering pump.
  3. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  4. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  5. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  6. Remove the accessory drive belt splash shield.
  7. Remove accessory drive belt.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 3 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 3 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the support bracket mounting bolts to 40 ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. Torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

Nov 03, 2009 | 1997 Chrysler Town & Country

1 Answer

HOW TO REPLACE A POWER STEERING HOSE


FIRST OF ALL YOU HAVE TO REMOVE POWER STEERING FLUID.USING A SUCTION GUN OR LARGE SYRINGE.REMOVE MUCH FLUID AS POSSIBLE.WHEN DONE REMOVING POWER STEERING FLUID.YOU NEED A INLINE WRENCH AND OPEN BOX END WRENCH TO REMOVE THE POWER STEERING HOSE.YOU HAVE TO REMOVE POWER STEERING LINE FROM THE RACK.UNDER THE CAR SAFELY RAISE AND SUPPORT VECHICLE. THEN REMOVE THE TIRE OR WHEEL.THEN REMOVE THE INNER FENDER SPLASH SHIELD.ITS GOING TO BE A TIGHT FIT AND HARD PLACE TO GET YOUR HAND TO REMOVE THE POWER STEERING LINE FROM BOTTOM.WHEN DONE.MAKE SURE NEW POWER STEERING HOSE OR LINE HAS NEW O RINGS.WHEN INSTALLING THE THE NEW STEERING HOSE.WHEN ALL IS DONE BLEED POWER STEERING SYSTEM. FILL UP POWER STEERING PUMP TO CORRECT FLUID LEVEL.THEN LET IT SET FOR 2 MINUTES UNDISTURBED.THEN START THE ENGINE RUN IT FOR 2 TO 3 SECONDS.ONLY CHECK THE RESERVOIR AND ADD MORE FLUID AS NECESSARY.REPEAT THE OPERATION UNTIL THE FLUID LEVEL REMAIN CONSTANT.NOW RAISE FRONT OF THE CAR UNTIL THE WHEELS CLEAR THE GROUND START THE ENGINE AND INCREASE THE SPEED TO ABOUT 1500 RPM.NOW TURN THE STEERING WHEEL GENTLY FROM STOP TO STOP CHECK THE FLUID LEVEL.LOWER THE VECHICLE TO THE GROUND WITH ENGINE STILL RUNNING MOVE THE CAR FORWARD SUFFICIENTY TO OBTAIN FULL RIGHT LOCK FOLLOWED BY FULL LEFT LOCK BUT DONT HOLD THE SREERING WHEEL FIRMLY AGAINST THE STOPS.RECHECK THE FLUID LEVEL IF THE FLUID IN THE RESERVOIR IS EXTREMELY FOAMY ALLOW THE CAR TO STAND FOR A FEW MINUTES.WITH ENGINE OFF.WHEN JOB IS FINISH. WARNING DONT DRIVE CAR ON ROAD IF YOUR FLUID STILL FOAMY OR POWER STEERING PUMP MAKE NOISES.REBLEED THE SYSTEM AND CHECK FLUID LEVEL AND CHECK FOR LEAKS.DONT DRIVE CAR UNTIL YOU START FEELING NORMAL STEERING.IF YOU HAVE TROUBLE DONT DRIVE.HAVE IT TOWED TO THE NEAREST GARAGE.

Oct 05, 2009 | 1999 Oldsmobile Alero

1 Answer

Subaru impreza 1993 power steering leak


YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Sep 04, 2009 | 1993 Subaru Impreza

1 Answer

Need an digram of 2000 ford focus power steering pump


cfef959.gif
Item Part Number Description 1 - Steering wheel 2 - Steering column 3 - Boot 4 - Tie-rod 5 - Tie-rod end 6 - Steering gear 7 - Steering gear to fluid cooler hose 8 - Fluid cooler 9 - Power steering pressure (PSP) switch 10 - Power steering pump 11 - Fluid supply hose 12 - Fluid reservoir 13 - Pump to steering gear pressure line 14 - Steering gear pinion extension

Jul 30, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...