Question about Cars & Trucks

Open Question

I need a complete abacraya orentation - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Mercedes Benz AC Cycling Switch /Compressor Clutch Won't Engage Completly Spins 1/6 of a complete spin repetedly then stops


You need to have the refrigerant charge level checked, it sounds like it is low. You Need a set of AC pressure gauges to do this testing. If the system has a low charge the pressures will be very low in the low side testing port.

Jun 26, 2012 | Cars & Trucks

1 Answer

Removal and installation of thermostat 2001 dodge dakota


find the big hose coming off of the top of your radiator.

follow it to where it connects to the engine and remove it. (coolant will flow out, let engine cool first)

remove the metal piece that the hose was hooked to, should only be two or three bolts.

your old thermostat will be in there, pay attention to the orentation it is in.

remove it and put your new one in there with a new gasket

reinstall metal pipe and radiator hose

refill radiator with the car running and the heater on defrost HIGH

Jun 24, 2011 | 2001 Dodge Dakota

2 Answers

Im replacing the water pump, timming belt on my 1996 audi a4 v6 2.8, they told me i need an idler roller and a tetioner roller, are those two the same thing? also what is a relay roller?


The idler pulley and the tensioner pulley are different. You will need special tools to do this job. I just completed doing the timing belt on my own 96 Audi A4 Quattro.Do you have a service manual for your car as this will help you alot. The tools you need are listed in the service manual with complete directions to complete the job. There are complete timing belt kits available that include the tools needed. The reason they recommend changing all the components is because it is often one of the components that fails that causes the timing belt to break.

Feb 14, 2011 | 1996 Audi A4

1 Answer

2002 Hyundai Acent 1.5 sohc,need info on cam timming


didnt you mark it before you removed the old belt??

Nov 01, 2009 | 2002 Hyundai Accent

2 Answers

1998 buick regal - where is the orifice tube located


the a/c orfice tube if thats what you want it will either be in the inlet line going into the condenor or it will be the hose from condenser to accumulator

Jul 22, 2009 | 1997 Pontiac Bonneville

1 Answer

Removing audio deck from 2003 Chevy Astro


It is very easy: With parking brake applied, shift to 1st gear, then remove the dash panel that goes around the instrument cluster and the stereo. Once the panel is off, you there is a black tab on both of the side of the unit that you push down, and then pull the unit out.
To install an aftermarket deck, I recommend a specific wiring harness adaptor, that you splice onto the connector included with the new deck - so that you can reinstall the original one if/when you want to sell the vehicle. If you don't, you have to cut the original harness wires, and connect them in the correct orentation (which is tough, as there is about 20 wires!)

The dash panel installs in the same way: shift to 1, then push into place.

Apr 29, 2009 | 2003 Chevrolet Astro

1 Answer

Remove audio deck from 2003 Astro


It is very easy: With parking brake applied, shift to 1st gear, then remove the dash panel that goes around the instrument cluster and the stereo. Once the panel is off, you there is a black tab on both of the side of the unit that you push down, and then pull the unit out.
To install an aftermarket deck, I recommend a specific wiring harness adaptor, that you splice onto the connector included with the new deck - so that you can reinstall the original one if/when you want to sell the vehicle. If you don't, you have to cut the original harness wires, and connect them in the correct orentation (which is tough, as there is about 20 wires!)

Apr 29, 2009 | 2003 Chevrolet Astro

1 Answer

What does it takes for a toyota tacoma 2000 v6 to complete the rediness test, not showing cat and evap been completed. fail smog test because the rediness test is not completed but the emissions levels...


It needs a "drive cycle". Start & run it, highway speeds, and then pull over & idle several times, then do city traffic "stop & go" driving, and then sustained highway speeds again. This completes the readiness thest and satisfys all of the monitors.

Aug 07, 2008 | 1995 Toyota Tacoma

2 Answers

Which engine fits a del sol honda 1993


Anything that is OBD 1 or newer if you want it to be legal, here are the most common options and the basic requirements. 1. B16A2/3: Completely bolt-in Swap, VTEC needs to be wired, SIR II, Hasport shift linkage. Del Sol VTEC for the del sol 2. B18B: Completely bolt-in swap, SIR II, Hasport shift linkage. Del Sol VTEC for the del sol 3. B17A: Completely bolt-in swap, cable-hydro transmission kit(not recommended) or hydraulic b-series transmission, VTEC needs to be wired. 4. B18C1: Completely bolt-in swap, VTEC needs to be wired. 5. B18C5: Completely bolt-in swap, OBD conversion, VTEC needs to be wired. 6. B16B: Completely bolt-in swap, OBD conversion, VTEC needs to be wired. 7. H22A: Mount kit required, Hasport shift linkage, VTEC needs to be wired. 8. B16A: Not recommended! Too much work, more costly compared to B16A2/3's. 9. D16Z6: Completely bolt in, VTEC needs to be wired. 10. D16Y8: Completely bolt in, VTEC needs to be wired. If you want to know more check this out - http://hondaswap.com/swap-articles/en gine-swaps-101-a-29052/

May 18, 2008 | 1995 Honda Civic del sol

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...