Question about 1998 Chevrolet K1500

Open Question

Torque spec for steering gear to frame on 1998 k1500

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: Looking for the torque specs for 1998 chevy astro van?

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Posted on Dec 28, 2008

emissionwiz
  • 74945 Answers

SOURCE: torque specs

35-40 foot pounds.

Posted on Mar 06, 2009

Danno5691
  • 17 Answers

SOURCE: I need the torque specs and sequence on a 1998 chevy 350 vortec

Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan

Posted on Apr 25, 2009

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

alicantecoli
  • 22095 Answers

SOURCE: replacing front wheel barings on a 2005 chev

the big one tighten with a big bar and pull it to about 120lbs ,the three smaller ones which i cannot place at the moment but if they are 17mm size heads then about 60 but i always feel them as i do them and never use a torque wrench or a air wrench ,just muscle and 40yrs of feel

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 2008 ford ranger 4x2 front axle


Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

Sep 18, 2014 | 2008 Ford Ranger 2WD

1 Answer

I need the torque specs for a 99 GMC sierra k1500 wheel hub bolts (bearing), and axle nut bolts (front)


hub to steering knuckle 133 ft lbs.

axle nut 155 ft lbs.

lug nuts 140 ft lbs.

May 12, 2011 | 1998 Honda Civic

1 Answer

98 chevy k1500 5.7 , with steering issues. it shoots off to either side when ever it wants too


sound like drag link is worn out or lots of free play in gear box
my bet is on drag link (arm that is bolted to steer box)

May 09, 2011 | 1998 Chevrolet K1500

1 Answer

Need the torque specs for the nuts on the pitman arm stud and the idler arm stud (nuts that hold the linkage on the studs) for a 2003 sierra 1500HD, 4wd, 6.0L, crew cab


pit man arm to steering gear nut 186 ft lbs.

pit man arm to relay rod nut 46 ft lbs.

idler arm to frame nut 73 ft lbs.

idler arm to relay rod nut 46 ft lbs.

May 08, 2011 | 2002 GMC Sierra 1500HD

1 Answer

Need exploded view of power steering gearbox for 1975 ford f-150


REMOVAL & INSTALLATION Fig. 1: Power steering gear installation1980 and Later 85768076.gif
Fig. 2: Intermediate shaft-to-steering column upper joint connection. Remove the pinchbolt shown to disconnect. 1978 Bronco w/power steering shown 85768077.jpg
Fig. 3: Intermediate shaft-to-steering gear joint connection. Remove the pinchbolt shown to disconnect. 1978 Bronco w/power steering shown 85768078.jpg
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Place a drain pan under the gear and disconnect the pressure and return lines. Cap the openings.
  4. Remove the splash shield from the flex coupling.
  5. Disconnect the flex coupling at the gear.
  6. Matchmark and remove the pitman arm from the sector shaft.
  7. Support the steering gear and remove the mounting bolts.
  8. Remove the steering gear. It may be necessary to work it free of the flex coupling. To install:
  9. Place the splash shield on the steering gear lugs.
  10. Slide the flex coupling into place on the steering shaft. Make sure the steering wheel spokes are still horizontal.
  11. Center the steering gear input shaft with the indexing flat facing downward.
  12. Slide the steering gear input shaft into the flex coupling and into place on the frame side rail. Install the flex coupling bolt and torque it to 30 ft. lbs.
  13. Install the gear mounting bolts and torque them to the specifications shown in the Torque Chart at the end of this Section.
  14. Make sure that the wheels are still straight ahead and install the pitman arm. Torque the nut to the specifications shown in the Torque Chart at the end of this Section.
  15. Connect the pressure, then, the return lines. Torque the pressure line to 25 ft. lbs.
  16. Snap the flex coupling shield into place.
  17. Fill the steering reservoir.
  18. Run the engine and turn the steering wheel lock-to-lock several times to expel air. Check for leaks.
prev.gif next.gif

Aug 21, 2010 | Ford F-150 Cars & Trucks

1 Answer

Torque spec for king nut on front spindle of 1999 2 wheel drive dodge dakota?


Unsure as to what you are calling the King nut but here are the torque specs for your front end.

Steering Gear-To-Cradle Bolt...........135 ft pnds
Steering Gear-To-Crossmember Bolt (Dakota 2 WD)..........190 ft pnds
Suspension Cradle Plate To-Cradle Attaching Bolt..............123 ft pnds
Tie Rod End-To-Steering Knuckle Nut Dakota (2WD) .............65 ft pnds
Tie Rod Lock Nut.....................55 ft pnds

Dec 08, 2009 | 1999 Dodge Dakota

1 Answer

I have a 1994 chevy k1500 4x4 and need to change pitman arm


Take the bolts out that attach the steering box to the frame and pivot the box so you can fit the puller on.
Leave the steering shaft and power steering hoses attached.
Mark the new pitman arm and old one in the same place and mark the pitman shaft to keep the same position of the new pit man arm on the old shaft as the old pitman arm.

Sep 06, 2009 | 1994 Chevrolet K1500

1 Answer

Which power steering line goes where on Chevy K1500 gear box?


if the fittings aren't different sizes to help you out, it will be the fitting furthest from the frame, closest to the rad. or engine. all gm trucks are like this.

Dec 10, 2008 | 1996 Chevrolet K1500

1 Answer

What are the torque specs for 1990 dodge dakota front suspension.


call carquest or other parts house and ask them for the torque specs or a front end alignment shop.

Sep 24, 2008 | 1990 Dodge Dakota

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...