Question about Dodge Nitro

1 Answer

Blower motor resistor

No power at blower motor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Follow wires back from motor to resistor, usually in duct work, under or near glove box. Check power in and out , then you'll know.

Posted on Nov 23, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pittmanc
  • 194 Answers

SOURCE: where is the heater blower motor resistor located

if you locate the blower motor the rester is the wire that atachec to blower motor fallow wire till you find a circuit bord this is ur resistor

Posted on Dec 06, 2008

  • 479 Answers

SOURCE: blower motor resistor replacement

the relays are behind the glove box. you have to take the glove box out to have access to the relay for the heating system 

Posted on Dec 10, 2008

chryslertech
  • 115 Answers

SOURCE: Replacing Blower Motor Resistor

  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle (Blower Motor Resistor).
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.80ac4e54.gif

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to test a blower motor resistor to see if it srtill works


there is a resistor for each speed of the motor and it is unusual to blow all resistors as the lower resistors still allow the motor to work. Check for power supply and switch problems and you will need the ignition switch to ne on to get power. Check that you actually have resistors as later models use a module to control blower speeds and this stops the blower if it fails.

May 14, 2014 | 2003 Mitsubishi Galant

1 Answer

2004 canyon no voltage at heater resistor


The resistor provides the ground circuit for the blower motor. So you would need to have power at the blower motor first. Grounding the motor or resistor should make the motor run.
The blower motor gets power from a 30amp fuse which gets power from a relay.

Jan 18, 2014 | 2005 GMC Canyon

1 Answer

Blower motor


I'm showing a blower relay and a resistor used on models with manual ac control.
The blower motor is grounded and the fan switch provides power thru the resistor. So you have a 40amp blower fuse that handles high thru the relay, then a 30amp HVAC fuse that powers the blower thru the fan switch.
Do you not have power from the resistor to the blower motor on the purple wire ?

Jun 26, 2013 | 2003 GMC Envoy

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

3 Answers

The fan doesn't work for the front defroster/heater.


Using a test light, check for power at the blower motor connector. If thereis power there, replace the blower motor. If there is no power there, it could be the blower motor switch or the blower motor resistor. The most common is the blower motor resistor.

Jan 04, 2011 | 2004 Dodge Grand Caravan

1 Answer

The heater / blower in my 1992 dlx has stopped working all fuses ok


Hello hfg.

1. First of all, tap the blower motor gently to see if it starts it. If it does, the brushes or the armature in the motor are worn- replace the motor.
2. If that doesn't help wiggle the connector on the motor and the blower motor resistor. There may be burned or loose connections.
3. If you have power on fuse 7 with the key on, then check for power at the blower motor on the blue white wire. If no power on it you have a break in the wire between the fuse and the blower.
4. Next, check for power on the blue black wire. If there is power there that proves there is continuity through the motor(that's good), if not, replace the motor.
5. The blue black wire then goes to the blower resistor. this resistor gives the different blower speeds.
inside the resistor there is a thermal fuse. It isn't replaceable, only the resistor as an assembly.
If the thermal fuse blows it may indicate that the blower motor is beginning to wear out and draw too many amps. And then you may need to replace both the blower and the resistor.
Check with an ohmmeter across the thermal fuse. If it is open circuit, replace the resistor and the blower. If you don't replace the blower it may blow the new resistor again.
6. If it all checks out to this point, ground the blue/red wire at the resistor. If the blower comes on the problem then becomes the blower switch or a break in the wire to the switch.

Whew.. Hope this helps solve the problem, my fingers are sore..Ha.

Thanks for using FixYa.

KL

Dec 04, 2010 | 1996 Isuzu Rodeo

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

3 Answers

Blower motor resistor, where is it located/


It will be up under the dash on the passenger side near the blower motor. It will have 5 or six wires in its connector

Nov 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Blower motor doesn't work and has no power to it


Check the blower multispeed control resistor pack is not faulty.
The resistor pack is usually located in the air ducting, in the blower fan airflow.
Basically, +12v power is supplied (via fuse) to the fan speed control switch, which then passes via the selected speed control resistor, to the fan motor. Often a interface relay is used to switch the blower motor high current.

Aug 31, 2009 | Dodge Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...