Question about Cars & Trucks
You'd have to find a wiring schematic for your car and locate the wires for the alarm. Either unclip them or cut them. Usually are located in the wiring harness under the dash, above the pedals.
Posted on Nov 22, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Car won't start
Hi, does the alarm shut off when you unlock the passenger door?
If it does not I will give you a test that you can do.
1. disconnect the harness anti-theft control module. (loctaion depend were you live USA next to fuse panel Canadian models above the glove box.) Check the continuity between Light Green/Black wire and Black wire of the anti-theft control module.
2. Continuity should not be there with the door lock in, lock or neutral position. With the door lock in-between lock and neutral position (any door) continuity should be present.
3. If continuity is as specified replace the anti-theft control module. If continuity is not as specified, check operation of the door lock switches.I will add that test at bottom.
4. If the door lock switches are ok check the continuity og LIGHT/BLACK wires between anti-theft control module and door lock switches. Check Continuity of BLACK wire between door lock switches and ground. Continuity should be present if Continuity is not present repair harness or connectors.
5. If Continuity is present, check continuity LIGHT GREEN and BLACK wire of anti-theft control module. Continuity should not be present with trunk lock in lock or neutral position. With trunk lock in-between lock and neutral position, Continuity should be present.
6. If Continuity is as specified replace anti-theft control module. If Continuity is not as specified, check operation of truck lock switches. If necessary replace trunk lock switch.
7. If trunk lock switch is ok, check Continuity og LIGHT GREEN wire between anti-theft control module and trunk lock switch. Check Continuity of BLACK wire between trunk lock switch and ground. Continuity should be present. If Continuity is not present repair harness or connectors.
DOOR LOCK SWITCHES
Disconnect 4-pin door lock switch connect (left and right front doors) With door lock in neutral, full lock or full unlock position, there should be no continuity between any terminal and BLACK wire terminal. Continuity should exist between LIGHT GREEN?WHITE wire and BLACK wire terminals with door lock in-between neutral and full lock position. Continuity should exist between LIGHT GREEN/BLACK wire and BLACK wire terminals with door lock in-between neutral and full unlock positions. If continuity is not as described, replaced door lock switch.
Hope this help its a place to start. let me know if you need anything else.
Posted on Aug 23, 2008
from what it sounds to me is that the alarm is still in anit theft mode
i had this happen to my vehicle
one thing you can try is lock all the doors try and unlock from the passenger side make sure that all the lock come up to the top where they should be
then try it
if that does not work then lift up the rear of the car like it was being towed and it should reset the alarm
short of that you will have to have alarm shop come to you
Posted on Mar 09, 2009
SOURCE: 1997 Jetta GL Alarm
First to turn off the alarm you simply put the key into the drivers door and turn it to unlock the door twice, this is the factory setting to turn off activated Volkswagen alarm. As for the power locks they are air activated, in the trunk near the latch there should be a small electric motor that drives a small air pump with air lines running to all your locks. If this electric motor as worn out your locks will not operate, simple fix replace the motor. I'd try a used one first from a scrap yard to make sure but always check to see if there is power to the motor (you will need another person with a test light to perform this job). Let me know if this works. Vdubs 4-ever !
Posted on Mar 24, 2009
Im no professional but i did recently buy a 93 maxima and i have the same security alarm problem and my powered locks dont work at all. im taking off the door panel today to take a look and see if the alarm sensor is loose or damaged, if it is, ill probably just disconnect it. one thing i have noticed though is that when i hit the lock or unlock button, i hear a faint click from the dashboard area which im assuming is the solenoid on a transistor which would mean that the buttons work but the transistor isnt delivering power. Semi-Solution for Locks: Listen for very quiet click when you lock/unlock doors, if you hear it, uve got major work to do, if you dont, then take apart the door and check the switch connections. Semi-Solution for Alarm: take off the door panel and disconnect the sensor.
Posted on Sep 13, 2009
Tips for a great answer:
Jun 07, 2015 | 1995 Nissan Maxima
Jan 08, 2012 | Nissan Maxima Cars & Trucks
Nov 06, 2011 | 2001 Nissan Maxima
Dec 08, 2010 | 1995 Nissan Maxima
May 06, 2009 | 1993 Nissan Maxima
Mar 22, 2017 | 1995 Nissan Maxima
Jan 06, 2009 | 1988 Nissan Maxima
Jul 05, 2008 | 2000 Nissan Maxima
98 people viewed this question
Usually answered in minutes!