Question about Cars & Trucks

Open Question

Flywheel torque settings

Nissan patrol 4.2td

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Posted on Jul 01, 2008

Ad

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 158 Answers

SOURCE: nissan patrol

1 st stage tension is 59 nm

2 nd stage tension is 108nm

hope this helps you out

Posted on Mar 08, 2009

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

tneubauer
  • 437 Answers

SOURCE: torque spec on 1987 ranger flywheel and cluth plate

15-24 ftlbs.

Source: Mitchell1

Posted on Jan 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need cylinder head torque specs for td42 nissan bus


Here's a link Daniel to the head torque specs,just stroll down page and you will see. Nissan Patrol 4x4 Africa

Jun 22, 2017 | Nissan Cars & Trucks

1 Answer

Towing capacity of Nissan patrol ute tray top 4.2litre manual diesel


Make & Model G.C.M. Braked Trailer Toyota 70 Series 6830 kgs 3500 kgs Nissan Patrol (leaf springs) 6600 kgs 3200 kgs Nissan Patrol (coil springs) 6350 kgs 3200 kgs Beadell Tours 4WD VEHICLE TOWING COMPARISONS

Nov 23, 2016 | Nissan Cars & Trucks

1 Answer

Hi my name is Sarah I just bought a 07/94 GQ NISSAN PATROL and I'm trying to find the engine number so I can register it can u help


No cannot help with that Sarah but if you go to one of the Nissan Patrol Forums and ask I am sure one of the guys there will help you out .
Try this one to start with in the link below and see how you go......................

Nissan Patrol GQ Y60 Ford Maverick

or this one

NissanPatrol com au Forum

Dec 15, 2015 | Nissan Cars & Trucks

1 Answer

What is the torque setting for nissan navara v6 4lt2007 flywheel torque


there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Sep 30, 2015 | Nissan Cars & Trucks

1 Answer

What are the torque specs wor a nissan patrol cylender head


Engine ZD30DDTi
1.Tight to 98-102 Nm
2.Completely loose
3.Tight to 40-44 Nm
4.90 degree angle tight
5.90 degree angle tight

Dec 04, 2013 | 2008 Nissan Patrol 3.0

1 Answer

How to remove ring gear that is stuck on the dual mass flywheel for a patrol


Most ring gears are only shrunk fitted on the fly wheels. REmoval is by simply driving a good cold chisel in between the teeth and cracking the ring . Replacement is by heating the ringear evenly and placing onto the flywheel and letting it cool down. Ensure that any timing marks on the ring gear are in exactly the same place as the one removed. THis heating process may not work if there are sensors in the ring gear for cpu operation Check with service dealer for further info.

Feb 23, 2013 | 1989 Nissan Patrol Wagon

1 Answer

How to replace a fuel filter on a nissan patrol st turbo diesel 2000


not sure what year model it changed over but it either unscrews from the filter housing(and the water sensor in the bottom of it),or you undo a cover and it is in a canister

May 30, 2012 | 1989 Nissan Patrol Wagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13604 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...