Question about Cars & Trucks

Open Question

Vw jetta 3 1996 1.6 cylinder head torque settings

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

Ad
NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 17 Answers

SOURCE: I need the cylinder head torque settings

4 steps, starting from center and doing the normal pattern. 30 ft lbs, then 44 ft lbs.

3rd step 1/4 turn

4th step addional 1/4 turn. Make sure you are using new bolts.

Posted on Aug 07, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my glow plugs in a 2002 jetta 1.9 TDI is there a torque on tightening glow plugs


all 1.9 tdi engines with 8v cylinder heads have glow plugs out side cylinder head, you will find them easy. Torque is from 12 - 14 Nm.

Mar 07, 2014 | 2000 Volkswagen Jetta TDI

1 Answer

1992 vw jetta 1.6 turbo diesel,what is the cylinder head bolt torque spec?


!st thing is get the revised head gasket (used on 1993 up) for this engine from VW or Felpro, always use new head bolts or a repeat failure will occur. Using the revised head gasket here is the procedure to torque the head down, it is done in stages. PLease go to this site and read the whole procedure.

Feb 07, 2012 | 1992 Volkswagen Jetta

1 Answer

TORQUE SETTINGS FOR 1.4 16V 04 VAG ENGINE THEY USED IN SEAT LEON 04 16V 1.4.


Cylinder head instructions

Tightening sequence
tdisline_536.jpg
Cylinder head torque setting for 2004 VW 1.4L 16V fitted in Seat Leon
Renew bolts

Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

May 17, 2011 | 2000 Volkswagen Golf

1 Answer

What is the cyl head torque setting for 05 vw golf 1.4 fsi 16v


Cylinder head instructions

tdisline_358.jpg
Cylinder head torque setting for 2005 VW Golf 1.4 FSI
Renew bolts
Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

Mar 23, 2011 | Volkswagen Golf Cars & Trucks

2 Answers

I have a 2002 VW Jetta and the temperature gauge keeps going up and down... Is this something to worry about ?


Replace the Engine Coolant Temperature (ECT) sensor. ECT sensor is placed in the right back side of the cylinder head on 2002 VW Jetta 1.9 TDI. See picture below:

tdisline_212.jpg

Please do rate my response. Thanks!

Feb 04, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

2000 VW jetta; what is the torque for valve cover and plenum


I briefly looked online and did not see any info direct6ly relating to the torque spec of the cover bolts. I would guess around 15 ft lbs.--not too much--the head is aluminium--best way to go is to walk up to the service counter of the VW dealer and ask him to provide that information. You have the car and they built it!

Apr 09, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...