Question about Cars & Trucks

Open Question

1998 ford ranger code p1132 - Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuckster57
  • 1102 Answers

SOURCE: hi, plz ineed help mi car have codes

P0135 is HO2S-11 (Bank 1 Sensor 1) Heater Circuit Malfunction
P1132 is Lack Of HO2S11 Switches - Sensor Indicates Rich
P0174 is Fuel System Too Lean (Cylinder Bank 2)

Most common cause of P0174 is a dirty MAF. The MAF sensor is in the air inlet tube. clean with ELECTRONICS CLEANER ONLY. Do not use anything else. Clear the code and if it comes back then the MAF sensor may need to be replaced.

P0135 and P1132 are both dealing with the Oxygen sensor in the DRIVERS SIDE exhaust. Replacement of the sensor should clear both the codes.

Posted on Apr 30, 2011

Ad
ZJLimited
  • 17970 Answers

SOURCE: HI. I NEED HELP PLZ

DTC P0300 - Random/Multiple Cylinder Misfire Detected
Basically this means that the the car's computer has detected that not all of the engine's cylinders are firing properly.
A P0300 diagnostic code indicates a random or multiple misfire. If the last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for example, would tell you cylinder number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically which cylinder(s) is/are mis-firing, nor why. The symptoms may include the engine may be harder to start or may stumble / stumble, and/or hesitate.

A code P0300 may mean that one or more of the following has happened:
Faulty spark plugs or wires
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector(s)
Burned exhaust valve
Faulty catalytic converter(s)
Stuck/blocked EGR valve / passages
Faulty camshaft position sensor
Defective computer

About the solutions, if there are no symptoms, the simplest thing to do is to reset the code and see if it comes back. If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.

Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open.


DTC P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

You will likely notice poor fuel economy the illumination of the MIL. A code P0135 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

To solve it, you will need:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)

In this case, it is neither left or right.
- Bank: 1= PS (Passenger Side) / 2= DS (Driver Side)
- Sensor: 1= before cats / 2= after cats

So, on a Ranger, since there is only one sensor after the cats, "sensor 2, bank 1" is the single sensor after the cats. (It may be after all of the cats or after some of them, which is the case on most late model Rangers)

In this picture, the Ranger sensor array corresponds to the second drawing down.
Sensor 2, bank 1 is "HO2S 12" (click image for zoom)...

zjlimited_477.gif

Similarly, spark plug numbering on Fords uses the PS front cylinder for the #1 spark plug. Seems counterintuitive to me but that's Fords convention.


DTC P1132 - Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Rich - Bank 1
DTC P1151 - Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank 2
DTC P1152 - Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Rich - Bank 2
At one time Ford had a TSB for this concern and had a different style drain extension tube so it would direct the water away from the O2 sensor. Make sure the engine is cold and I always removed the inner fenderwell and the Trans. dipstick and tube to get better access to O2 sensor and drain. I suggest check this TSB (Technical Service Bulletin)...

------------------------------------------------------------------------------------------------------------------------------------------------
H40 DTCs P1131, P1151, P1132 AND P1152: UPSTREAM HO2S(S) NOT SWITCHING.
DTCs P1130 AND P1150: FUEL SYSTEM NOT SWITCHING AT FUEL TRIM (RICH OR LEAN)
Diagnostic Trouble Codes (DTCs) P1131 bank 1 (Cylinder 1) and P1151 bank 2 indicate the fuel/air ratio is correcting rich for an overly lean condition. The HO2S voltage is less than 0.45 volt.
DTCs P1132 bank 1 (Cylinder 1) and P1152 bank 2 indicate the fuel/air ratio is correcting lean for an overly rich condition. The HO2S voltage is greater than 0.45 volt.

DTCs P1130 and P1150 indicate the fuel control system has reached maximum compensation for a lean or rich condition and the HO2S is not switching.

DTC/HO2S Reference List
HO2S-11 = DTCs P1131, P1132 and P1130
HO2S-21 = DTCs P1151, P1152 and P1150

Possible causes:
A. Fuel system

Excessive fuel pressure.
Leaking fuel injector(s).
Leaking fuel pressure regulator.
Low fuel pressure or running out of fuel.
Contaminated fuel injector(s)

B. Induction system
Air leaks after the MAF.
Vacuum leaks (vacuum lines and gaskets).
Restricted air inlet.
PCV system.
Fuel purge system.
Improperly seated engine oil dipstick.

C. EGR System
Leaking gasket.
Stuck open EGR valve.
Leaking diaphragm.

D. Base engine
Oil overfill.
Cam timing.
Cylinder compression.
Exhaust leaks before or near the HO2Ss.
Check intake air system for leaks, obstructions and damage.
Check air cleaner element, air cleaner housing for blockage.
Verify integrity of the PCV system.
Check for vacuum leaks.
------------------------------------------------------------------------------------------------------------------------------------------------


DTC P1405 - Differential Pressure Feedback Electronic Sensor Circuit Upstream Hose
A P1405 may still indicate a faulty sensor, it doesn't have to be one of the common fault codes for the sensor to be bad.

Verify both hoses are connected to the DPFE sensor first; Ford has two versions of the sensor commonly used of this generation of modular engines, the first uses a pair of flexible hoses to make the connections from the EGR tube to the sensor. The hose may fail and cause this problem.

The second type of DPFE sensor is stalk-mounted. The two tubes from the EGR tube come up to the sensor and the sensor is just pushed down onto the ends of the tubes and is secured with hardware.

Inspect to see which type you have and whether there are any obvious connection failures. The Differential feedback pressure sensor is located under the hood on the drivers side.

If you locate your EGR valve you will see a tube going from it to your exhaust manifold. You will notice 2 small tubes leading from the large one feeding into a small sensor, this is the DPFE sensor which is throwing your code.

Now, the DPFE "could" be doing its job by telling you the orfice in the tube is plugged, but the DPFE is known to fail on these trucks, but it throws a code P401. It may be a good idea to try a new DPFE sensor before a new EGR tube.


Hope this helps.

Posted on Jul 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 01 ford windstar im getting acode. P1132 can you explain why


P1132
Lack of HO2S-11 Switch, Sensor Indicates Rich A HEGO sensor indicating rich at the end of a test is trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time. I would change both of the upstream (before the catalytic converter) O2 sensors (cylinder bank 0ne and two). 9 times out of ten this is the right guess to fix this code.

Sep 07, 2016 | 2001 Ford Windstar

1 Answer

Ford Taurus 2001 3.0L DOCH OBD 2 Code P1132 andP1152


1132: Leaking fuel injector bank 1
- EGR stuck open
- Engine mechanical condition

1152:
Oxygen sensor rich,
Some vehicles built prior to june 8, 2001 may exhibit a cold engine rough idle and / or a malfunction indicator lamp light with diagnostic trouble codes p0171, p0174, p1132, and p1152 in memory.

Aug 12, 2012 | Cars & Trucks

1 Answer

Codes P1132 @ P1152 what are they and where are they?


Upstream (forward most) oxygen sensor bank two (should be the passenger side). On the exhaust pipe close to the engine. You will have one on each side close to the motor and then one further back.

Jul 26, 2012 | 2000 Ford Ranger SuperCab

1 Answer

Codes p0132 and p1132


p0132 is heated oxygen sensor.......wiring short to positive
and p1132 is heated oxygen sensor not switching, fuel trim, rich mixture.......intake/fuel system injectors MAF sensor, ECT sensor. hope this helps and if you need any more info just ask

Feb 27, 2012 | Ford Explorer Cars & Trucks

1 Answer

What do the following codes mean on my volvo 1999 xc V70 PO1171 PO1132


I'll take it that your Codes are actually P1171 and P1132. The P1171 is: Fuel System Lean during Acceleration and your P1132 is, HO2S (Heated Oxygen Sensor), Circuit shorted to Heater Circuit conditions Bank 1, O2 Sensor 1.

Hope thius helps,

"00 Buck"

Jul 17, 2010 | 1998 Volvo V70

1 Answer

1998 ford ranger idles rough, high then low


does car have engine codes? sounds like your idle air controle valve is sticking. or possible egr problem

Feb 18, 2010 | 1998 Ford Ranger SuperCab

1 Answer

1998 ford ranger wont shift replaced speed sensor has fluid


the speed sensor only affects overdrive, what is the problem exactly, have you run a trouble code tes to see if any shift related codes show up in memory.

Sep 17, 2009 | 1998 Ford Ranger SuperCab

2 Answers

2000 Ford F150 XLT Error Code P1132 and P1152


Error codes P1132 and P1152 indicate O2 sensors reading rich at banks 1 and 2. Change O2 sensors.

Jun 28, 2009 | 2000 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...