Question about 2000 Dodge Durango

Open Question

My blinkers stopped working

I've changed the fuses the flashers the multifunction switch what else can it be

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: no brake lights of blinkers 1990 dodge dynasty

While not likely, it is possible that the light bulbs in both sides are have bad filaments. Turn on ignition key (but don't start engine). Then turn on parking lamps (first detent or "click" on headlamp switch). Walk around car and look for illumination on front parking lamps and rear tail lights. Turn on the right turn signal. Are those (right hand) lamps now changing brilliance? Try the left turn signal in the same manner. Are those (left hand) front and rear lights changing briiliance? Take note of any positions that did NOT change briliance when the turn signals were activated. If NONE changed briliance, you either have a bunch of bad bulbs (unlikely) or a bad flasher (more likely) or a bad turn signal switch (most likely) or perhaps wiring problems (possible if the car has been in a collision or has been "worked on" by some "non-expert" mechanic). Check the action of the emergency flasher control switch located on the steering column (facing up). Pushing it in (down) should result in the button going to two different heights alternately (low, high, low, high). You could just have bad flashers or corroded flasher contacts! Good luck!

Posted on Dec 29, 2008

  • 4 Answers

SOURCE: 1992 Dodge dakota

you have a bulb out or your relay is shot

Posted on Jan 20, 2009

  • 20 Answers

SOURCE: flashers out, module, relay

More than likely to be a flasher relay. If you can locate the relay turn the harzards on and tap the relay with the ennd of a screewdriver. If the hazards start to work for a moment when being hit you know its the relay. If it was a module i would of thourght you would have more electrical problems as modern cars are mutiplexed meaning one module controls lots of different things. hope this helps.

Posted on Jun 01, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 dodge ram 1500 truck

I would think a bad TIPM would be your cause. It controls the body of the truck, and it should send a signal to your cluster as well. You will have to go to the dealer to know for sure, but that is the problem I see at my dealership most of the time when what you describe happens.

Posted on Jul 25, 2009

  • 645 Answers

SOURCE: Turn signals and flashers do not work.

try replacing the four way (hazard) switch if its seperate from the multifunction switch.

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to fix the turn signals on my ford exposition


exposition ? Do you mean expedition ? What year ? The turn signal switch could be bad , bad fuse , turn signal flasher would be a likely culprit . hazard light flasher is different from turn signal flasher .

Mar 16, 2016 | Ford Cars & Trucks

1 Answer

Turn signals not working on my 98 Mustang. Hazards work fine. Already replaced the multifunction switch. Didn't help.


Sounds more like the flasher to me,in the drivers side fuse panel
square box ,looks like a relay , 5 male spade connectors on back.

Mar 24, 2014 | Ford Mustang Cars & Trucks

2 Answers

Blinker lights not working on my dodge ram 1500 1996. Emergency lights work fine and fuse isn't the problem. No arrows turn on when turning the blinkers on but the emergency lights are working fine. Can...


I bet your blinker flasher is not working. Most likely it uses two flashers, my Intrepid did. Somewhere (probably near the fuse box) and likely under the dash you will see a board with relays and stuff plugged in. You will also see two round things, those are most likely the flashers. Swap them if they are the same, then your hazard lights won't but your blinkers will, at least until you get to the store to get a replacement.

Oct 21, 2013 | Cars & Trucks

1 Answer

None of the blinkers work on my 1996 dodge stratus, all bulbs are good as the park lights and flashers work. I have three dead ports in fusebox under hood.


Guessed it's a V6. Trying to sort this out. If setting the headlamp switch to PARK turns on the park filaments of the front park/turn signal lamp and the tail filaments of the rear tail/stop lamps and the separate tail lamps, the park light circuit is good. If 20A fuse 6 in the power distribution center is OK, the combination flasher in the multifunction switch is receiving power. Power is directed to the turn signal lamps by operation of the turn signal/hazard warning switch. If the turn signals are not flashing, the combination switch may have failed or the turn signal flasher part of the combination flasher may have failed. Finally, the hazard warning switch causes the turn signal elements of the front combination park/turn signal lamps and the rear turn lamps to flash.

Sep 14, 2012 | 1996 Dodge Stratus

1 Answer

Need fuse for right side blinker


2001 Mercury Cougar 2.5L SFI HO 6cyl
Right Side Blinker or Turn Signal Lights work with FLASHERS; the Flasher is located top of the steering column, on the multifunction switch.

Hope this helped; good luck.

May 11, 2010 | 2001 Mercury Cougar

1 Answer

Blinkers just stopped working changed fuses didnt work


Do the hazards work? Is it all the blinkers? If so try the flasher fuse otherwise make sure the hazard switch isn't half pressed down. Some cars you can hit the hazard switch just a little so hazards won't come on but neither will the blinkers. If it's just 1 blinker change the bulb

Aug 22, 2009 | 1998 Chevrolet Cavalier

2 Answers

No turn signals or emergency blinkers


Sounds like a multifunction switch, work the emergency flasher button up and down a few times, then attempt to work the turn signals if the signals work then you will need a multifunction switch.

Apr 30, 2009 | 1997 Ford Crown Victoria

2 Answers

2003 F-250 Flashers won't work


I'm leaning towards a bad multifunction switch on your steering column.

symptom chart
  • The turn signal lamps are never on
  • Central junction box (CJB) fuse 27 (15A).
  • Circuitry.
  • Electronic flasher.
  • Multifunction switch.
  • CJB.
  • Go To Pinpoint Test K .



  • The hazard lamps are inoperative
  • Central junction box (CJB) fuse 18 (20A).
  • Circuitry.
  • Electronic flasher.
  • Multifunction switch.
  • CJB.
  • Go To Pinpoint Test M .


Multifunction Switch Removal and Installation
  1. Remove the ignition switch lock cylinder.
    1. Insert the ignition key into the lock cylinder and turn to the RUN position.
    1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
ac0c6df.gif
  1. If equipped, twist the tilt wheel handle and shank and remove.
dbfa19d.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the screws.
    1. Remove the upper and lower steering column shrouds.
26d3c78.gif
  1. Remove the multifunction switch.
    1. Remove the screws.
    1. Disconnect the electrical connectors.
    1. Remove the multifunction switch.
bd46c8c.gif
  1. To install, reverse the removal procedure.
You can do this. You don't even have to remove the steering wheel.
Buy the part at tascafordparts.com for about 35% off too.

Please rate as fixya if this fixes your issue and report back on success. good luck.


Mar 04, 2009 | 2003 Ford F250 Super Duty Crew Cab

3 Answers

Blinkers stopped working


Your F--150 has 2 flashers, emergency and turn signal. Both are mounted on the fuse block under the dash. The turn signal flasher is mounted on the front of the fuse panel, the emergency flasher is mounted on the rear of the fuse panel. so replace the turn signal flasher should solve the problem. Let me know how it goes.

Oct 20, 2008 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...