Question about Chevrolet Silverado 2500HD

Open Question

TORQUE RODS AND MAINS 6.0 CHEV - Silverado 2500HD Chevrolet Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
moparownr
  • 667 Answers

SOURCE: main and rod bearing torque specs

do you have a Haynes Manual or Chilton? if not check your local library, they may have one, the specs are in there

Posted on Mar 31, 2009

Ad
freetek
  • 5568 Answers

SOURCE: need torque specs 1988 Chevy silverado for main bearings and rod

Those values and most everything else you need for DIY work are contained in the Haynes manual for your vehicle. We have one with each of our vehicles and not only give you the info needed to do repairs yourself but also get an idea of how much work a specific repair should (or shouldn't) cost.
'88 Chevy pickup manual
You can also buy these from auto parts stores for a few dollars less and sometimes on eBay for even less.

Posted on Feb 20, 2010

BCAS1298
  • 3092 Answers

SOURCE: I have a v-6 2000 nissan xterra. What are the

Rod bearing torque

Step 1 - 10-12 ft.lbs
Step 2 - 60-65 Degrees more


Main bearing caps torque

66-74 ft. lbs

d6bcc92.gif

Posted on Jul 02, 2010

jturcotte
  • 8531 Answers

SOURCE: yes i have a 00

main bearing cap bolts: tighten them in three steps, in sequence, to 67-74 ft. lbs. (90-100 Nm).

rods: Lubricate the threads with new engine oil and install the nuts, using the following procedure:

  1. Tighten the nuts to 10-12 ft. lbs. (14-16 Nm).
  2. Using a torque angle meter, tighten the nuts an additional 60-65°. If a torque angle meter is not available, tighten the nuts to 28-33 ft. lbs. (38-44 Nm).
  3. f0abf0a.gif

Posted on Oct 05, 2010

  • 58 Answers

SOURCE: I need torque settings for

http://www.torkspec.com/torkspecme.aspx?KI=12-4.3L-262ci-V6 Try this link out. It has various torque specs listed for the 4.3. Be sure to check the years to ensure it is the proper torque spec for your vehicle. Also this may not have all the torque specs you asked for, but I believe it has most of them.

Posted on Jul 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toque specs on a 1971 in line 6 mercury comet's rod bearings and the clearance between the bearing and crankshaft


TORQUE SPEC FOR ROD BEARING BOLTS 19 - 24 FT LBS TORQUE SPEC FOR MAIN BEARING BOLTS 60 - 70 FT LBS, CRANKSHAFT PULLEY BOLT 85 - 100 FT LBS. MAIN BEARING OIL CLEARANCE .0005 - .0022 CONNECTING ROD OIL CLEARANCE .0008 - .0015 / SHAFT END PLAY .004 - .008 / AND ROD SIDE CLEARANCE IS .004 - .011 HOPE THIS HELP THIS INFORMATION I GAVE YOU IS INLINE 6 -200 AND INLINE 6 - 250 ENGINES

Nov 11, 2011 | Cars & Trucks

1 Answer

Torque specs for rod & main brgs for 1994 ford f150, 300 6 cyl fuel inj engine


Main Bearing Cap Torque:
Torque in 2 steps: Step 1: torque to 35 Ft/Lbs Step 2: torque to 70 Ft/Lbs

The Rod Bearing Cap Torque: 45 Foot pounds (Final torque)

Was this what you needed...let me know by your rating of me...thanks!

Sep 17, 2011 | 1994 Ford F150 Styleside Supercab

1 Answer

I need the torque specs for the main bearing and conecting rods for a 2000 chev S-10 W/2.2L engine code (4)


I show the main bearing torque to be 70 ft.lbs.
The rod caps are torqued to 38 ft.lbs.
Best of Luck to you..

Aug 26, 2011 | 2000 Chevrolet S-10

1 Answer

I need torque settings for Chev. 4.3 6 cyl for Rods, Mains, Headbolts, Cylinder Head, and Cam shaft timeing


http://www.torkspec.com/torkspecme.aspx?KI=12-4.3L-262ci-V6 Try this link out. It has various torque specs listed for the 4.3. Be sure to check the years to ensure it is the proper torque spec for your vehicle. Also this may not have all the torque specs you asked for, but I believe it has most of them.

Jul 22, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

Yes i have a 00 model nissian quest van. 3.3 v-6 motor i cant find nobody who knows what the mains and rods torque at. i put a new crankshaft in the van and dont know what to torque the rods and mains at....


main bearing cap bolts: tighten them in three steps, in sequence, to 67-74 ft. lbs. (90-100 Nm).

rods: Lubricate the threads with new engine oil and install the nuts, using the following procedure:
  1. Tighten the nuts to 10-12 ft. lbs. (14-16 Nm).
  2. Using a torque angle meter, tighten the nuts an additional 60-65°. If a torque angle meter is not available, tighten the nuts to 28-33 ft. lbs. (38-44 Nm).
  3. f0abf0a.gif

Oct 05, 2010 | 1994 Nissan Quest

1 Answer

I am looking 4 the torque pressures (ft.lbs) on the main crank bearings, and rod bearings on a 2007 Ford 5.4 3 valve engine??? Gerry..............thank-you


mains - vertical bolts first 30 ft.lb. PLUS 90 degrees
pattern frt

8 7
4 3
2 1
6 5
10 9
side bolts
22 ft. lb plus 90 degrees
pattern frt

7 8
3 4
1 2
5 6
9 10

connecting rod caps cracked type rod-rod and caps must be kept in matched sets, recommend new bolts/nuts, spec is 32 ft lb. plus 105 degrees - torque each item to the correct torque then go back and do the degrees. these are torque to yield bolts and the procedure is very important.

Oct 02, 2010 | Ford F-150 Cars & Trucks

1 Answer

I have a v-6 2000 nissan xterra. What are the


Rod bearing torque

Step 1 - 10-12 ft.lbs
Step 2 - 60-65 Degrees more


Main bearing caps torque

66-74 ft. lbs

d6bcc92.gif

Jul 02, 2010 | 2000 Nissan Xterra

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

4 Answers

Torque specs for 96 Honda Accord 2.2L


the main bearings bolts is to 1st step 30Nm or 22lbs ft and the last step is 75Nm or 54lbs ft in this tighten secuence. 9 3 1 5 7 on the top bolts and........ ........ ........ ... 8 6 2 4 10 botton bolts and the connecting rod 45Nm or 34 lbs ft i hope be help you

Nov 09, 2009 | 1996 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...