Question about Nissan Cars & Trucks
Where is expansion valve located on a nissan 1990 D21
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Please Help ME by Remembering to RATE ME Thank you Vrey Much !!!
This vehicle does not use an external fuel tank switching valve. A supply check valve in the fuel pump assembly opens when the outlet pressure from the energized fuel pump exceeds the opposing check valve spring force.
R E C A L L 1991
THE DUAL FUEL TANK SELECTOR VALVE MAY MALFUNCTION AND CAUSE AN OVERFILL CONDITION IN ONE OF THE FUEL TANKS, RESULTING IN AN OVERFLOW OF FUEL PAST THE FILLER CAP.
THE OVERFLOW OF FUEL PAST THE FILLER CAP CAUSES A FUEL LEAKAGE, WHICH CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.
REPLACE THE DUAL FUEL TANK SELECTOR VALVE.
SYSTEM: FUEL TANK, AUXILIARY.
VANS AND LIGHT TRUCKS WITH DUAL FUEL TANKS PRODUCED IN THE FOLLOWING PERIODS: F150, F250, AND F350 LIGHT TRUCKS BUILT BETWEEN FEBRUARY 28, 1989 AND JULY, 1989; ECONOLINE BUILT BETWEEN FEBRUARY 28, 1989 AND FEBRUARY 11, 1991.
NOTE: FORD HAS AGREED TO RECALL THESE VEHICLES BUT PARTS ARE NOT YET AVAILABLE.PARTS WILL BE AVAILABLE IN DECEMBER 1991. YOU WILL RECEIVE A LETTER FROM FORD ADVISING YOU WHEN TO SCHEDULE AN APPOINTMENT WITH YOUR DEALER TO HAVE THE RECALL WORK PERFORMED. IN THE MEAN TIME, YOU CAN TAKE THE FOLLOWING PRECAUTIONS:FILL EACH TANK TO ONLY 1/3 FULL. IF YOUR VEHICLE LEAKS FUEL OR IF YOU SMELL FUEL, STOP USING THE VEHICLE AND CALL FORD AT (313) 446-4654 AND ADVISE THEM OF YOUR PROBLEM. REFER TO FORD SAFETY RECALL NUMBER 91S39. AN OPERATOR WILL TAKE YOUR NAME AND TELEPHONE NUMBER. A FORD REPRESENTATIVE WILL CALL YOU BACK
Posted on Jan 21, 2009
it should be under the car close to the driver side door. if you can't see it trace it from the fuel tank it should be attached to the fuel line. if you have the repolacement in your hand you will know what you're looking for
Posted on Feb 28, 2010
Grand Am has an expansion valve. Link below has part number and picture of what you are looking for.
Unfortunately, I do not know precisely. But for the most part auto a/c's are all the same. Below I will describe how to find it. I have also included a aguide to determine system operability that may or may not be helpful. Just trace the system with flow path described below the valve has to be between condensor and evaporator.
Reminder the flow for the a/c system is :
1. From the compressor a high pressure (HP) gas goes to the condenser in front of the radiator.
2. From the condenser a HP liquid goes to an expansion device (orifice tube or expansion valve)
3. From expansion device the low pressure gas enters the firewall to the evaporator.
4. From evaporator the low pressure liquid/gas mixture goes through the dryer back to the compressor suction.
Below is a guide to troubleshoot and check system function. This can be done by most folks.
Look at the front of the ac compressor and have someone turn on the ac from inside the car. The front of the pulley(clutch) will spin when turned on.
If it does not spin, the low pressure switch (LPS) is not satisfied. Meaning there is not enough freon in the system to operate the system. Means low freon capicity because of a leak.
The LPS can be jumpered to cause the compressor to run (clutch to engaged) which will draw the freon in the system.
The LPS is usually a two wire sensor on the suction of the compressor. (between evaporator and compressor) Unplug the sensor and install a jumper, this will engage the clutch. Connect a new can of freon
and fill to system capacity.
The capacity of the ac system will be on a label under the hood, do not overfill. Probably about 2 lbs. Local parts stores (Auto Zone and Advance) will have freon with stop leak. This may help the leak. They also make a freon with a UV dye. I always add a single can with dye so that if stop leak does not work I can find the leak in the future.
The system should be filled until suction pressure is about 30 to 38 psi..
Posted on May 31, 2010
Tips for a great answer:
Apr 23, 2017 | Nissan Cars & Trucks
May 20, 2015 | 1998 Nissan Sentra
Feb 09, 2015 | 1993 Nissan Pickup
Sep 22, 2014 | 2008 Nissan Altima
Jun 25, 2012 | 1987 Nissan Pickup
Apr 18, 2010 | 1997 Nissan Pathfinder
Feb 28, 2010 | 1993 Nissan Pickup
Aug 14, 2009 | 1990 Nissan Hardbody King Cab
18 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: