Question about Cars & Trucks

Open Question

Have a starting problem with my 2010 ford fusion some time and fouind out it is an tsb 09-19-1 problem witch i need a new ground wire,pick the ground wire up today but ready dont know where it goes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2006 ford fusion

were is the passenger fuse box

Posted on Dec 23, 2008

Ad
  • 7 Answers

SOURCE: brand new 2010 ford fusion day bought wrench light

Tell the dealer to scan it. We have tons of people come in everyday that just want to know what the light is on for.

Posted on Dec 30, 2009

  • 1 Answer

SOURCE: 4 wire ac delco alternator harness dont know whats what.

http://www.delcoremy.com/pdfs/service_manuals/legacy/1G-290.pdf

Posted on Apr 16, 2010

  • 834 Answers

SOURCE: I picked up a 1988 Ford F150 6cy and the starter solenoid missing

I have provided an image that will assist you and it will connect like so;

1. Connection 1 should have the Pos. (+) battery cable and all of the wires with the large eyelet connectors from the wiring harness connected to it, except for the large cable that runs down to the starter.

2. Connection 2 should only have the large cable going down to the starter connected to it, and there should be no other wire connected there.

3. Connection 3 is the "S" terminal on the starter solenoid, and it is the wire with the small push on connector that is hot only when the key is in the "start" position, usually it is a red wire with a blue stripe, but that is not always the case.

4. Connection 4 is the "I" connection on the starter solenoid and it feeds current back into the ignition, and it is not used on a lot of vehicles after 1981, but if your vehicle has it it will be a small push on connector that will not have any power from it at all, and it will usually be a black wire with a white stripe, but that is not always so.








f2a8a85.jpg

Posted on Jul 10, 2010

  • 1 Answer

SOURCE: Locating the fuse panel in 2010 Ford Fusion

Just give up, try every spot to find the answer and then jus look down by the brake pedal and turn ur head up and u find the fuse panel.

Posted on May 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2009 fusion SEL has data compass error after being rear ended and a shop did repair.


WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION ...

www.fixya.com/cars/t16705785-compass_error_2009_ford_fusion
Feb 21, 2013 - WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION A MESSAGE COMES UP ON MY DASH SAYS COMPASS NO ... SOURCE: I HAVE A2009 FORD FUSION AND IT'S NOT GOING OVER 20 MPH ... Compass data error -- how do i determine my zone-- ... Jan 28, 2010 ' 2007 Ford Edge SEL Plus.

Compass - Ford Fusion Sport - Ford Fusion Forum

www.fordfusionforum.com/topic/9390-compass/
Jan 23, 2013 - Compass - posted in Ford Fusion Sport: 2011 Fusion SEL without navigation screen. Following windshield ... I have recalibrated and reset the compassaccording to the manual instructions (several times) but cannot correct the error. Can anyone help? ... picture of where it is: 2009-08-30_051718_2.gif.

Nov 08, 2015 | 2009 Ford Fusion

1 Answer

Tsb bulletins


Data Base at repair shop or at a dealer

Jul 30, 2014 | 2010 Ford Fusion 2.5

1 Answer

2006 ford fusion fuse box diagram


Here you go , www.bbbind.com you can check it out for yourself . click on technical Information , five rectangular box's will pop up ,click on All TSB's and diagrams for every make and model - FREE .Next page go to the bottom an click on I agree , Next page click on wiring diagrams ,then add your vehicle info . then under system click on electrical distribution , then subsystem fuse panel ! then click search , then click on the blue link . 2006\FM\WRFM06FUS018a .

Feb 09, 2013 | 2006 Ford Fusion

1 Answer

Battery keeps dieing even after changing it twice.jump starts no problem.airbag light stays on aswell.


1st thing to check is where the ground battery wire attaches to the frame of the car - sometimes they get loose and don't make a good connection anymore (if so, just tighten it). You could also look for obvious problems with both battery wires (insulation worn off etc).

On my Civic, the airbag light will go on after the battery is taken out (or dies), and it has to be reset manually. It's easy to do, but at a dealer they'll charge $50-$100 for it. I have no idea if a Ford Fusion is the same way though, so you could check some car forums or just shell out at a dealer where you can be sure they'll fix it.

Sep 28, 2012 | 2010 Ford Fusion SEL

1 Answer

2010 fusion tail lights won't turn off


I suggest check brake switch, underdash, top back side brake pedal or some short/ground there.

Apr 23, 2012 | 2010 Ford Fusion 3.5

1 Answer

Need factory stereo and speaker wiring diagram for '08 Ford Fusion


2008 Ford Fusion Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Blue/Red
Car Radio Accessory Switched 12v+ Wire: Green
Car Radio Ground Wire: Black/Blue
Car Stereo Antenna Trigger Wire: Purple/Black
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Purple
Right Front Speaker Negative Wire (-): White/Orange
Left Rear Speaker Positive Wire (+): Brown/Green
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue

Feb 16, 2012 | 2006 Ford Fusion

2 Answers

Front right side hit . replaced concerter and won't crank over /or start fuel pump doesn'd even come on when key is on ?


ricks63toy, I believe that Ford still uses what is called an inertia switch even in the hybrids. This switch will shut off in the event of an accident shutting off the fuel pump. This is a safety feature built into the vehicle. Seeing that this is a newer vehicle I trust that you still have the manual. If not, the switches are usually located in the trunk. Look on the side walls of the trunk and see if you can locate it. It is usually marked by a sticker. When you find the switch, push the red button down until you hear a click. This will reset the switch and allow power back to your fuel pump. Good luck with this.

May 17, 2011 | 2010 Ford Fusion Hybrid

1 Answer

Just bought a 2008 Ford Fusion with 41k miles. It has a rough idle when I'm stopped at a long light. Should I be concerned?


I would start with changing fuel filter and run a good fuel system cleaner through it for starters. Then a good healthy tune up would be a good consideration - plugs, wires, all fluids & filters. That will give you a good "ground zero" starting point w/your new car.

Mar 10, 2011 | 2008 Ford Fusion

1 Answer

2006 Mercury Milan key stuck in ignition.


There's a TSB published by ford for this condition. It's caused by a binding shifter button.


adobe.gif Printable View (73 KB) TSB
07-14-7
  • KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION
Publication Date: July 6, 2007
FORD: 2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan
This article supersedes TSB 07-2-1 to update the Part List. ISSUE: Some 2006-2007 Fusion, Milan and 2006 Zephyr vehicles built before 9/4/2006 may exhibit a customer concern of the ignition key getting trapped or a shifter slider binding condition. Most of the key trapped conditions are caused due to a binding shifter button which does not allow the pawl to contact the park detect switch.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE If the key will not release from the ignition cylinder lock follow the Key Trapped procedure. On vehicles with a hard-to-shift shift lever into park or slider bunching/binding then follow the Shifter Slider Binding procedure. Key Trapped:
  1. Actuate knob button 5-10 times, observe for binding or sticky condition.
  2. Replace knob assembly if the knob sticks following Workshop Manual (WSM), Section 307-05. NOTE: WHEN REPLACING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR.
Shifter Slider Binding:
  1. If shifter slider is bunched up or binding, replace bezel assembly following WSM, Section 307-05. NOTE: WHEN REPLACING THE BEZEL, CARE NEEDS TO BE TAKEN TO ENSURE THAT THE BRAKE SHIFT INTERLOCK OVERRIDE TAB IS PROPERLY ALIGNED INTO ITS GUIDE. REFER TO FIGURE 1.

    tb8706a.gif
    Figure 1 - Article 07-14-7

    NOTE: WHEN REINSTALLING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR. NOTE: IF OVERRIDE CAP IS DAMAGED DURING REPAIR, IT IS AVAILABLE SEPARATELY.

PART NUMBER PART NAME 6E5Z-7D443-B Bezel Asy-Black w/FNR5 Trans (Fusion-Milan) 6E5Z-7D443-C Bezel Asy-Black w/Aisin F21 Trans (Fusion-Milan) 6H6Z-7D443-A Bezel Asy-Satin Nickel (Zephyr) 6E5Z-7213-C Knob Asy-Black (Fusion-Milan) 6H6Z-7213-A Knob Asy-Charcoal (Zephyr) 6H6Z-7213-B Knob Asy-Charcoal-OD (Zephyr) 6E5Z-7A214-B Override Cap-Black (Fusion-Milan) 6H6Z-7A214-A Override Cap-Satin Nickel (Zephyr) W790088-S901 Screw (2 Req)
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME 071407A 2006-2007 Fusion, Milan And 2006 Zephyr: Replace Knob Assembly, Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.3 Hr. 071407B 2006-2007 Fusion, Milan and 2006 Zephyr: Replace Bezel Assembly Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.4 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 7213 69

NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.

Copyright © 2007 Ford Motor Company
2010&c18=non-tab%20view&c21=07-14-07&c35=tsb%2c07-14-07&s=1366x768&c=32&j=1.3&v=y&k=y&bw=778&bh=347&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 2006 Mercury Milan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...