Question about 1999 Ford Ranger SuperCab

1 Answer

Engine misses and tranny won't shift - 1999 Ford Ranger SuperCab

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,198 Answers

The only thing those problems have in common is the computer. Have a shop check the codes.

Posted on Nov 22, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If the transmission is not shifting, could it be the vaccum modulator?


when was the last time the tranny had a new filter put in with new fluid? if the vacuum module was bad, it would suck all the tranny fluid out of the tranny and into the engine from vacuum and you would be smoking out the tail pipe..

Apr 28, 2015 | Cars & Trucks

1 Answer

Wont shift since ran out of gas


jeep ZJ 94.
no car runs, out of gas,,,, my dream do to this , has failed, 100 times.
HHO failed, and x,z,y.
even the match book cover, showing "turn water to fuel" fails.
im pulling your leg,

running out of fuel , likes to burn up fuel pumps.
they are fuel cooled and fuel lubricated. so dont do that. or $$$$$$$
after you ran it dry, the pump can fail, or have hard time priming.
long cranking to get the full system primed.
is engine running ok?, you failed to say that important fact...so.....
if engines ok?
does car go fast in 1st gear, fact 2 missing.....so...........???
wont shift can mean , tranny slips or wont go to 2nd, 3rd gear.???
which is it? slips? so skips?
or shifts late?
or shift too early.?

id reset the tranny TCM. (brain)

one way is to pull the battery neg cable for 5 min.
wait and put it back
all TCM have learn mode. so drive and teach it how you drive.
newer cars , 1trans, fists vast number of cars so it has an
even harder learn mode (not yours)

tell more get more......????????????????

the FSM is here.
under ZJ.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Mar 09, 2014 | 1994 Jeep Grand Cherokee

1 Answer

5th gear shifter linkage reverse


can i assume you pulled the side plug on tranny and the level
is right there? or gone way down, ever do a 50k service? to it?

M/T tranny (not auto) what engine? the m./t varies by HP of ENGINE.
If its really in 5th ( i bet not)
if the RPM rises fast that is called clutch slip
yes, clutch bad.
if not in 5th actual rpm will rise fast too. slip,
if the other gears wroke like 4th at wide open throttle up hill
gee the chutch is good.
so its not going in to 5th (for lots of reasons)
but 1 reason , is easy.

-AX 4/5/15 transmission
this tranny has a shift tower. (that thing on top that the shifter lever
fits in to)
most tranny that fail to actual shift into gear
is caused by a $1 plastic part failure
so pull the shifter off top of the shift tower.
and look, is the plastic buffer parts all bad, missing, cracked or
destoryed, sure they all end there... all.
i can also remove the shifter, lever.
and shift to 5ht by hand, and see that it DOES.
it either does, or does not.
if it does, the lever parts are bad.
that simple.
see part 61 (im guessing which of 5 tranny it is , )
http://cdn.liveoffroad.com/images/Aisin_AX5_Transmission.jpg

Feb 04, 2014 | 1994 Jeep Wrangler

1 Answer

A750F transmission problem


it might be in limphome mode.?
why not scan it , and see what DTC errors there are, from TCM.
or do all the tests in the FSM for , ON CAR SERVICE.
FSM= factory service manual.
ever try a tranny shop>?

The key to service is doing the steps in the correct order
1: tranny ground trap good. (missing or damaged)
2: scan it.
3: check pump pressure and do the stall tests stated in the fSM.
4: level checks, and if wrong ATF in tranny ?
5: inputs to TCM wrong, ???? ECT, TPS, VSS1,2,3
6: reset TCM and try to see if learn mode , corrects bad shifting.

OTTOMH, there are more. lots more, A/T are complex.
lots to fail.

Jan 29, 2014 | 2010 Toyota FJ Cruiser

1 Answer

New 30rh transmission was installed in my 97 4.0l jeep wrangler and it shifts in all gears except for 3rd! even when it downshifts it goes through all gears but 3rd? please help


why not ask installer that.
btw , the TCM can fail and do that.
that is either a separate module or part of the PCM.

The TCM does all shifting. electronic, shifting it is.
the TCM has scan code errors, did you scan it and the PCM for errors.
if not , why not.????
2>3 shift failure.

even a loose or corroded , trans wired connector can fail.
or the tranny ground strap is missing.
saw a guy replace a tranny 3 times. and all 3 times failed.
he never knew the trans must be grounded perfectly .
his was missing, others simply broken, others rotted away.

what we do is make sure the TCM is sending the correct
voltage single 0v.12v, etc. to the transmission solenoids.
if not, the TCM is bad, or is in limphome. or inputs wrong.

TCM have what is called limphome that can skip gears.
my 4speed skips 2nd , in limp, by DESIGN !
all this is covered in the FSM, why not read it.
or look at alldata.com it's there too.

i also have a switch box, i made., that attaches to the tranny
allowing me to make a manual transmission,
if that works the tranny is good.

the TCM will in fact mess up if its inputs are wrong
just like all computers do.
inputs are, TPS, VSS1 , VSS2, engine heat. shift selector switch PRNDL , and others.
The TCM shifts by the state of inputs. period

one cool thing, some cars pre 98, or so
the TCM is separate box. and with it unplugged
the shifter is now a manual transmission car. (for test or?)
have friends driving like this for 3 years.

Aug 04, 2013 | Jeep Cars & Trucks

1 Answer

Not shifting


Any transmission trouble code will put the trans in second gear
and it won\'t shift.
Key on-off-on-off-on without starting the engine will illuminate
the check engine light .It will flash out the codes.Should see a 55
code ,5 flashes,a pause then 5 more. Any codes other than 12 and
55 need recorded for further diagnnosis.
I was thinking that turning the key on and opening the throttle wide
open 4 times within 5 seconds (engine off)clears tranny codes,not sure about that tho. You might try it then drive it and see if it shifts,although
as soon as the malfunction happens again it will go back into limp mode.
Tranny slipping or a slow shift or converter lock up malfunction along
with many other things will trigger this.

Mar 16, 2013 | 1999 Plymouth Grand Voyager

2 Answers

Speedometer stopped,trany won`t shfit. whats wrong?


Check your speed sensor. located on the tranny. AT tranny wont shift if you have a bad speed sensor.

Jul 10, 2009 | 1995 Dodge Caravan

1 Answer

High idol all the time& tranny problems


Check for vacuum leaks on the high idol. You have a speed sensor or wiring issue with the tranny. Will need to be checked somewhere with a computer to know for sure on the tranny.

Jun 08, 2009 | 1994 Chrysler Concorde

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...