Question about Chevrolet Cars & Trucks

1 Answer

Rear Axle Assembly Diagram

NEED A DIAGRAM TO REPLACE AXLE BEARING IN REAR END OF 2000 TAHOE 4 BY 4

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 46 Answers

Here is a video... Don't mind the crazy dude.

http://www.youtube.com/watch?v=qJ74nxQyZR0&list=UUTEIouUq1i8T-ft9X83A6-Q&index=4

Posted on Nov 22, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: rear axle bearing replacement


REAR WHEEL BEARING/ HUB

Removal Procedure

  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Posted on Feb 22, 2009

  • 34 Answers

SOURCE: How do you replace the rear end on a 1996 Chevrolet cavalier

if your doin it yourself buy a repair manual

Posted on May 06, 2009

  • 102 Answers

SOURCE: can't get left rear axle out to replace bearing

you must remove the cover on the rear end, remove the 5/16" bolt on center carrier, push the pin that the bolt whent through out, thenp push the axle in, a c clip will fall out of the carrier then axle may be removed,

Posted on May 26, 2009

Gozer
  • 435 Answers

SOURCE: looking for repair manual or rear end diagram for

A free solution is to go the Public Library, more than likely they'll have a Chiltons manual. This will show you how to make your repair.

Posted on Jun 08, 2010

  • 5370 Answers

SOURCE: need to replace rear wheel

It requires a special tool to remove and refit the bearing from hub assembly.Also if its not coming out ,then in some cases the hub has to be replaced. The new hub comes with bearings. Click this link directly to see the exploded diagram and procedure to remove and replace parts in 2003 Toyota highlander:-- http://technoanswers.blogspot.com/2011/02/2003-toyota-highlander-rear-wheel.html -------------- Check out.Keep updated.Thanks.Helpmech.

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I hit the curb realy bad in an accident, my rear right side rim wabbles , I replaced the rim thinking it was jst the rim,!But I think its the axle!,shld I replace the whole rear end?


I dont know whar kind of vehicle or how many miles on it but if its rear wheel drive you can replace either. the rear end will cost more than an axle but if it has alot of miles on it plus you dont know about the rest of the componenents inside do the whole thing

Apr 01, 2015 | Cars & Trucks

1 Answer

How to replace a rear axle bearing


That's a big job that requires a lot of shop tools. You'll need at least a 2 ton floor press to get the bearing off the axle once you have it off the car. To get it off the car you'll need to take the cover off the rear end exposing the gears. Don't forget to put a drain pan under it before you remove the bolts. There is a screw that holds the horseshoe clamp on the end of the axle. You must remove this or the axle won't come out. Next, at the wheel end of the axle there are 4 bolts that hold the bearing cover on. Take them off and try pulling on the axle. If it won' come off , you'll need a puller to get it off. Using the floor press, support the bearing and push the axle off the bearing. Do the opposite to push the bearing on and reinstall everything.

Aug 03, 2014 | 1996 Pontiac Firebird

1 Answer

Ford f150 xlt rear wheel bearing diagram


doesnt say what year so try this remove the wheel, brake assembly, and open the rear differential housing cover..take the center spur gears out and push in in the rear axle to remove retaining washer, once removed the axle will come entirely out then remove the axle bearing at the end of the housing,,good luck repost findings

Jan 20, 2013 | Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

2 Answers

Whinning noise in rear end on 99 dodge ram truck. Where can I find information to possibly replace rear bearings??


Not terrible of a job to do. You will have to jack up the rear end and support it on stands and be sure to chock the front wheel so it does not roll forward while jacking it up. Remove the rear wheels and the drum assembly or rotor if disc brakes. Remove the rear differential cover be sure to have a drain pan to catch the fluid that comes out of it. Find the center carrier you will see a pin about 3/4 of inch in diameter going throught the center carrier with a bolt on one end remove the bolt turn chunk until pin comes out. Push the axle in enough to let the c-clip to be removed then pull out the axle. You will then have access to the axle seal and axle bearing. You will probably need a bearing puller with slide hammer to get bearing out. Then put back together.

Sep 24, 2009 | 1999 Dodge Ram

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

1 Answer

How to remove rear axel from ford crown victoria tne axel is loose and making noise leaking fluid i think it neds a new seal


do u mean the axle has "play" when u grab the tire and wiggle it up and down?? if it has play, then it propbably needs an AXLE SEAL AND AXLE BEARING.you will have to carefully inspect the axle itself where the bearing rides for any gouging or damage. THIS JOB requires a decent amount of mechanical skill. 1ST you need to remove the rear end COVER and drain out the gear oil into a drain pan.2ND remove the brake caliper and rotor . 3RD spin the" ring and pinion " around until u see a 5/16 bolt that passes thru from the pass. side to the drivers side. u have to remove this bolt. u will need to "hold "the gears from turning in order to break loose this bolt. 4TH remove this bolt and slide out the large metal ""PIN" that 'divides" the rear end in half. NOW CAREFULLY WITHOUT TURNING THE REAR END SPIDER GEARS,PUSH IN THE AXLE TOWARDS THE INSIDE SO U CAN REMOVE THE "C-CLIP" AT INNER END OF AXLE. now u can slide out axle and youll be able to replace seal and if needed axle bearing. let me know if u need more info.

Sep 05, 2009 | 2000 Ford Crown Victoria

1 Answer

Need a rear end diagram for 1995 chevy cargo van 2 determine parts needed.Leaking throu tire


if you are leaking gear oil through the tire you need an axle shaft seal there is also a axle bearing there unless it is a full floating axle which means the axle has a flange on the wheel end that bolts on. if you go to the chevy dealership near you go to parts and they can print you out a break down of the axle according to your vin number on the van

Aug 24, 2009 | 1995 Chevrolet Cargo

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...