Question about 2003 Chevrolet Tracker

Open Question

How do i change the ignition switch in my 2003 Chevy Tracker

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: how do i change spark plugs on a 2003 chevy tracker?

I don't know if your vehicle is a 4 cylinder or 6 cylinder. This will make a difference in the # of cylinders as well as the placement. If it is the 4 c ylinder when you open the hood it says at Autozone.com that the spark plugs are on the front of the motor lined up 1-4. If it is the 6 cylinder then you will have 3 at the front of the motor and 3 at the back of the motor. Regardless it is the same concept. I don't know for this particular vehicle, but it is possible you may have to remove a large plastic engine covering in order to access the spark plugs. What I recommend is to replace the spark plug wires at the same time as the plugs. For all my vehicles I use NGK plugs and NAPA auto parts has the best plug wires I have used - Belden Maxx. Prior to starting you will want to check the "GAP" on each new spark plug. Using a spark plug gap tool available at parts places for about $1. Take the new plug and the non-porcelin end (the end that has the arc) insert the arc into the gap tool at the lowest end and slide the plug around until you reach the corresponding "GAP". For this vehicle it should be .44" (I checked on Autozone's website but you may want to check to be sure. At some of the part's places they may tell you that you don't have to check the gap, but believe me you alway's should. I just did a car where they insisted that I didn't need to check the gap and each plug was not gapped properly. The Arc on the plug has to be specific for your vehicle or you will have too much spark or not enough. After gapping the new plugs you are ready to start. Somewhere on the side of the motor you should see either 4 or 6 wires/cables branching out to the cylinders. Starting with whichever you prefer (do only one at a time to avoid confusion) trace the wire/cable to the cylinder and where it goes to the cylinder a "boot" covers the spark plug. Twist the boot until it comes off . If you are going to replace the plug wires take that one off and match it up to your new set (They will be different lengths). You will need a ratchet and a spark plug socket (available at parts places) The spark plug socket has rubber on the inside to protect the porcelin of the spark plug, and to provide grip. You may or may not need a small extension. Place the spark plug socket over the end of the spark plug and apply pressure until the spark plug begins to loosen. You may have to apply quite a bit of pressure if they are in there tight. Once it is loosened take the old plug out, and place the new plug in the spark plug socket. Don't use the ratchet at this point, just begin to thread the plug in by hand once it is in there as much as you can get it, tighten it down with the ratchet making sure not to over-tighten. Do the other cylinders in the same manner.

Posted on Mar 04, 2009

Ad
  • 84 Answers

SOURCE: Power Light 2003 Chevy Tracker

altenator problems

Posted on May 05, 2009

  • 1 Answer

SOURCE: Replaced ignition switch 2003 chevy impala and car will not start

After you replace the ignition switch turn the key to start the car and release leave the key were it stops after trying to start wait 10 minutes until security light goes out turn key to full off position then repeat the above procedure two more times for a total of three on the 3rd attempt to start car wait for light to go out then turn key to full off positoion wait 10 seconds then try to start car body control module should learn new pass code and the car should start.
Big john, J@J Automotive

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Best way to get a new key for 2002 chevy tracker


Ignition key is different from the door key. Dealer can make a key using the VIN# otherwise you will have Anti-Theft problems.

May 27, 2017 | Cars & Trucks

1 Answer

2003 chevy tracker, changed temp gauge, water pump head gasket and still goes up towards the red if I do not have the heat on high.


IF you have a viscous fan hub then replace it . Is the thermostat in the correct way. Have a flow test done on the radiator cores as they may be blocked.. Check ignition timing position.

Oct 30, 2013 | Chevrolet Tracker Cars & Trucks

1 Answer

2003 chevy tracker 2.5 v6 maf sensor voltage, ignition on voltage and running voltage? theres 3 wires one positive, two neg.


No the three wires are 1 battery voltage 1 reference voltage 5 volts 1 ground. these sensors read in Hertz so a low reading would indicate a leak in the piping. Low voltage could be due to a dirty sensor computer measures the burn off of the hot wire which has been contaminated by dirt or K & N air filter cleaner. The number one seller of mass air flow sensors.

Oct 26, 2013 | 2003 Chevrolet Tracker

1 Answer

2003 chevy tracker radiator hose sprang leak. replaced hose not engine is overheating and no heat. what could the problem be?


it actually sounds like you dont have enough coolant.if coolant level is full,try changing the thermostat.

Jan 17, 2010 | 2003 Chevrolet Tracker

1 Answer

'03 chevy tracker. no heat. scent of antifreeze


You need to have the cooling system/heater core tested for leaking. Those symptoms sound like the heater core has failed.

Jan 07, 2010 | 2003 Chevrolet Tracker

2 Answers

Power Light 2003 Chevy Tracker


The power light, seperate from the check engine light, is usually a transmission code. Have the vehicle scanned with a code reader so you can isolate the issue.

May 05, 2009 | 2003 Chevrolet Tracker

2 Answers

Van keeps running after turning off ignition and removing key


need to check the engine timing and to make sure you have the right octune of fuel in your car.

Apr 09, 2009 | 1984 Chevrolet Chevy

1 Answer

Fuel pump relay


Fuel pump in back in the gas tank.

May 29, 2008 | 2003 Chevrolet Tracker

Not finding what you are looking for?
2003 Chevrolet Tracker Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...