Question about 2004 Suzuki Verona

1 Answer

Brake switch for transmission stays on all the time

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

No such Ani-mule , tell the symptoms
reverse back up lamps out? how many
brake lamps out, how many ?
or stuck on?
the transmission switch on all A/T is on the right side of the A/T box.
its this very expensive (suz blues) switch.
the reverse switch is part of this PRNDL switch.
lucky for you both on one page.

Posted on Nov 22, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What happens if brake pedal switch sticks ?

It may not let transmission go into lockup when in high gear.

Apr 13, 2017 | Oldsmobile Cars & Trucks

1 Answer

My 1996 aura tl 2.5 feels like the brakes are applied around 20 to 30 mmph when I let off the gas pedal please advise me if I need to get a new transmission. Also the abs light stays on at all times

Iwould look at the front brakes one or bolth calipars could be sticking probably has to do with the abs problem witch has to do with the transmission problem Youshould have a part called the inter lock switch checked its on the side of the transmission its hooked to the gear shift but the transmission needs to know when the brakes are being applyed so it effects bolth and the computer dosen;t know what to do when this switch is bad so you have brake and transmission problems at the sametime

Nov 19, 2010 | Acura TL Cars & Trucks

1 Answer

46re trans. wont stay in lockout ,only sometimes when it does go in it stays in until you release the accelerator.when the accelerator is reapplied it goes in every time but comes out,in out in out???...

There is a solenoid in the transmission that controlls that. You may just need a transmission fluid and filter change. But the filter sometimes gets sticky if the pressure gets low in the transmission. Check to make sure all your connectors are clean and tight, it is an electronic transmission. Another thing that can wreak havoc with that is the brake switch. If it's worn out the lockout will act irratic and not function normally as will the cruis control. Start with the fluid and filter and then go to the brake light switch. If those don't work. Try a power flush on the the tranny. It may just need the solenoid, but if one is going, change them all. Good luck.

Apr 23, 2010 | 1996 Dodge Ram

3 Answers

Brake light stays on just happened 143000 miles

Check your brake switch as it could be faulty hence causing a close circuit which in turn causes the brake light to stay on.It is normally located at the top of the brake pedal.Hope this helps.

Feb 11, 2010 | 2003 Chevrolet Astro

2 Answers

Rear brake lights stay on all the time


May 10, 2009 | 2004 Audi A6

2 Answers

Ford freestar having cruise control and transmission problems

found the brake petel switch sticky and tapping the pettel a couple of times allowed the cruis light to stay lighted and it worked on mu 2006 freestar.

Feb 16, 2009 | 2006 Ford Freestar

2 Answers

Tail Lights stay on all the time.

under the dashboard on the drivers side. look at the brake pedal lever. there should be a switch attached. push switch in and twist to remove. then pull the button as far out as it will go. while holding brake pedal down reinstall switch. then pull pedal up to top. this will reset the brake light switch. if they stay on still, then just replace the brake light switch.

Jan 19, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer


Brake can stay on for a couple of reason

1- iff someone add power steering liquid in brake system

2- Brake caliper seal broken

3- Brake hose spliting inside and brake stay on

4- Car did't move for a long time and rust installed in brake

5- transmission malfunction good luck

Nov 02, 2008 | 1993 Chevrolet Corsica

1 Answer

'S' Light, Speedometer, and Brake light not working properly

On the brake light does not turn-off, you may want to check the brake switch located at the brake padel. It may have 2 or 3 wire switch so please ensure you buy the right one for replacement.

On the speedometer issue, I guess the speed sensor is faulty. It is located on top of the transmission unit, back side of the engine/transmission.

Oct 04, 2008 | 1991 Honda Accord

Not finding what you are looking for?
2004 Suzuki Verona Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides