Question about 1995 Ford Crown Victoria

1 Answer

Hole in an unidintified hose

I can not identify a hose that has a hole in in. Its under egr? I think

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 90 Answers

Remove the hose and replace it.

Posted on Nov 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the downstream hose located


p1406 is the Delta Pressure Feedback Electrical Sensor This sensor is located in the Exhaust Gas Re circulation system. The DPFE sensor measures the amount of exhaust flow when the EGR valve is open. So locate the egr valve and follow the pipe that has insulation on it there will be 2 pipe nipples on this pipe one of the hoses has fallen off or has a hole in it the code has identified the one closes to the exhaust manifold .

Jul 23, 2014 | 2003 Ford Focus

1 Answer

G20 vacuum line runs to what


look under hood on engine compartment for emission vacuum hose routing it can help you locate vacuum hose location to the egr valve

Oct 27, 2013 | Cars & Trucks

3 Answers

I had a diagnostic test done on my 2000 s type jaguar and the code p1405 came up. can i get any help wit htis


P1405 DPFE Sensor Upstream Hose Off Or Plugged
This is actually going to be real easy. There is a sensor with 2 rubber hoses. It probably has a hole in it. This is a black sensor with 2 screws to hold it in place.

May 20, 2011 | Jaguar S-Type Cars & Trucks

1 Answer

Code p0401


EXHAUST GAS RECIRCULATION EGR SYSTEM INSUFFICIENT FLOW DETECTED.CHECK FOR VACUUM HOSE LEAK OR BLOCKAGE.CHECK WIRING CONNECTION.THE EGR VALVE OR ECM HAS FAILED.CHECK INTAKE PORT WHERE EGR VALVE SET ON.LOOK FOR CARBON BUILT UP IN SMALL HOLE BLOCKING OFF EGR FLOW.CLEAN OUT HOLE WITH A CLOTHES HANGER OR SMALL SCREW DRIVER

Apr 24, 2011 | 1993 Mazda MX-5

1 Answer

Replace egr valve on 3.5 litre 215ci v6 how to?


  • Disconnect the car battery. Locate the EGR valve. You may need to refer to the owner's manual.
  • 2 Unhook the air supply hose, vacuum hose and all electrical connections. You may need the screwdriver for this.
  • 3 Remove the EGR mounting bolts with the socket wrench.
  • 4 Unbolt the EGR valve from the EGR tube with the wrench. Use a wide-mouthed wrench, which works best for this.
  • 5 Look at the EGR valve. If there are holes in the valve, it definitely needs to be replaced. If there are no holes, you may opt to clean it by spraying a half can of carburetor cleaner into the valve. Let it sit, then use a gasket scraper, putty knife, small drill bit or long wood screw to scrape out the buildup in the valve.
  • 6 Install a new gasket and EGR valve if a total replacement is due. Attach all hoses, wiring and bolts that were previously removed.
  • 7 Reconnect the battery and test drive the car.


  • if this helps you please give a good thumbs up rateing thanks have good day

    Dec 28, 2010 | 2005 Chrysler 300

    1 Answer

    Have coolant leak right under egr valve any ideas


    check the heater hoses for breaks or pin holes i do believe the run around the EGR area and can be spraying antifreeze around there also check the water tubing going into the intake manifold for leakage as well

    Jan 23, 2010 | 1998 Nissan Quest

    3 Answers

    1999 FORD EXPEDITION 2WD 4.6L EGR VALVE,EGR CONTROL &EGR POSITION SENSOR REPLACED NO FIX STILL BAD FOW CLEANED HOSES


    Remove the throttle body housing on the top of the intake, it is a 90 degree tunnel like small piece held by 4 small bolts, turn it over and look for two holes, these holes are for the EGR valve flow, they are probably plugged up with carboned crud, clean them out with the tip of a screwdriver if neccessary to remove all the crud, once its clean reinstall it and reset your check engine light, hope this helps, let me know

    Dec 04, 2009 | 2000 Ford Expedition

    1 Answer

    What is a BPT valve and does it effect the E.G.R. valve? Can you check a BPT valve?


    My Nissan truck manual for the same engine does not say what it is or what it does but said how to check it. It said to take the hoses of the valve the top two hoses are likely at the same place and 180 deg from eachother. The last hose connector is perpendicular and at the bottom. It said to plug one of the top holes and apply pressure to the bottom hole while applying pressure to the bottom hole. Then you apply a vacume or suction to the open top hole. If you can pull air then the valve or casing is bad and should be replaced. This manual did not second refer to the E.G.R valve from the BPT. The BPT valve was under the Emissions control section. Once this valve has been checked it said to check the EGR valve connected close by. Similar test but air pressure was supposed to be more resistant or something, but may allow some air flow or something?

    Oct 17, 2009 | 1996 Nissan Pickup

    1 Answer

    1997 Maxima Engine Light Code Sequence?


    Its not the EGR tube that's clogged. Its the intake itself, where EGR bolts to it. There is about a 1/2 inch hole that cloggs and needs to be cleaned out.

    Oct 01, 2008 | 1997 Nissan Maxima

    Not finding what you are looking for?
    1995 Ford Crown Victoria Logo

    Related Topics:

    23 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    79186 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    fordexpert

    Level 3 Expert

    5681 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...