Question about 2009 Kia Rio

1 Answer

The windshield washer will not shoot fluid on to windshield is it the Fuse

Blow air in to lines to clear out is it fuse or motor and where is he fuse located

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

It may not be your fuse, your windshield fluid reservoir has a pump that when you activate the switch it pumps the fluid to spray your windshield. The fuse box should be located in the engine compartment on the left hand side or the right hand side of the engine.

Posted on Nov 21, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wiqi546
  • 1511 Answers

SOURCE: where is the fuse located for the windshield washer motor

Hello and Welcome to Fixya
The fuse is in the engine compartment fuse box. See diagram in the owners manual section 6-11..to find out which one it is, or read the list (provided with amp labeling) on the inside cover to review the fuses there.
Locate the windshield washer fuse accordingly and replace it with the same labeled new fuse.

Do RATE my solution, If this helps you out.
Regards.

Posted on Dec 29, 2009

Testimonial: "thanks"

  • 211 Answers

SOURCE: 2005 Kia Sedona, fuse location for windshield

there should be a diagram inside the lid of fuse boxes there should be 2 boxes one by the drivers left foot up about 10 inches from the floor and the other is under the hood fuses and relays in that one .also your owners manuel has a diagram of each box

Posted on Aug 13, 2010

SOURCE: My 2006 Kia Spectra's windshield

I have the same problem with my '06 Spectra 5. I haven't noticed the knocking sound though. The weird thing is my rear window washer works fine which leads me to believe that the washer pump is still OK but what do I know :D

Posted on Oct 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

2 Answers

Windshield Solvent doesn't spray.Wipers work. I can blow air thru lines.But no spray..any suggestions? 1995 Chevy Luminia


Does the pump motor run when turn windshield spray?
Might be home in line.
Might be wrong fluid(too thick)
Might be wiper fluid motor broken.

Nov 03, 2016 | Cars & Trucks

3 Answers

My windshield washer motor in my 2003 Hyundai Sonata does not make any noise nor dispense any windshield washer fluid when I turn it on, but the wipers do engage


Is your wiper fluid level good?Look for leaks at pump,it's connected to container,also check your hoses leaving pump to windshield,could be loose or binding.

Dec 11, 2012 | Hyundai Motor 2003 Sonata

2 Answers

My front windshield washer fluid is in op. wipers work but fluid doesn't spray. is it electrically connected to the rear windshield washer motor? could it be a fuse? how do I trouble shoot?


no the front is not in power with rear they are seperate. check wire plug (connector) at pump,( i assume pump is mounted on or in reservoir ) with test light for power while a helper depresses the spray switch. check for a blown fuse, check switch, check wiring

Jan 13, 2011 | Ford Expedition Cars & Trucks

2 Answers

My windshield washer fluid won't spray


either your pump is out, or your fuse is blown, or your lines are clogged . check fuse then check lines to make sure they arent clogged somehow, and then look into getting a new pump. take it to autozone and they will look at it with you/for you if you just ask :)

Jan 10, 2011 | 2006 Chevrolet Impala

1 Answer

I have a 2001 Hyundai Elantra GLS four door car and about a month ago the windshield wiper fluid has stopped working. When I pull the wiper ledger in the car to clean the windows, no fluid is coming into...


With the hood up, try to clean your windows. If you hear the washer motor running, you have clogged jets that need to be cleaned. You can use a small, sharp object to try to clean out the jets. If you can access the hoses that go to the jets, you can disconnect them and see if you can blow through them to clear the line or use compressed air.

If the washer pump is not working, I would disconnect the wires going to the pump. Test them using a voltmeter to see if you are getting power to the pump. If you are, it may be time for a new pump. If not check the fuse. If the fuse is good its in the control mechanism. Hope this helps. Good luck!

Mar 11, 2010 | Hyundai Motor 2003 Elantra

1 Answer

Washer Fluid will not spray out onto windshield/windscreen. Is it the motor or should I try a fuse first?


Try removing the hose from the spray nozzle and see if it comes out of the hose if it does, then it's just clogged.. If it does, use an air blow gun on the outside of the nozzle spraying inward to remove the clog. Otherwise start with the fuse, and then try the same thing. If nothing happens, then I'd suggest replacing the washer pump (motor).

Feb 24, 2010 | 2006 Kia Sedona

1 Answer

Can't get the windshield washer to function, is there a fuse somewhere for it? Vehicle is a 1991 Ford F150


take the washer moter for off the washe container and bench test it make sure it work then use a air line and blow out the hose attach to wiper could be the line is block and wont let fluid come thru

Oct 09, 2009 | 1991 Ford F150

1 Answer

Both the front and rear washers are not working, which fuse controls this?


When you attempt to use you washers do you 1 hear a noise and no fluid or 2 if no noise no fluid, skip to 3 If 1 check your reservoir fluid level if full check nozzles for wax- polish blocking opening if clean. trace windshield hose to reservoir pull both end loose and Blow air through if clear push back on.
3 Check fuse panel if not marked wiper/washer and you do not have a manual replace all broken fuses your bound to get it that way

Jul 09, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
2009 Kia Rio Logo

965 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...