Question about Suzuki Sidekick

Open Question

Suzuki x90 clutch pedal is very soft - Sidekick Suzuki Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: clutch pedal real soft

You could have either a failing master or slave cylinder or the hydraulic fluid level is very low which could also be from a leaking master or slave cylinder; check for wet-looking areas around both.
The master is located either inside or under the hood on the firewall; the slave is located on the transmission housing itself.
Until you locate the problem, use neutral gear position when starting so the tranny doesn't drag and load the starter.
After replacing the defective cylinder, be sure to bleed the lines (like when doing brake repairs) to avoid having an ineffective or just spongy pedal again.  

Posted on Jan 18, 2009

  • 186 Answers

SOURCE: Clutch Pedal Very Soft

Air in the system. The shave is between the engine and trans and even a small leak won't show up. Look in the rubber piece on trans with a light and see if you see any fluid. If you see any then the slave is starting to fail.

Posted on Aug 03, 2009

  • 1986 Answers

SOURCE: how to remove door panel on x90

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 880 Answers

SOURCE: Height of Clutch Pedal

It sould engage about 2 1/2 inches from the floor board.

Posted on Mar 09, 2010

  • 5 Answers

SOURCE: Soft clutch pedal

well depends on how much milage on the clutch..I would start with clutch master and slave see if that helps because u have to replace any how.....good luck

Posted on Jun 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there mud runs in on my passenger side of the floorboard in my 1998 Suzuki X90?


possible heater core leak --windshield seal leak or clogged drain

Jul 27, 2017 | Suzuki Cars & Trucks

1 Answer

Gas burning to fast on my 1997 Suzuki x90


a Suzuki Jeep, a Japanese jeep?

high mpg . x90

(CEL glowing all the time?) ever scan it for DTC errors. its not hard.

http://www.fixkick.com/MPG.html

Feb 05, 2014 | Jeep Cars & Trucks

1 Answer

X90 fuse box identification


which one there are 2. ?
lost the operators guide? and x90 is a very rare car.
very hard to get books on it after so long, too.
the engine is the same as the 96 sidekick.
Why not photo them, and post it. no one ever has, it seems.

look here , for x90
http://www.scantool.net/software/alldata-diy-1-month-subscription.html



Jan 17, 2014 | 1996 Suzuki X-90

1 Answer

Clutch problem


How would someone on the internet without the
vehicle to check over- know more than you do?

Jun 21, 2013 | Suzuki Cars & Trucks

1 Answer

Crank shaft sensor on a suzuki x90


allmost thats the problem
sensor should be under the main pully (crank pully)
resistence between the probs are 360 - 460 ohms

May 07, 2010 | 1997 Suzuki X-90

2 Answers

Height of Clutch Pedal


I assume it is a cable operated clutch. If so the adjustment is tightened so that there is about 1/2 to 1" of pedal travel to clutch operation, provided the gears can be selected smoothly.

Mar 09, 2010 | 1987 Suzuki Samurai

1 Answer

How to remove door panel on x90


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Jul 13, 2009 | 1996 Suzuki X-90

1 Answer

Suzuki x90 year 1998 repair manual


sure buy on ebay
search
"geo tracker service manual 1998"
same drive train.

buy suzuki parts from suzuki.
see links on my page for top suppliers.

http://www.kick-fix.com/

May 12, 2009 | 1998 Suzuki X-90

1 Answer

How to adjust the clutch.


you should also check to ensure that the cable is not broken close to the radiator to the front of the engine (had the same problem and after changing the clutch and clutch cover that did not solve the problem it was the cable that was broken)

Albert

Apr 01, 2009 | 1996 Suzuki X-90

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...