Question about Toyota Camry

Open Question

Can u reset the pcm/ecm in a 1994 toyota camry

Like to try a reset to my pcm if its possible

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: Correct Firing Order for 1994 Toyota Camry 2.2L 4 cyl.

1-3-4-2

Posted on Jan 21, 2009

Ad
hotratchet
  • 952 Answers

SOURCE: need to replace the thermostat in a 1994 Toyota Camry

1. Look up along the lower radiator hose. It will plug into a metal tube on the engine side. Follow the metal tube. It goes to a housing. The housing is kind of buried in the driver's side of the engine. There are 2 smaller coolant tubes plugged in above it. You do not need to touch those, although it looks at first glance like you do.
2. Disconnect lower radiator hose at the metal tube.
3. Disconnect fan switches 1 and 2. These are on elecrtical harnesses going to this housing.
4. Disconnect a sensor on the front of the engine, just above the lower hose. I believe this is the knock sensor, but I'm not sure.
5. Now for the fun part. There are 3 bolts holding this housing on. You can see one at the top. There are 2 others underneath it, such that the bolts form a triangle pattern. You will have to get the bottom 2 out by feel (blind). They are 10mm.
6. Also, if you look to the front of the housing, you will note another 10mm bolt on the front holding down a black plastic leg. This is a wiring harness duct. Remove that bolt. Trace back along the duct. There is one more bolt on the driver's side retaining the duct. There is also one on the back of the engine at the firewall / driver's side. Remove these 2 as well.
7. There is a 12mm bolt holding the metal tube from that housing to the driver's side. Remove that bolt.
8. Gently pry the plastic wiring duct toward driver's side, and back toward firewall. You have just enough to get it off of the stud on the thermostat housing.
9. Now you can pull the housing. It will not come all the way out. It will come loose enough to give you just enough clearance to remove the thermostat (barely). Once you remove the thermostat, you have to pass it downward and toward the firewall to fumble it out.
By the way, you will notice that the metal tube is kind of wiggly in the thermostat housiung. This is normal.
10. Pass the new thermostat in the same way you got the old one out. Make sure when you plug it in that it has an air bleed poppet, and that this poppet is facing up.
11. Reassemble by reversing removal. Getting the nuts / bolts back in blind is... fun...
I don't know the torque spec. You can get a torqure wrench in there barely if you get creative with extensions, knuckles, etc. I wouldn't go abouve 8-10 ft-lb.

Posted on May 01, 2009

rockitman187
  • 2559 Answers

SOURCE: How much freon does the 1994 Toyota camry hold?

Refrigerant Type R-134a Amount 30oz
Oil Type PAG-46 amount 8 oz


Please take time to rate this fixya

Posted on May 15, 2009

motorhead427
  • 24 Answers

SOURCE: how to change a rear wheel bearing on a 1994 toyota camry

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

Posted on May 30, 2009

  • 30 Answers

SOURCE: 1994 toyota fuel pump relay

Fuel pump relay is in the engine compartment left side fuse block

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 1994 Toyota Camry. Can you tell me where the cruise control computer is located?


has this issue been professionally diagnosed? a failure in the module may not be the issue..... pull codes from cruise computer(this may be achieved by jumper wire at diag connecter near passengers strut tower_ cruise light on dash will flash two digit code combinations). is there an ABSlight on also? speed sensor original?

25264966-vikm2l1x54dflzjz0fcbcuuu-3-0.gif

Nov 01, 2014 | 1994 Toyota Camry

1 Answer

Have a 94 toyota camry , check engine light comes on when stop at light or car sits at idle. got codes 12 , 22, am very confused !!


Code 12. RPM signal.
Problem area: Loose connection, broken rpm signal wire from distributor to ecm to rpm meter, rpm meter, distributor assembly or ecm defective.
Code 22. Water temperature signal.
Problem area: Loose connection at water temperature sensor connector, broken wire between the sensor and the ecm, defective sensor or ecm.

Aug 25, 2013 | 1994 Toyota Camry

1 Answer

Can i convert a toyota camry engine from fuel injection to carburator


No. That is not worth the effort, as it is so integrated into the car's ECM program, and depending on where you are, it is probably not legal anyway.

Mar 10, 2012 | 1994 Toyota Camry

1 Answer

1994 Toyota Camry V6 LE --how do i install an aftermarket speedometer?


The replacement would have to be the same type at least. If there were no fitting instructions with it then it is hard to say anything at this range.

The Camry speedo is connected to the ECM, and to the speed sensor in the dash. Details here, p 60

http://www.turboninjas.com/camry/be.pdf

Jan 18, 2012 | 1994 Toyota Camry

1 Answer

1994 toyota camry anti-theft reset after changing battery


1994 toyota camry turn over but won't crank radio won't come on anti theft system need to be reset

Oct 01, 2011 | 1994 Toyota Camry

1 Answer

1994 toyota camry turns on for only a few seconds then won't start anymore until spark plugs dry from excessive gas. Timing, ECM,TPS, and injectors have been inspected and/or replacedc accordingly.


it could be that the fuel pressure regulator is faulty & needs replacing, if the fuel pressure is too high the engine may be getting too much fuel.....hope this helps.....cheers.

Apr 11, 2011 | 1994 Toyota Camry

1 Answer

Ecm location and illustration, please


FOr 1994 Toyota Camry 2.2L EFI DOHC 4cyl the Engine Control Computer is located: Front seating area, passenger side, under dash, mounted behind kick panel.

102cb0a.jpg

Components locations-1MZ-FE engine (click for zoom).

I hope helps (remember to rate this).

Oct 09, 2010 | 1994 Toyota Camry

2 Answers

Can I swap the engine from a 1995 Toyota Camry to a 1994; same model, same engine/trans?


ye s95 and 94 have the same engine just make sure they are the same size engine and swap em you wont have to do anything with the computer side. 94, 95 did not have anything run by the PCM such as anti theift training.

Mar 27, 2010 | 1994 Toyota Camry

1 Answer

1994 Toyota Camry - I try to crank my car but the atni theft system will not disable


Have you tried disconnecting battery for 15 minutes to reset computer?

Aug 14, 2009 | 1994 Toyota Camry

1 Answer

98 toyota camry with eng. code po466 help


P0466 EVAP Purge Flow Sensor Circuit Range/Performance


Purge flow sensor is usually in the same line as the canister vent sol. the cv sol. lets the fuel vapors that have build up in the charcoal canister, run up to the engine to get re burned - the purge flow senses the fuel vapor flow and i think, lets the ecm/pcm know how much flow is detected. Most likely the purge flow sensor is shot. if it was a one time fault, after clearing the code, you may have to drive 100-200 miles to reset the complete the drive cycle.

Jun 23, 2009 | 1990 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...