Question about 2006 Ford Expedition

Open Question

Brake caliper retaining clip - 2006 Ford Expedition

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1757 Answers

SOURCE: cant remove the rotor and retainer clip

You will need a large bearing retaining nut socket (1-in drive) about 2 7/16th in or 61/62mm (I got mine at NAPA with a 1/2 in to 1-in drive converter) BUT BEFORE loosening the nut there is a small keeper under the bottom edge the nut at the top (12-oclock) position of the nut. Use a magnet to retrac this and then loosen the large bearing nut. You sometimes have to slightly move the nut "a hair" left or right to remove this bearing keeper. Once the keeper is out the nut will easily come off. The rest is easy. Good Luck!

Posted on Nov 10, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me if it takes special tools to remove the rear brake hub and brake line


No, there are no special tools required beyond everyday hand tools.

Raise the vehicle.
Remove the rear wheel and tire assembly from the vehicle If the vehicle is equipped with rear drum brakes, remove any retainer clips from the wheel mounting studs, then pull the brake drum off the hub and bearing.
If the vehicle is equipped with rear disc brakes perform the following:
Remove the two guide pin bolts securing the front disc brake caliper to the steering knuckle.
Remove the disc brake caliper from the knuckle and brake rotor.
Hang the caliper out of the way using a wire hanger or cord. Do not support the caliper by letting it hang by the hydraulic hose.
Remove any retainer clips from the wheel mounting studs, then pull the brake rotor off the hub and bearing.
Remove the dust cap from the hub and bearing assembly
Remove the retaining nut, then the hub and bearing from the knuckle's spindle

Oct 10, 2010 | 2004 Dodge Neon

1 Answer

Servicing front hubs


Automatic Locking Hub

  1. Shift transfer lever to the ``2H'' position, then move vehicle forward and rearward approximately three feet.
  2. Raise and support vehicle, then remove wheel and tire assemblies.
  3. Disconnect brake hose from caliper.
  4. Remove caliper locking bolt.
  5. Rotate pad assembly upward then remove pad retaining clip and caliper assembly
  6. Remove brake pad support bracket.
  7. Remove hub cap retaining bolts, then the hub cap, Fig. 15.
  8. Remove housing assembly, snap ring and shims.
  9. Remove drive clutch assembly, inner cam and lock washer.
  10. Using tool J-36827 or equivalent, remove hub nut.
  11. Remove hub and disc assembly.Manual Locking Hub

    1. Shift transfer lever to the ``2H'' position and set free wheeling hub into Free position.
    2. Raise and support vehicle, then remove wheel and tire assemblies.
    3. Disconnect brake hose from caliper.
    4. Remove caliper locking bolt.
    5. Rotate pad assembly upward then remove pad retaining clip and caliper assembly
    6. Remove brake pad support bracket.
    7. Remove housing assembly retaining bolts then the housing assembly Fig. 16.
    8. Remove snap ring and shims.
    9. Remove body assembly and lock washer.
    10. Using tool J-36827 or equivalent, remove hub nut.
    11. Remove hub and disc assembly

Jul 02, 2010 | 1991 Isuzu Trooper

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    1 Answer

    How do i change back brakes on 2000 olds bravada same as front


    If the rear is disc...here ya go!

    Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Remove or disconnect the following:
      • 2/3 of the brake fluid from the master cylinder
      • Wheels
    3. Place a C-clamp around the outer pad and caliper; tighten the C-clamp until the piston is fully compressed in the caliper.
      • Top caliper retainer, and rotate caliper away from rotor
      • Inboard pad and retaining spring from the caliper
      • Outboard pad from the caliper
    To install:
    1. Clean and lubricate the sleeves and bushing with silicone lubricant
    2. Install or connect the following:
      • Sleeves and bushings into the caliper
      • Clip the retaining spring onto the inboard pad and install the pad in the caliper
      • Outboard pad into the caliper
      • Caliper in position over the rotor and install the mounting bolts
      • Wheel and tire assemblies
    3. Refill the master cylinder and pump pedal to attain full brake pedal before Road-testing the vehicle.

    May 11, 2010 | 2000 Oldsmobile Bravada

    1 Answer

    How to insall front brake pads on a 2000 Ford Focus


    caliper bolts are 7 mm Torx head.

    SECTION 206-03: Front Disc Brake 2000 Focus Workshop Manual
    REMOVAL AND INSTALLATION Brake Pads Removal
    syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If brake fluid is spilt on the paintwork, the affected area must be immediately washed down with cold water.
    1. Loosen the wheel nuts.
    1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
    1. Remove the wheel.
    1. Detach the brake hose from the support bracket.
    1. Detach the outer brake pad retaining clip.
    1. NOTE: Pull the caliper outwards to release the piston.
      Detach the caliper.
      1. Remove the bolt covers.
      1. Remove the bolts.
    1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Suspend the caliper to prevent load being placed on the brake hose.
      Support the brake calipers.
    1. Lift the outer pad retaining clip over the spring retaining lugs.
    1. Remove the outer brake pad.
    1. Remove the inner brake pad.
    Installation
    1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If the caliper piston is retracted into the housing, brake fluid will be displaced from the master cylinder.
      Fully retract the caliper piston.
    1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
      Install the inner brake pad.
    1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
      Install the outer brake pad.
    1. Push the outer retaining clip over the spring retaining lugs.
    1. Install the caliper.
      1. Install the bolts.
      1. Install the bolt covers.
    1. Install the brake hose onto the support bracket.
    1. Locate the outer pad retaining clip.
    1. Install the wheels.
    1. Check the fluid level in the brake fluid reservoir.

    Jan 18, 2010 | 2000 Ford Focus

    2 Answers

    I can't even think how you would get a c clamp in there? Any other tricks to getting that done cause it's kicking my ****!


    Removal & Installation
    1. Before servicing the vehicle, refer to the precautions section.
    2. Remove or disconnect the following:
      • Wheels
      • Pad retaining clip
      • Cap from the bottom caliper bolt
      • Lower caliper mounting bolt and swing the caliper up
      • Brake pads
    To install:
    1. Press the caliper piston back into the cylinder using tool 49 0221 600C.
    2. Install or connect the following:
      • Outer pad to the mounting support and inner pad to the caliper
      • Caliper. Torque the caliper lower mounting bolt to 19–22 ft. lbs. (25–30 Nm). Install the bolt cap.
      • Retaining clip
      • Wheels
    3. Pump the brake pedal several times to seat the pads.
    6c5d395.gif
    Press the front caliper piston back into the cylinder—Mazda3

    Oct 13, 2009 | 2005 Mazda 3

    1 Answer

    How can i change the rear brakes pads?


    1.Remove the cap from the brake fluid reservoir

    2.Loosen the wheel nuts then raise the vehicle and remove wheel

    3.Push the piston back into the bore to provide room for the new brake pads.A C-clamp can be used to accomplish this As the piston is depressed to the bottom of the caliper bore the fluid in the master cylinder will rise.Make sure is doesnt overflow.If necessary drain off some of the fluid. 4.Before removing anything,spray the disc,and brake pads with brake system cleaner dont use compressed air 5.remove the caliper mounting bolt,the banjo fitting for the brake hose shouldnt be disconnected unless you are removing the caliper or hose replacement

    6.Swing the caliper up and secure the caliper up towards the spring with a piece of wire then remove the lower and upper anti-rattle springs.Remove the outer brake pad and shim then remove the inner brake pad ans shim(s)

    7.Remove and inspect the upper and lower pad retainer clips,the pad retainer clips should fit snugly in the caliper mounting bracket;if they dont,replace them.Apply thin film of high-temperature grease to the retainer

    8.Apply anti-squel compound to the back of pads install the new inner pad and shim(s) make sure the "ears" on the upper and lower ends of the pad are fully engaged with their respective grooves and the pad retainer clips

    9.Install the new outer pad and shim if new pad has no shim take the old shimoff the old pad and install it on the new outer pad.Install the upper and lower anti-rattle springs

    10.Clean off the caliper pin and coat it with high-temperature grease.Lubricate the lower caliper pin with grease too thenswing the caliper down over the disc and new pads (if the piston hits the inner pad depress the piston further into the caliper bore with your c-clamp

    11.Install the mounting bolt and tighten it to the torque specifications (44-63) 99 and earlier models (51-55)00 and later models
    12.Put the wheel back on and tighten lug nuts

    Oct 05, 2009 | 1998 Hyundai Elantra

    1 Answer

    How do i replace the brakes?


    1. Raise vehicle.
    2. Remove front wheel and tire assemblies from vehicle.
    3. Remove the two caliper guide pin bolts. NOTE: Note the positioning of the two rail shims between the knuckle's machined abutments and the brake shoes.
    4. Remove caliper assembly from steering knuckle. Proceed by first rotating top of caliper away from steering knuckle, then lifting caliper off bottom machined abutment on steering knuckle. Take care not to lose the two rail shims.
    5. Hang the caliper off to the side using wire or bungee cord. Do not allow the caliper to be supported by the flexible brake hose. Damage to the flexible brake hose may result.
    6. Remove outboard brake shoe by prying the shoe retaining clip over raised area on caliper. Then slide the brake shoe off the caliper
      1. Pull inboard brake shoe away from piston until retaining clip is free from cavity in piston.
      2. Repeat steps 3. through 7. on opposite side of vehicle to remove that sides brake shoes.

    Sep 28, 2009 | 1999 Dodge Intrepid

    3 Answers

    How do i change the pads and rotors on my 2002 trailblazer ls?



    If you Need Pics/ Illistrations Email @rejakwilson@aol.com


    Brake Pads Replacement - Front

    Removal Procedure

    Caution: Refer to Brake Dust Caution in Service Precautions.

    1. Inspect the brake fluid level in the brake master cylinder reservoir.
    2. If the brake fluid is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding.
    3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove the brake fluid with appropriate tool to the midway point before proceeding.
    4. Raise the vehicle. Refer to Vehicle Lifting.
    5. Remove the tire and wheel assembly.

    1. Compress the front brake caliper piston.
    6.1. Install a large C-clamp over the top of the brake caliper housing and against the back of the outboard brake pad. 6.2. Slowly tighten the C-clamp until the piston pushes into the brake caliper enough to slide the brake caliper off the rotor. 6.3. Remove the C-clamp from the brake caliper.
    1. Remove the lower mounting bolt from the slide pin.
    2. Rotate the brake caliper upward until it stops.
    3. Remove the outboard brake pad.
    4. Remove the inboard brake pad.
    5. Remove the brake pad retaining clips from the brake caliper mounting bracket.
    6. Remove the brake pad retaining clip from the brake caliper.
    7. Remove all foreign material from the brake caliper using denatured alcohol.
    Installation Procedure

    Important: When installing new brake pads, DO NOT reuse the old retaining clips for the brake pad. Use only NEW brake pad retaining clips.


    1. Install the brake pad retaining clips to the brake caliper mounting bracket.
    2. Install the brake pad retaining clip to the brake caliper.
    3. Ensure that the brake pad retaining clip in the brake caliper is properly seated.
    4. Install the inboard brake pad.
    5. Install the outboard brake pad.
    6. Rotate the brake caliper down into position.


    Notice: Refer to Fastener Notice in Service Precautions.

    1. Install the lower brake caliper mounting bolt.
      • Tighten the brake caliper mounting bolt to 51 Nm (38 ft. lbs.) .
    1. Install the tire and wheel assembly.
    2. Lower the vehicle. Refer to Vehicle Lifting.
    3. Fill the brake master cylinder reservoir. Caution: Refer to Firm Brake Pedal Caution in Service Precautions.
    4. Pump the brake pedal slowly and firmly to seat the brake pads.
    5. Burnish the new brake pads.



    blnk_spc.gif

    Jul 24, 2009 | 2004 Chevrolet TrailBlazer

    2 Answers

    Cant get front brake pads to fit


    Installation
    1. s1y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If the caliper piston is retracted into the housing, brake fluid will be displaced from the master cylinder.
      Fully retract the caliper piston.
    1. s1y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
      Install the inner brake pad.
    1. s1y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
    f280846.gif

    2. Fully retract the caliper piston
    68064ba.gif
    3. Install the outer brake pad.

    2875a9a.gif
    1. Push the outer retaining clip over the spring retaining lugs.
    4ce25a7.gif
    1. Install the caliper.
      1. Install the bolts.
      1. Install the bolt covers.
    c7fb3d7.gif
    1. Install the brake hose onto the support bracket.
    1. Locate the outer pad retaining clip.
    1. Install the wheels.
    1. Check the fluid level in the brake fluid reservoir.

    Apr 17, 2009 | 2001 Ford Focus

    Not finding what you are looking for?
    2006 Ford Expedition Logo

    Related Topics:

    28 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...