Question about Cars & Trucks

1 Answer

How do I reconnect the ignition wires on a 195 Toyota 4runner?

The ignition wires under the dash were disconnected to remove an added light that was wired into the ignition. When my brother removed it he couldn't figure out how they go back togather. Do you know which wires go where?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 560 Answers

You need to access a wiring diagram of the car. You might find one online. If you can't, pick up a Chilton or Haynes book for the car. They have wiring diagrams.
Your local library might have them.

Posted on Nov 21, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: I am seeking location of

Disconnect Car Battery
I replaced the ignition switch in my wifes 2000 intrigue. (ignition mounted in front dash). I had to take off the knee bump trim and the trim around the instrument housing and remove the instrument cluster. Leave it connected and just lay it on the dash. You also need to remove the radio to get to one of the screws that hold the ignition switch module. Once you get that loose you can pull it out so you can disconnect the wires going to it.
If you need to replace the ignition module insert the key and turn to accessories, there is a small metal button to push in, then your key and the lock part will fall out to install into your knew ignition module. At that time you can also remove the cruise control cable.
I am not a mechanic and the whole process only took me an hour or so.
I replaced my ignition module to fix the heater and AC operation. It also fixed the cruise control that hadn't worked for a year.

Posted on Jan 30, 2009

  • 40 Answers

SOURCE: how to remove passenger side rear tail light lens on 2008 H3 humr

With the car off. Put the park brake on and put it in reverse. When the light comes on take a test light and see witch wire has power.

Posted on Apr 15, 2009

  • 1 Answer

SOURCE: 1988 4Runner RH Dash Removal

I know this post is a bit older, but... You have to remove the right most vent. --To do this slide a thin, flat screwdriver on the tops and bottoms of the vent to press the spring clips. Behind it is one last bolt (10mm) that holds it on.
Hope it helps sammy

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a vehicle run with a non functioning ECM?


if the check engine lite doesn't work it most likely needs cluster removed and bulb replaced its blown. if the computer is bad it wont run. I wanna say that ecu fuse will clear code from computer but its not main power to it. I would start with the bulb that way you can get code.

Feb 18, 2015 | 1994 Toyota 4Runner

1 Answer

Where is diagnostic connector locationon 1994 toyota base pickup


The check engine light is used to blink out the trouble codes. The diagnostic connector is usually under the hood on driver's side, back near the firewall. Sometimes under the driver's dash. Use a jumper wire and connect terminals TE1 and T1. Then turn key to on, not start, and the check engine light will blink out the trouble codes. If no codes are present, the check engine light will stay on constantly. Remove jumper wire when diagnostics completed. To clear codes after repairs, disconnect the negative battery terminal for one minute, and then reconnect.
This site has Toyota code explanations:

Dec 30, 2013 | Cars & Trucks

1 Answer

Ignition wires under dash disconnected


hi. there cheryl it is dangerous to mess around with the wiring loom
if you are not careful. you could start a fire. my advise is if you dont
know about electrics leave it to the professionals. be safe

Nov 21, 2013 | 1995 Toyota 4Runner

1 Answer

How do I replace the brake light switch on my 1997 toyota tacoma?


The brake light switch is located on a bracket under the dash near the top of the brake pedal arm. To remove switch, disconnect wiring, loosen locknut and unscrew switch. Replacement is reverse procedure. To adjust, screw in switch until operating button is fully depressed by pedal arm, tighten locknut and reconnect wires. Check for correct operation of lights You may have to unscrew switch slightly to get best operation..

Nov 27, 2010 | Toyota Tacoma Cars & Trucks

2 Answers

I changed the battery in my 2001 toyota forerunner and not a few lights on the dash continue to flash., Any answers?


Try disconnecting both poles of the battery and leave it off during the night. Reconnect it. If problem persists you probably need to use a OBD2 diagostics tool/resetter.

Apr 17, 2010 | 2001 Toyota 4Runner

1 Answer

After installing a new starter my 1991 4runner will not start..i think it's the alarm..unplugged the wires under the dash and light for alarm came on although it still won't start...


depends on the alarm system if its a after market alarm you may have to disconnect the battery to reset it thats what i had to do on mine

Jan 12, 2010 | 1991 Toyota 4Runner

1 Answer

I want to replace ignition lock cylinder on my 1998 Toyota 4Runner do I need special tools to do it? or what are the steps to do it? thanks.


You have to remove the plastic cover underneath of the steering wheel, after that the metal shield behind the plastic cover. When you remove the shield you will get access to the ignition lock cylinder. Disconnect the wire harness, remove the cylinder, install a new cylinder. Connect the wire harness, install the shield, install the plastic cover.

PS: Before start write down the code for your stereo (if you have one), disconnect the negative cable from the battery. Be careful when you work around the air bags.

Sep 17, 2009 | 1998 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...