Question about 2003 Ford Mondeo

1 Answer

Rear brake lights not working

The centre brake light works but not side lamps bulbs are ok

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 208 Answers

Break switch above the break are needs to be replaced i think

Posted on Nov 22, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why doesn't passenger side brake light work?


Either your bulb is out or there is a bad connection somewhere. Usually in the socket. Clean up the connections if needed.

Oct 22, 2015 | 2005 Jeep Liberty

3 Answers

2011 ford feista se brake light out on drivers side. Running light and blinker work. Have replaced bulb and socket with same results what do I do now?


Did you try the passenger side brake bulb in the driver side socket (maybe the new lamp is bad)??

If it works, then the problem is either a bad ground connection / wire at / between chassis and the shell of brake lamp socket, or bad 12 volt wire at / between the common passenger 12 volt brake light wire in the harness to the center contact on the brake lamp socket.

My suggestion is if the brake lamp wire is ONLY for brakes - not the directional too, simply add a new wire spliced into the passenger side brake light wire and extend it to the brake light wire closest to the new socket that you recently installed on the driver side. Disconnect the vehicle brake wire from the new socket and wire nut it off or tape it up (so it can't short out if it somehow becomes energized again) and splice this new wire to the new socket.

Test & you're done!

May 21, 2014 | 2011 Ford Fiesta

1 Answer

On my z71 1996 model rear bake lights don't work but the third light works, could it be the brake switch ?


No, it is not the brake lamp switch. If the brake lamp switch was not working, the high mount (3rd) brake lamp would also not function.
Chevrolet trucks are notorious for bad tail lamp circuit boards.

Disconnect the electrical connector from the circuit boards. Check for power at the circuit board connector (with the brake pedal depressed) on each side. The brake/turn lamp circuit for the left side is the YELLOW wire. The brake/turn lamp circuit for the right side is the GREEN wire. If there is power at the connector, check the GROUND (BLACK wires) to make sure they are getting a good ground. If the power and ground circuits are OK at the connector, replace the circuit boards.

NOTE: DORMAN makes a kit that includes circuit boards for both sides it is DORMAN Part Number 70001

If there is no power on the YELLOW and GREEN wires at the circuit board connectors, the most likely cause would be a defective turn signal switch.

Apr 28, 2012 | 1996 Chevrolet K1500

1 Answer

Left rear turn light wont work, bulb and fuses are ok.


Does the left brake light work? (only relevant if your signal and brake light are on a double element bulb in the same lamp assembly). Not relevant if you have an amber t/s light separate from the brake light. If the t/s and brake are in the same lamp housing and the brake light works the wiring is ok and the turn signal switch needs to be checked. If neither work a wire or connector is open circuited; or the ground for the lamp socket is not made. Hope this helps.

Jun 20, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Rear side brake lights won't work after fuses/bulbs replacement


If the high level brake lamp works and the other 2 lamps have good bulbs, then there is a power loss, most propably with the installation. You should go to an auto electrician to see where the break is.
If someone has recently done any work on the electrics, you should recheck. It is not a seperate fusable power supply system or brake switch for the high level brake lamp, it will take its power from the fused system that the other 2 have.
Hope this helps

Oct 04, 2009 | 1998 Land Rover Discovery

1 Answer

Rear brake light function not working


Hi
You may just have a bad earth in wiring on the lighting or your light control modual could be fuilty has any one tested this for you
Paul

Dec 31, 2008 | 1996 Lincoln Town Car

1 Answer

Passenger side tail lamp


could be the socket where you put the bulb or the wire that goes to the socket. there could be no power going to the wire.

tnx 4 using fixya,

drcool

Oct 14, 2008 | 1999 Ford Windstar

1 Answer

Rear Running Lights Out


Check the 10 amp "Tail" fuse. This controls the running lamps.
Note that the rear bulbs are "dual filament" bulbs, and even though the brake lamp feature works, the running light feature in the same bulb can be bad.

Oct 04, 2008 | 2002 Toyota Sienna

Not finding what you are looking for?
2003 Ford Mondeo Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...