Question about Cars & Trucks

1 Answer

What kind of brake fluid is used in a 96 Chrysler cirrus?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

DOT3, so pick your brand (Prestone, Amsoil, Autozone, and etc..)

Posted on Nov 21, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ifixgms
  • 64 Answers

SOURCE: 96 chrysler cirrus 2.4 pouring out oil

going to be hard to see but the sensor for oil pressure is located in the rear somewhere close to the oil filter area. find that sensor bad alot. try that

Posted on Apr 06, 2009

  • 880 Answers

SOURCE: where is thermostat in a 1995 chrysler cirrus LX

A tee is located to the right hand side of the intake manifold, on top you should see the coolant system cap, its silver in color and is about 2-3 inches in diameter. This tee is the thermostat housing, it goes to your radiator and engine block, remove it from the block and you should see the thermostat. Remember when replacing the thermostat, the spring side goes into the block! 2.0L and 2.4L it is under where the upper rad hose hooks to the engine. 2.5L it is under where the lower rad hose hooks to the engine.

Posted on Dec 29, 2009

clifford224
  • 1975 Answers

SOURCE: Spark plug to distributor cap Wiring schematic for

I'm guessing that you have the 6 cyl 2.5 liter engine because the 2.4 liter engine that the Cirrus had for that year I believe had a coil pack. The picture below is for the 2.5. If you need the other just write a reply and I will be notified in my email and I will post it if needed. I hope this helps you and good luck.


clifford224_148.jpg

Posted on Mar 18, 2011

  • 31 Answers

SOURCE: How do I bleed the brakes on my 2000 chrysler

Get a helper. Fill the master cyl reservoir with brake fluid. have helper push brake peddle to the floor and hold it. crack bleeder at the farthest brake caliper from the master cyl. (right rear) close bleeder screw let brake peddle up for about 10 sec. repeat until u get nothing but fluid from bleeder. Don't forget to check reservoir level regularly. If u let it run dry u get to start all over again.

Posted on May 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my 1998 chrysler cirrus shift into gear?


I'm not familiar with YOUR Chrysler, BUT... my brother' father-in-law had a Buick [about 1998 model] that would NOT shift into any gear UNLESS the brake pedal was FULLY DEPRESSED!!!!!

I could move the shift lever into any of the indicator positions, but the transmission would not engage if my foot was not firmly on the brake pedal while selecting a gear position!

Sep 03, 2014 | 1998 Chrysler Cirrus

1 Answer

2000 Chrysler Cirrus LXi 3.6 4 door sedan 4 Disk


check the level of dot 3 oil in the reserves...remember you replaced the lines and air has gotten into it- ti may take a bit to fill caliper..
if this doesnt work there might be a problem with the brakes fluid dispersion- it regulates the amount of fluid to each wheel...

Sep 03, 2013 | 2000 Chrysler Cirrus

1 Answer

How do I bleed the brakes on my 2000 chrysler cirrus?


Get a helper. Fill the master cyl reservoir with brake fluid. have helper push brake peddle to the floor and hold it. crack bleeder at the farthest brake caliper from the master cyl. (right rear) close bleeder screw let brake peddle up for about 10 sec. repeat until u get nothing but fluid from bleeder. Don't forget to check reservoir level regularly. If u let it run dry u get to start all over again.

May 16, 2011 | 2000 Chrysler Cirrus

1 Answer

My brake light is on


I assum you mean the brake light on the dash. That light will come on if the park brake is set even if its partly set. It will also come on if the brake fluid is low. If the brake fluid is low check for leaks or low brake pads but you have to find out why the brake fluid is low.

Dec 03, 2010 | 1998 Chrysler Cirrus

1 Answer

96 Cirrus a/c


could be clutch relay, did he override the relay?

Jun 30, 2009 | 1996 Chrysler Cirrus

1 Answer

96 chrysler cirrus 2.4 pouring out oil


going to be hard to see but the sensor for oil pressure is located in the rear somewhere close to the oil filter area. find that sensor bad alot. try that

Apr 06, 2009 | 1996 Chrysler Cirrus

1 Answer

What type of transmission fluid is used in a 1996 Chrysler Cirrus? I purchased Multi-vehicle ATF, can I use this?


NO YOU SHOULD NOT. YOU MUST ONLY USE ATF +4 AND PERFERABLY MOPAR FLUID. CAN USE CASTROL OR OTHER QUALITY OIL BUT NOT RECOMMENDED. I HAVE THIS VEHICLE AS DAILY DRIVER.

Mar 17, 2009 | 1996 Chrysler Cirrus

1 Answer

New brakes


Still have air inside, because you used gravity feed method.

Jul 17, 2008 | 2000 Chrysler Cirrus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...