Question about Cars & Trucks

2 Answers

Electronic throttle body no responce from it but still can rev up to 2900 rpm

Getting fault code p2113 changed the aps with a new one checked the butterfly on throttle body and there is a click but no response to the position of the gas pedal, there is power in the harness side connector

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 887 Answers

You need to have the throttle position sensor adjusted by the dealer using a tec 2 scanner.

Posted on Nov 22, 2013

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,649 Answers

Need the make model and year and engine size and type.

Posted on Nov 22, 2013

  • 1 more comment 
  • tony walker
    tony walker Nov 22, 2013

    2006 hyundai tucson crdi 2.0l cleaned the electronic throttle body and connections drove with no problem then p2113 code came back,checked throttle body no sound at first,then started to click when ignition turned on,when pedal was pressed down the butterfly never moved in the throttle body,even with engine running,can clear p2113 code engine revs as normal then fault code comes back and then back to running at max 280 - 290 rpm

  • tony walker
    tony walker Nov 22, 2013

    checked inside the throttle body and found that part of the teeth on the half moon cog that is on the butterfly spindle are warn,so it looks like a new throttle body is needed.

  • tony walker
    tony walker Nov 23, 2013

    checked wiring on MAF found a broken wire repaired it, now i have no p2113 fault code rpm normal seems fixed ? ( fingers crossed )

×

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

localwonder
  • 6784 Answers

SOURCE: throttle Pedal Position Sensor Switch A

its just a sensor. you do not have to replace the entire throttle body.

Posted on Mar 16, 2009

ZJLimited
  • 17970 Answers

SOURCE: check engine lite is on,

Your CODE P1276 refer to the Acelerator Pedal Position, Sensor 1 Circuit Range Performance.

Probable cause: Wiring, APP or ECM


GM - P1271 Accelerator Pedal Position Sensor 1-2 Correlation

I also found this... though its for Trailblazers... but may give you a clue:
Reduced Engine Power Message and/or Check Engine Light with any Combination of the following DTCs: P0107 P0112 P0122 P0452 P1120 P1220 P1221 P1271 P1275 P1280 P1481 P1515 P1540 P1633 P1635 P1639 P1682 #PIP3192 - (Oct 18, 2004)

Reduced Engine Power Message and/or Check Engine Light with any Combination of the Following DTCs: P0107 P0112 P0122 P0452 P1120 P1220 P1221 P1271 P1275 P1280 P1481 P1515 P1540 P1633 P1635 P1639 P1682 PCM Repeat.

The following diagnosis might be helpful if the vehicle exhibits the symptom described in the PI.

Condition/Concern:
Reduced engine power message and/or check engine light with any combination of the following DTCs: P0107 P0112 P0122 P0452 P1120 P1220 P1221 P1271 P1275 P1280 P1481 P1515 P1540 P1633 P1635 P1639 P1682

Recommendation/Instructions:
If the SI diagnostics did not isolate a concern, the following information may be helpful:
- Inspect the main engine wiring harness between the PCM and the generator assembly for a potential short to ground. There is a metal wiring harness retainer in this area that secures the main engine harness. If the harness conduit is mispositioned, some of the wiring may become exposed and chaff on the harness retainer. This may eventually cause the exposed circuit to short to ground.

- Inspect the 3 harnesses that connect to the PCM for potential shorts to ground on the metal PCM mounting bracket, just below the PCM. There are plastic harness retainers on the PCM bracket that secure the harnesses to the PCM bracket. If the harness conduit is mispositioned, some of the wiring may become exposed and chaff on the PCM bracket. This may eventually cause the exposed circuit to short to ground.

- If a chaffed circuit is found in either of the above locations, repair the circuit using the necessary SI procedures. Once the circuit is repaired, tape the area of the affected area of the harness to prevent the wires from becoming exposed in the future and secure the harness using the original harness retainer.

This applies to 04:
- 4.2L 5.3L LL8 LM4 Engine with DTC - P2120 or P2122 or P2123 or P2125 or P2127 or P2128 - kw low MIL pedal power reduced #PI01746 - (Feb 17, 2004)
- 4.2L 5.3L LL8 LM4 Engine with DTC - P2120 or P2122 or P2123 or P2125 or P2127 or P2128.

When servicing the vehicle with the VIN you entered, the following diagnosis might be helpful if the vehicle exhibits the described symptoms.

Condition/Concern:
MIL light on. Reduced Power message on DIC. Possibles DTCs P2120 and/or P2122, P2123, P2127, and P2128.

Recommendation/Instructions:
The APP harness is clipped to the accelerator pedal bracket. The harness may chaff on the upper portion of the accelerator pedal causing a short to ground. Verify the harness is not chaffing on the accelerator pedal. After repairing the short, reposition the harness to ensure no contact between the harness and the accelerator pedal.

Hope helpes.

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1983 subaru gl. Starts up and will idle, but engine dies as soon as its revved up to about 2800-2900 rpm.


get the error codes read it sounds like you engine is in limp home mode as the management system has detected a fault

Oct 13, 2014 | Cars & Trucks

1 Answer

P2113 throttle pedal position sensor


remove the four screws holding the cover on the electronic portion and as you prise open the casing,very gently and only slightly you will be greeted with a cup of engine oil,you need a new throttle body

Nov 20, 2013 | Kia Sportage Cars & Trucks

1 Answer

Hyundai tucson crdi fitted a new throttle pedal but p2113 fault code keeps comming back


I hope you mean a throttle position sensor, if so it needs to be adjusted. also newer year models codes bust be removed with a scanner.

Nov 16, 2013 | Hyundai Cars & Trucks

1 Answer

Not shifting past 2900 rpm


when the garage replaced the throttle body ,what did they replace .there is 2 sensors on the throttle body. 1 is the idle air control valve and the other is your throttle position senor. it sounds to me your have a transmission problem. are there any codes

Dec 09, 2012 | Cars & Trucks

1 Answer

Engine starts and idles fine, but will not rev up (2001 Jeep Grand Cherokee 3.1 diesel auto)


If it was a fuel shortage the engine would rev but to limited speed. This is a lack of air to throttle body. Check for clogged air filter and all the piping and the throttle body.

Sep 28, 2012 | 2001 Jeep Grand Cherokee

2 Answers

I have a 2002 Mitsubishi Galant and in lower RPM it wants to chug and hesitate a little but in high RPM it drives fine. The ****** shifts smooth so I don't think its that but Im not sure what else


Hello
The engine and transmission in this cars drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL THE DIAGNOSIS & TESTING IS COMPLETED.

Jul 10, 2012 | 2002 Mitsubishi Galant

2 Answers

P1193 error code car wants to stall when stopping and accelerating


P1193 = Detected engine speed below 470 RPM. There are several possible causes/components which can contribute to this drivability issue. ELECTRONIC THROTTLE SYSTEM (ETS). In most cases, an ETS related DTC will set in pairs of codes. The first code denotes the related system or component. The second code is for the specific fault detected.
There was also probably P1191 - limp home

For this issue, on frequent occations I've found the throttle position sensor (TPS) (potentiometer) had bad spots in it and subsequently sending erratice signals to the ETS Control Module (additionally, the throttle body and plate had carbon buildup inteferring with the intake air flow. Also check for air leaks (intake air hoses, vacuum lines & tubes for cracks/leaking). Clean the throttle body & plate. Bench test the TPS. You also have an APS (Accelerator Position Sensor) located on the RH side engine compartment near the firwall next to the strut tower. These are the initial components to check/examine. Replace as needed.


ghost45_37.jpg

ghost45_38.jpg

Aug 31, 2011 | 2001 Hyundai XG300

1 Answer

Code 1294 the engine management light come on had diagnosis and found code. also is using more than usual fuel and is slow. before the management light came on the revs were sticking on to 2 000 revs...


It means that when you are in drive gear but idle, that the idle rpm is several hundred rpm different from the nominal 'target' rpm. I would begin by removing the air intake hose to the throttle body and using a solvent clean the throat of the throttle body, both sides of the throttle plate (move the acceleator linkage for access to the throat and rear side of the plate) and also the port of the air passageway at the side of the throat which is for idle air input. Check that the throttle linkage moves freely. Also look for any vacuum hoses connected to the intake manifold to be sure none are disconnected, and also make sure the ball in pcv valve in one of those hoses is moving freely.
See how the idle rpm then 'rides'. If that isn't sufficient, then the idle control circuits need to be considered, but those have a separate fault code.

Feb 12, 2010 | 2002 Jeep Grand Cherokee

4 Answers

High idle speed- Nissan N16 Pulsar/ Almera


Battery not charging well when airconditioner on ( also engine speed not increase when air conditioner on )

May 30, 2009 | Nissan Pulsar Cars & Trucks

1 Answer

No responce from accelartor after brake peddle is pressed


If check engine light is on get the codes pulled.

Jun 04, 2017 | 1996 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...