Question about Chevrolet Silverado 1500

Open Question

How to replace fuel pump 2000 chevy silverado

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
sledge1863
  • 149 Answers

SOURCE: 2000 Chevy Silverado 1500 Replace the fuel pump - ?

First check the fuel pump fuse in the fuse panel to make sure its not blown. Chances are that it is the fuel pump, that is a common problem with chevy trucks. The easiest way to access the fuel pump is to remove the bed of the truck from the frame. Good luck. dont forget to rate.

Posted on Mar 13, 2009

Ad
  • 27 Answers

SOURCE: process to change fuel pump on 2001 chevy silverado 1500

take the six bed bolt loose and then take three buddies slide the bed back put in the new pump slide it back n place and put the bed bolts back in. if u drop the tank u can easily break the hard plastis lines that go to the fuel tank. u only have to take the fill lines and taillight wires loose this way its alot quicker, and easier.

Posted on Aug 07, 2009

roniecon
  • 6927 Answers

SOURCE: Knock engine sensor light on truck is hesitating/

Did they replace the knock sensor?Check the wire going to the sensor(knock).Look for a bare place hiting up against something ,grounding it out.Make sure the plug to knock sensor is good.And make sure it is making a good connection,Knock sensors also ground a part of the computer to feed back imformation.This connection is a must,the truck will not perform at all,stumble,miss,and carry on.Sometimes even backfire.If they did not replace the knock sensor,replace it with high quality sensor from NAPA,or oem from dealer.This sensor has to be made perfect,no room for inperfection.The knock sensor is easy to replace,they just screw in a hole in the block.When removing the sensors,nothing will come out such as oil or water,this is a dry threaded hole.It is a bell shaped sensor.If you don`t know which sensor is bad,purchase one.replace one,and if there is no change,replace the other side with the old sensor you just took out,it will be a good one.I hope this helps you,Let us know if it does.

Posted on Oct 05, 2009

  • 14036 Answers

SOURCE: I just replaced the fuel

CHECK THE IGNITION FUSE.IF FUSE IS GOOD PROBLEM IS IN THE DISTRIBUTOR OR COIL BAD.

Posted on Apr 12, 2010

ZJLimited
  • 17970 Answers

SOURCE: replace a fuel pump on 2000 chevy cavalier

REMOVAL & INSTALLATION
(see Figures 1 and 2)

CAUTION The fuel injection system remains under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.

  1. Relieve the fuel system pressure using the recommended procedure.
  2. Disconnect the negative battery cable.
  3. Drain the fuel tank, then remove the fuel tank from the vehicle.
  4. While holding the modular fuel sender assembly down, remove the snap-ring from the designated slots located on the retainer.

WARNING The modular fuel sender assembly may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
  1. Remove the external fuel strainer.
  2. Detach the Connector Position Assurance (CPA) piece from the electrical connector and detach the fuel pump electrical connector.
  3. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tabs in the same manner.
  4. Lift the cover assembly out far enough to detach the fuel pump electrical connection.
  5. Rotate the fuel pump baffle counterclockwise and remove the baffle and pump assembly from the retainer.
  6. Slide the fuel pump outlet out of slot, then remove the fuel pump outlet seal.

To install:
  1. Install the fuel pump outlet seal, then slide the fuel pump outlet in the slots of reservoir cover.
  2. Install the fuel pump and baffle assembly onto the reservoir retainer and rotate clockwise until seated.
  3. Install the lower retainer assembly partially into the reservoir. Line up all 3 sleeve tabs. Press the retainer onto the reservoir making sure all 3 tabs are firmly seated.

Gently pull on the fuel pump reservoir from retainer to assure a secure fastening. If not secure, replace the entire fuel sender.
  1. Attach the fuel pump connector.
  2. Fasten the CPA connector to the fuel sender cover.
  3. Install a new external fuel strainer.
  4. Install the modular fuel sender.
  5. Install the fuel tank in the vehicle.
  6. Connect the negative battery cable.
  7. Pressurize the fuel system and verify no leaks.
35a484a.jpg

Fig. 1: The module fuel sender assembly is mounted in the fuel tank

fbd4d43.jpg

Fig. 2: Modular fuel pump component identification




Hope this help to solve your problem (remember comment and rated this).

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just replaced fuel pump in 2000 chevy 2500 and when put in gear feels like it might die but fine once it gets going?


Check for proper ground to fuel pump. did you replace the fuel filter? idle air control valve may be sticking or you have a vacuum leak.

Sep 07, 2010 | 2000 Chevrolet Silverado 2500

1 Answer

2000 suburban water pump replacement


this site should help out, but if not i can look for more info, the engine is the same thing even though the truck is different
http://www.ehow.com/how_4506106_replace-fuel-pump-chevy-silverado.html

May 19, 2010 | 2000 Chevrolet Suburban

1 Answer

2000 chevy 6.0 starting problems


Let me tell you the truth, its your fuel pump. everybody tells you to check youre injectors and replace youre fuel filter but the truth is its your pump. all chevy and gmc models have that problem. I just replaced mine. i have a 2001 chevy 2500hd also with the 6.0 and did the exact same thing. I bought a fuel pump and put it in and BINGO truck runs and starts like new. TRUST ME MAN

Aug 11, 2009 | 2005 Chevrolet Silverado 1500HD

1 Answer

Fuel Sending unit on a 2000 Chevy Silverado


if it is the fuel level sending unit you will have to replace the pump because they are a 1 piece assambly. it will be a task to change too as you will need to either remove the truck bed or drop the fuel tank to get to it.

Mar 14, 2009 | 2000 Chevrolet Silverado 2500

2 Answers

2000 Chevy Silverado 1500 Replace the fuel pump - ?


First check the fuel pump fuse in the fuse panel to make sure its not blown. Chances are that it is the fuel pump, that is a common problem with chevy trucks. The easiest way to access the fuel pump is to remove the bed of the truck from the frame. Good luck. dont forget to rate.

Mar 13, 2009 | 2000 Chevrolet Silverado

1 Answer

FUEL PUMP FOR CHEVY SILVERADO


fuel filter? how about power to the fuel pump,loose ground wire to chasis? wiring harness? terminals clean at point of connection?did you check the fuel pump relay? Relay is located in electrical center under the hood on the driver side.relay and fuse legend will be on bottom side of cover, you sould be able to switch with another relay that you know works, ie: switch horn relay with fuel pump relay, honk horn to insure both relays are working when either relay is inserted into horn slot. Do you by chance have the electrical schematic drawing for the fuel pump?

Feb 17, 2009 | 2000 Chevrolet Silverado

1 Answer

Turn over but well not stay running backfires though air intake


When is the last time you replaced your fuel filter? Check your fuel filter. If it's plugged you may have taken out the fuel pump. This happened to me. (2000 Chevy Silverado 1500)

DC

Jul 29, 2008 | 2000 Chevrolet Silverado

5 Answers

2000 chevy silverado 1500 4.3 eng


Chevy Trucks, Blazers, S10 pickup and the like will vapor lock ecspecially the 2000 models. Do not tighten the gas cap past 1 click. There is a tube that runs from the top of the tank down and this gets hot and collapses or burns in half. We just bought a reinforced rubber tube cut it to lengh and use it instead of part and it's worked grat for 2 years so far.

Jul 21, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...