Question about Cars & Trucks

1 Answer

I have a 1995 Ford Crown Victoria 4.6 liter, I

I have a 1995 Ford Crown Victoria 4.6 liter, I recently bought a transmission from the local pull and pay and had it install at a licensed mechanic. and when I went to pick a car up from the shop the engine start to spuder and had no power and before I took it to the mechanic I never had a problem with the engine.. so my question is how to fix a engine that sounds like it needs a really bad tune up even though I change the spark plugs and wires. if you don't press the gas engine runs fine and as soon as you give it gas is start to run rough with less power.. someone please help me with this problem Thanks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Well its really difficult to understand your car problem like what you breff it anyhow you can mail me & explain what excitly your car doing & what kind of noice you are getting it & if your car showing check light on dash,if yes then go for scanning your car & find out whats your car having problem , or pls feel free to write on my mail ....

Posted on Nov 21, 2013


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 580 Answers

SOURCE: 4.3 liter engine, got bad gas, fuel pump went out,

Are you sure it's bad gas causing the problem? It could be a faulty idle sensor or more than likely the coolant sensor near the thermostat housing malfunctioning. It could be sending the wrong signal to the pcm(power control module) causing the timing to be too far advanced thus causing the low speed chugging & hard starting. Good luck!

Posted on Apr 17, 2010

  • 171 Answers

SOURCE: 2002 Galant, Stalling at lights

Check the Crankshaft Position Sensor. This causes this exact effect.

Posted on Sep 29, 2008

  • 1619 Answers

SOURCE: 1990 chevy corsica 3.1 liter v6 engine. started

Coils and wires are the most likely culprits as they never get replaced hardly ever. You cant really test a coil, you can check for resistance on the plug wires but that doesnt tell you if the insulation is bad on them.

Posted on May 18, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to get windows to go up and down in 1995 ford crown victoria

No up
No down
One window
All windows
Window fails down
You hear motor run & no window movement
You work the switches & they work sometimes

I would imagine you need that answered at a
repair shop

Feb 14, 2013 | 1995 Ford Crown Victoria

1 Answer

I wanted to know where is the transmission located on a 1995 Ford Crown Victoria

If you you open your drivers door look in underneith the vehicle at the front of the door it is in the middle of the car

Sep 20, 2011 | 1995 Ford Crown Victoria

2 Answers

My engine oil dipstick is missing on my 1999 ford crown victoria 5.6 liter engine what is the length of it so i can get a universal one


Feb 14, 2011 | 1988 Ford Crown Victoria

1 Answer

How much should I pay for the y pipe on the exhaust system. Its a 5.0 motor 1987 crown victoria 4 door.

Wouldn't you look on a web site such as NAPA
or call a local auto parts store?

This is not a data base or a business site

Jan 31, 2011 | 1987 Ford Crown Victoria

1 Answer

I just bought 1995 ford crown vic interceptor, it needs repair i believe, it sounds like crickets at times and makes radiator noises when i park after driving

sounds like its overheating --ask a local mechanic to have a look ,hope you didnt pay a lot for a 15yr old vehicle no more than scrap value and definatly not more than a 700euros

Aug 22, 2010 | 1995 Ford Crown Victoria

2 Answers

What is the cylinder order on an '89 5.0? Also, what is the spark plug order?

1989 Ford Crown Victoria 5.0 liter V-8 VIN "F"


Remember rated and comment this; good luck.

Aug 19, 2010 | 1989 Ford Crown Victoria

1 Answer

Where is the location of no. of cylinder on crown

2004 Ford Crown Victoria 4.6 liter V-8 VIN "W"


Hope helps (remember rated this).

Jul 19, 2010 | 1997 Ford Crown Victoria

1 Answer

How to replace rear turn signal on 1995 crown victoria

open the trunk and remove the trim panel closest to you whare the latch is. now pull the carpet down on the side you need to fix, remove the 4 nuts holding the lamp assembley, pull the lamp assembley straight out from rear of vehicle .

Jan 22, 2009 | 1995 Ford Crown Victoria

1 Answer

Itman arm removal - 1995 ford crown vic

remove the nut then buy a pitman arm puller at your local autoparts store, this tool will pull the pitman arm from the steering box.

Oct 05, 2008 | 1995 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14512 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides