Question about 1994 Ford Ranger Supercab

Open Question

1994 ford ranger check engine light - 1994 Ford Ranger Supercab

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chazman05
  • 48 Answers

SOURCE: 1995 Ford Ranger ( engine light ) and stuff need help plz

if your obd2 scanner fits the connection you have obd2, obd1 connector is way differnt.

your code p1443
Control System
Canister Purge
Valve (Mechanical)
Malfunction
Monitors the fuel vapor
flow between the
engine intake manifold
and the EVAP
canister. The system
failure occurs when a
leak or blockage
between the intake
manifold, the EVAP
canister purge valve
and the EVAP canister
is detected by the
PCM.
l Pinched, blocked or
plugged fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister
l Disconnected, cracked
or cut fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister purge valve
Check for audible vacuum
noise in the engine
compartment or significant
fuel odor in the engine
compartment or near the
EVAP canister.

This link has all the codes you need.
http://rockledge.home.comcast.net/~rockledge/RangerPictureGallery/DTCs.pdf

Posted on Dec 16, 2008

Ad

SOURCE: Check engine light is on. EVAP small leak

You need to check the purge and vent solenoids for proper operation. You need to check the pressure sensor for out of range ( defective ). You need to check the filler neck for cracks and make sure the clamps are tight. You need to check the vapor lines for loose fit. I've seen at the charcoal cannister where the lines connect it may not be on strait. A smok test will reveal this if its not sealing. You may have a leaking rollover valve or fuel pump seal on top of the tank. You may just have a vacuum leak under the hood, These trucks have an Evap management valve also that can be leaking or out of specs. Look on the emmisions lable or vacuum chart under the hood. This will show you the underhood components.

Posted on Jul 15, 2009

  • 14036 Answers

SOURCE: how do i turn off the check engine light on my

YOU CANT TURN OFF PCM WHEN IT SPOT A PROBLEM.YOU HAVE TO FIX PROBLEM.BECAUSE THE CHECK ENGINE WILL STAY ON UNTIL PROBLEM FIX. ITS AGAINST THE LAW TO TAMPER WITH EMISSIONS SYSTEM.BECAUSE OF SMOG AND POLLUTION LAWS..HAVE TRUCK SCAN TO SEE WHAT YOUR PCM CODE IS.COULD BE SOMETHING MINOR.

Posted on Sep 30, 2009

  • 33 Answers

SOURCE: removal and install timing belt 1994 ford ranger/

Depends on the engine.

Posted on Oct 10, 2009

  • 1 Answer

SOURCE: My 1994 ford ranger ... the starter cranks.. but

Had the same problem and it's so simple a fix. It's the Fuel Relay Fuse located in the fusebox in the engine compartment on the driver side. Take It costs like $13 and is the same as the AC relay. Next time it happens pop the AC fuse in it's place.

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble shoot turn signals 1994 Ford Ranger 2.3 engine


Diane, There are 2 separate flashers on your vehicle, one is for the emergency/4 way lights and one flasher is for the signal lights. It may be worth the couple bucks and replacing the signal flasher as a first step. Recheck bulbs/sockets, fuses/relays, flasher. If all looks good possible signal switch is bad. Remove switch and try to clean contacts or replace switch. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://ca.answers.yahoo.com/question/index?qid=20090405174036AARb2Uc
1994 Ford Ranger Turn Signal Electrical Problem 1994 Ford Ranger
93 Ranger Turn Signal Problem Ford Truck Enthusiasts Forums

Aug 20, 2016 | 1994 Ford Ranger Supercab

1 Answer

Where is the egr valve located on a 1994 ford ranger


should be on the back driver side of the motor

Apr 21, 2014 | 1994 Ford Ranger Supercab

1 Answer

My 1994 ford ranger ... the starter cranks.. but if the check engine light does not come on... it doesnt start... when the light comes on.. it starts... Intermittent... what do I check ??


Had the same problem and it's so simple a fix. It's the Fuel Relay Fuse located in the fusebox in the engine compartment on the driver side. Take It costs like $13 and is the same as the AC relay. Next time it happens pop the AC fuse in it's place.

Aug 05, 2010 | 1994 Ford Ranger Supercab

1 Answer

1994 ranger 2.3 lacks power and has a miss. put new plugs and wires. plus a new mass air flow sensor. no check engine light on


I would check for a vacuum leak, also check the air filter and replace the fuel filter, if it hasn't been done.

Jun 06, 2010 | 1994 Ford Ranger Supercab

1 Answer

I have a 1994 ford ranger, 4.0L. Cruise control


replace your brake light switch and it will all work

Sep 30, 2009 | 1994 Ford Ranger Supercab

1 Answer

How do i turn off the check engine light on my 1994 ford ranger, in order to pass smog?


YOU CANT TURN OFF PCM WHEN IT SPOT A PROBLEM.YOU HAVE TO FIX PROBLEM.BECAUSE THE CHECK ENGINE WILL STAY ON UNTIL PROBLEM FIX. ITS AGAINST THE LAW TO TAMPER WITH EMISSIONS SYSTEM.BECAUSE OF SMOG AND POLLUTION LAWS..HAVE TRUCK SCAN TO SEE WHAT YOUR PCM CODE IS.COULD BE SOMETHING MINOR.

Sep 30, 2009 | 1994 Ford Ranger Supercab

2 Answers

Code 224 on 1994 ford ranger. Checked primary


how did you check coils you can ohm them and they all should read the same... another way if you do not have an expensive scanner you can scope the current draw of each coil....or simply go to junk yard ...rob a set of coils and change all... do yourself a favor change plugs to standard autolite plugs.. let me know

Aug 31, 2009 | 1994 Ford Ranger Supercab

1 Answer

Using to much gas black exhaust 1994 ford ranger


check to see what codes are present. sounds like it is running rich check o2 sensors vacuum leaks map sensor. 

Mar 04, 2009 | 1994 Ford Ranger Supercab

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...