Question about 1997 Jeep Wrangler

Open Question

Jeep instrument cluster not working - 1997 Jeep Wrangler

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: 1998 jeep wrangler dashboard

chrysler tsb 08-015-99 pertains to this problem. there is a wiring connector on the cluster that needs replaced.part number is 5016261aa for the connector and 4778570 for te heat shrink

Posted on Oct 02, 2008

  • 750 Answers

SOURCE: Instrument cluster on 1997 Jeep Wrangler...gauges

faulty cluster may have to replace it. try testing a junked unit if it works keep it.

Posted on Jul 16, 2009

  • 6 Answers

SOURCE: instrument cluster lights don't work. Fuses and bulbs are good.

feed wire for the lights may have failed or the circuit on the board may have gone. if you remove the cluster you can put a supply to the bulb circuit (carefully) and check if it is the circuit. If it's ok you can run a new feed to the cluster from your lights. Job done.

Posted on Feb 16, 2010

Testimonial: "thank you,you were very helpfull. i believe you got it.."

  • 1 Answer

SOURCE: Have 97 Jeep Wrangler with instrument cluster

I am having the same issue with my 98. Did you figure it out?

Posted on Apr 25, 2010

  • 3 Answers

SOURCE: Instrument cluster (gauges) go off and on

main computer board going bad

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instrument cluster repair


no car car stated , just a jeep
a 2000 wrangler,what.?
and which engine./? Size.?
then state what lamps work and which dont?

but do check all fuses fires. in both boxes.
always.

the clusters have
Parking lamps
idiot lamps (key, seat, charge, oil, CEL)
and some have LCD or other very fancy displays. like my 08
i cant guess, you must say car and whats wrong.

Jan 03, 2014 | Jeep Cars & Trucks

1 Answer

What relay controls the instrument cluster?


I just took off my stereio from my jeep and ten disk cd changer and had a connector loose for pulling on it. Check under the dash below the steering column.Their are connectors check if any are loose. I do my own work so i can save.

May 21, 2012 | 1996 Jeep Grand Cherokee

1 Answer

Instrument cluster works intermediately. put another cluster in and changed starter switch and put on new cable ends on battery and still doesn't always work. What's the problem?


just a thought but does your dash have a dimmer switch?as you've changed the cluster and its still not right it could be that.

Jan 29, 2012 | 1998 Jeep Wrangler

1 Answer

INSTRUMENT CLUSTER NOT WORKING CODE ON ODEMETER IS noFLSH


When the instrument cluster displays "no FLSH" it means there is no operating software in the instrument cluster...This is a Jeep term for No Flash. Your instrument cluster may be able to be reprogrammed with software, but that can only be done by a Jeep dealer. Your only other option would be to replace the instrument cluster...I hope this helps.

Aug 08, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Instrument cluster lights don't work. Fuses and bulbs are good.


feed wire for the lights may have failed or the circuit on the board may have gone. if you remove the cluster you can put a supply to the bulb circuit (carefully) and check if it is the circuit. If it's ok you can run a new feed to the cluster from your lights. Job done.

Feb 16, 2010 | 1995 Jeep Cherokee

1 Answer

1998 airbag light comes on and off. when light is on the spedometer and rpm dials go to zero when airbag light goes off they work again. This is not a continous problem but does it off and on.


There is a loose connection (or corrosion) where the instrument cluster attaches to the wiring harness mount. Remove the screws (2) from the dash cover below the steering wheel and remove the panel. Remove the defrost vent cover (just lift carefully, it only snaps into place. Remove the screws around the cluster panel cover and remove the cover. Remove the the instrument cluster (it pulls straight out toward you) and make sure the wires are not corroded. Make sure the wiring harness is firmly attached to the metal bracket that holds them in place. Carefully push the instrument cluster back into place. While firmly holding the cluster in place, install and tightnen the screws that hold the cluster. After tightening, wiggle it and make sure it's solid. Start your Jeep and make sure everything works. Shut jeep off and install the rest of the panels in the reverse order of removal. This should fix your problem. What happens is, the cluster becomes loose, speedo quits working (sometimes all other gauges quit also) and gives an airbag code.

Nov 13, 2009 | 1998 Jeep Wrangler

3 Answers

Gages speedo tac all quit. fuses are good 98 jeep wrangler. did it before but came back on. changed gage cluster still will not work


Have you checked it with a scan tool to be sure it is actually getting the information? The instrument cluster do go out, meaning the ribbon on the back.I would check the connection, then turn to a way to determine if it is recieving a signal from ECM.

Oct 09, 2009 | 1998 Jeep Wrangler

1 Answer

Gas gauge no longer works


The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures.
Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install
Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors
NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel.
Remove the instrument cluster from the vehicle.
Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.)
when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks

May 14, 2008 | 2007 Jeep Scout

Not finding what you are looking for?
1997 Jeep Wrangler Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...