Question about 1998 Nissan Maxima

Open Question

1998 nissan maxima ignition problems - 1998 Nissan Maxima

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Starter motor and ignition switch and O2 sensor and pipe 1997 Nissan Maxima

You need to remove all of the air intake and other things behind the battery. The start motor is held in with two bolts. You might need a breaker bar to break loose the one bold as I did. Once you remove all of the air intake equipment. This will help you gain access to the starter motor. You might not need to remove all the air intake equipment I know it made it alot easier for me to remove the starter and I took it to the auto store and had it tested.

Posted on Apr 07, 2009

  • 202 Answers

SOURCE: brake lights stay on and ignition is off

your brake light switch has malfunctioned. it is locatad on top of the brake pedal but you have to stand on your head to see it up there it is a very easy fix one nut and one wire clip. when you replace it have some one watch the back of the car while you push the brakes. you will have to adjust the switch so that when you tap the brake pedal a little ways the brake lights come on. and if you do not feel comfertable to do this you can take it to a repair shop of your choice. i hope this helps you. and please rate my solution
thank you

Posted on Apr 21, 2009

  • 736 Answers

SOURCE: CHANGED SPARK PLUGS NOW HESITATING & RUNS

chances are an ignition wire was damaged when you tugged on it to remove it from the old plug .. the ignition cables have a high resistance wire inside (not a solid wire) this is not hard to damage .. check to make sure each wire is properly seated on the plug .. its easy to not get it on all the way since you cant see it ..

Posted on Sep 14, 2009

  • 1949 Answers

SOURCE: I have a 1998 nissan maxima that starts but when

electirc part of the ignition needs replaced

Posted on Mar 04, 2011

dttech
  • 4803 Answers

SOURCE: 1998 nissan maxima 3000 v6 drive belt diagram

You forgot to mention "with A/C" or "without A/C". Here are both drive belt routing diagrams.

1_24_2012_11_57_19_pm.gif

1_24_2012_11_57_46_pm.gif

Posted on Jan 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Nissan Maxima, key broken off in ignition, any ideas?


Use a small or mini pair of needle nose pliers to grab it and pull it out but make sure it is in the off position

Jun 21, 2014 | 1998 Nissan Maxima

1 Answer

When i go to start my 1998 nissan maxima nothing happens


IT MAYBE THE IGNITION SWITCH OR AWIRING PROBLEM. IT'S A PROCESS OF ELIMINATON, RUN IT DOWN. A READER MIGHT HELP YOU WITH THIS.

Feb 01, 2013 | 1998 Nissan Maxima

1 Answer

I have a 1998 Nissan Maxima GLE, engine was replaced with a 1998 SE engine. Since then, I have been having problems starting. I get a boost and once I move the car and park it, it won't start again....


there is a problem with your iginition timing. it is most probably overly advanced. have an experienced mechanic check your ignition timing. the mechanic should check the distributor, camshaft, and crankshaft timings.

Aug 12, 2011 | 1997 Nissan Maxima

1 Answer

98 MAXIMA P1320 WHAT IS THE CAUSE ING SIGNAL PRIMARY CIRCUIT FAULT


Nissan had a lot of problems with ignition coils and the wiring harness that goes to them. You must inspect the wiring very very carefully and if that does not reveal anything, you can get new updated coils, either from nissan or an independent auto parts store. They are expensive and different front and back.

ce01ac8.jpg

Feb 23, 2010 | 1998 Nissan Maxima

1 Answer

CHANGED SPARK PLUGS NOW HESITATING & RUNS


chances are an ignition wire was damaged when you tugged on it to remove it from the old plug .. the ignition cables have a high resistance wire inside (not a solid wire) this is not hard to damage .. check to make sure each wire is properly seated on the plug .. its easy to not get it on all the way since you cant see it ..

Sep 14, 2009 | 1998 Nissan Maxima

1 Answer

1) Apx. how much would it cost parts & labor to change Ignition switch on a 1998 Nissan Maxima SE? 2) Do you think I can find the parts?


HI, the cost of the ignition switch is $27.99. the labor cost is usually figure by the hour and it is set a 50 dollar an hour increment. In my shop, we have a set minimum labor charge of two hour as most shops in my area. Total estimated cost including the labor and parts should be around $127.99 give or take.

You can most certainly purchase this part yourself on-line at www.autozone.com

Part Number is - LS812
OEM Number---- 48750- 1E411

Please rate and god bless:)

May 07, 2009 | 1997 Nissan Maxima

1 Answer

1998 Maxima misfire code cylinder #1


your not getting any fuel into the cylinder

Mar 22, 2009 | 1998 Nissan Maxima

1 Answer

No start


sounds like a bad battery...

Mar 22, 2009 | 1998 Nissan Maxima

Not finding what you are looking for?
1998 Nissan Maxima Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...