Question about Jeep Liberty

Open Question

How to replace jeep liberty starter - Liberty Jeep Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2002 jeep

My wife had a similar problem with a 2003 Jeep Liberty. Her problem was that it stalled and she could not get it restarted unless it sat off for 30-45 minutes. It seemed like it was a problem with the alternator and battery but it had just gotten a brand new battery in it and we discovered the starter would roll over after the Jeep sat. We had it towed to the dealership and they replaced the Crank Sensor and the Timing Sensor and the Jeep now runs fine again. Side note: They charged us about $200 to fix these parts.

Posted on Sep 13, 2008

  • 454 Answers

SOURCE: replaced starter 2006 jeep liberty still won't

Check that you have power at the main post of the starter. Then check the solenoid activation circuit from the ignition switch.

Posted on Oct 04, 2009

Testimonial: "have power at post on starter-could it be safety neutral switch on transmission?"

ZJLimited
  • 17970 Answers

SOURCE: 2004 jeep liberty replacing the starter

2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Posted on Oct 05, 2009

  • 151 Answers

SOURCE: My 2009 jeep liberty takes several tries to get it

try getting a full tune up done spark plugs and wires ect....

Posted on Jul 14, 2010

  • 1 Answer

SOURCE: I have a 2002 jeep

does it turn over or even click when u turn key? I have one as well. Wouldn't start at gas station. There is a pot medal piece that the actual ignition pushes into that was broken. Part is not available from dealer. you'll need to get used or new column.

Posted on Sep 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Jeep Liberty has an intermittent starting problem. At times the car will not start, the starter will not even engage. If left for a couple of hours it will then start.


You could have a fuel delivery problem. Start by
  • checking fuel pressure. Fuel injected cars are very fuel pressure sensitive. Fuel pressure is very important and must be within specifications. However, if the pressure is low, it does not mean the pump is bad.
  • A plugged fuel filter, a pinched line, and low voltage at the pump can contribute to low fuel pressure. All three must be checked before replacing the pump.
  • Rrefer this link http://www.carpartswarehouse.com/carmode... to learn about other parts of Jeep Liberty. Also you can get Jeep Liberty parts at good price.

Dec 14, 2014 | 2002 Jeep Liberty

2 Answers

Why wont my 2003 jeep liberty start?


I had that problem with my 2002 Jeep Liberty and the ignition switch cracked so I had that replaced. I am not sure if that is included in the ignition lock cylinder ...

Jun 25, 2014 | 2003 Jeep Liberty

1 Answer

2002 jeep liberty has an intermittent starting problem. The starter makes a grinding noise usually when started and has for a while. could these two be related?


the starter grinds because the bushings at each end are worn .or if the engine has been removed and replaced,, the person didnt replace the spacers from the starter and bell housing which keeps the starter gears from going too deep into the fly wheel makeing a grinding sound. the intermittent starting problem could just be the check valve on your fuel system bleeding back . need more info.

Nov 07, 2013 | 2002 Jeep Liberty

1 Answer

2007 jeep liberty replacing the starter


The exhaust has to be lowered in order to remove your starter.If you have shims remember to install them back.

Jan 21, 2013 | 2007 Jeep Liberty Sport

2 Answers

My 2005 jeep liberty will not start. Starter is good. What could be the probable cause?


Check the battery for bad connections..take off the cables and clean both the battery posts and the cable connectors and then try...if no start, then see if you can check the battery voltage with a voltmeter...at stand still(engine not running) the battery should read 12.5 volts...if battery is ok, then there is the possibility that the starter solenoid, the starter relay, or (in rare cases) the ignition switch is bad

May 26, 2011 | 2005 Jeep Liberty

1 Answer

Jeep liberty starter sticking in cold weather


Generally I have seen this happen when water gets into the starter and freezes overnight. When you first try to start it, the starter won't work correctly but heat generated while it's stuck will quickly melt the ice and then it works. Only way I know of to eliminate it is to remove the starter and use grease on all the moving parts that connect the solenoid to the starter Bendix drive. Not sure why, but it seems to happen on some starters but not all, even on identical vehicles. I have corrected the problem on many customers cars by greasing but have left mine alone and actually never had a problem other than the initial "being stuck" in the AM. If your starter is very old, you could replace it but that is up to you.

Jan 08, 2010 | 2003 Jeep Liberty

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

Replaced starter 2006 jeep liberty still won't turn over 3.7 engine


Check that you have power at the main post of the starter. Then check the solenoid activation circuit from the ignition switch.

Oct 04, 2009 | 2006 Jeep Liberty

1 Answer

2002 jeep


My wife had a similar problem with a 2003 Jeep Liberty. Her problem was that it stalled and she could not get it restarted unless it sat off for 30-45 minutes. It seemed like it was a problem with the alternator and battery but it had just gotten a brand new battery in it and we discovered the starter would roll over after the Jeep sat. We had it towed to the dealership and they replaced the Crank Sensor and the Timing Sensor and the Jeep now runs fine again. Side note: They charged us about $200 to fix these parts.

Aug 28, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...