Question about 1999 GMC Sierra

1 Answer

I accidentaly drained all of my transmission fluid

How much transmission fluid do i add

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

3/to five litres or till it seeps out of transmit ion plug where filling

Posted on Nov 21, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I drained all my transmission fluid accidentaly


do you know where about it came from the drain plug? it will take around 4-4.5L of dexron/mercon oil

Nov 21, 2013 | 1999 GMC Sierra

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

How to check transmission fluid 2010 lexus rx350 fwd


to check transmission fluid in a 2011 lexus rx 350 fwd there is no dipstick, but the transmission is not sealed as the dealer will tell you, thats a gimic for you to bring youre car to a dealership!
simply remove the drain plug from the transmission on the main bottom, the fluid will not come out, there's another fluid retaining plug above that!
next the fluid add hole is on the side of the transmission behind the driver side wheel towards top of transmission!
you simply add fluid whether you pump it in or snake a rubber hose off of a funnel, when the fluid is full it will come by the bypass plug and leak out the drain hole, at this point that's the correct amount of fluid!
simply re install the drain plug and the fluid add plug and you're done!
cost me $100 at a transmission shop to find this out yesterday

May 04, 2012 | 2010 Lexus RX 350

2 Answers

How to Change transmission fluid on 2001 celica


Hi there, hope these few steps help:
  • Raise the car with a jack and support the vehicle with jack stands sufficiently rated to safely support the weight of the vehicle.
  • Place a large drip pan under the transmission.
  • Remove the transmission fluid drain bolt with a wrench. The drain bolt is located at the bottom of the transmission facing the pan. The pan is the large flat plate that covers the very bottom of the transmission.
  • Drain the transmission fluid into the drip pan.
  • Reinstall the transmission fluid drain bolt with the same wrench used to remove the bolt.
  • Lower the vehicle to the ground after removing the jack stands.
  • Open the hood and remove the transmission dipstick from the filler tube by pulling the dipstick. The end of the dipstick will be curved into a circle to allow a finger to slide into the circle to withdraw the dipstick.
  • Place a funnel into the dipstick tube and fill the transmission with new fluid by pouring the fluid into the dipstick tube.
  • Remove the funnel and check the fluid level with the dipstick until the fluid reaches the "Full" mark on the tip of the dipstick.
  • Start and allow the engine to run for a few minutes.
  • Move the transmission gear selector through all of the gears while depressing the brake pedal.
  • Turn the engine off and check the fluid level on the dipstick. Add transmission fluid if necessary.
Best of luck.

Jan 11, 2011 | 2001 Toyota Celica

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

1 Answer

I just want to know where you add the transmission fluid in a dodge durango? i can't find it


Drive the Durango for 15 to 20 minutes to warm up the transmission fluid. When the fluid is warm, it will drain better and remove more contaminants from the engine. Raise and support the front of the Durango on ramps or jack stands. Place a large drain pan beneath the transmission.

Loosen the transmission pan retaining bolts with a socket wrench. Remove the bolts, but leave one at each of the four corners of the transmission pan. Slowly loosen the remaining bolts a little at a time.Fluid should begin to drain from the seal on the transmission pan. If the pan is stuck, break the seal by gently prying it loose or tapping it with a rubber mallet.

Support the pan with one hand and remove the bolts on one side of the pan. Allow the transmission fluid to drain until it stops. Remove the two last bolts. Remove the pan and drain the rest of the fluid.

Remove the three screws that hold the filter onto the transmission. Note that these screws may be Torx style. Install a new transmission fluid filter.

Clean the transmission pan and the magnet with solvent. Remove the old gasket material from the transmission pan. You may need a scraper to remove it all. Clean the mating surfaces with a lint-free cloth soaked in solvent. Let the pan air dry.

Put the new gasket on the pan and align them. Remove the gasket, apply a few drops of adhesive on the pan and replace the gasket. Realign the gasket before the adhesive dries.

Replace the pan onto the transmission and replace the retaining bolts. Tighten the bolts in a crisscross fashion to 150-inch pounds with a torque wrench. Return the Durango to level ground.




Refill the transmission with new fluid a little at a time, while checking the level often. Continue to add transmission fluid until it passes the "Add" mark on the dipstick, but doesn't pass the "Full" mark.

Start the engine, shift the transmission through all the gears and place the gear selector back in "Park." Recheck the transmission fluid level and add more fluid if needed. Don't overfill the transmission.

Replace the dipstick into the filler tube. Turn off the engine.

Aug 15, 2010 | 1999 Dodge Durango

2 Answers

How do you add transmission fluid to a 2000 town country


The tranny fluid is added through the tranny dipstick (make sure it's not the oil dipstick). Fluid color should be red and the dipstick should have instructions on how to check level (car in park, engine at idle). Funnels are your friend here.

Jul 26, 2010 | 2000 Chrysler Town & Country

3 Answers

What is the full capacity for transmission fluid fora 5.7L 2005 chrysler 300


TRANSMISSION FILL
To avoid overfilling transmission after a fluid change or overhaul, perform the following procedure:
  1. Verify that the vehicle is parked on a level surface.
  2. Remove the dipstick tube cap.
  3. Add following initial quantity of Mopar ATF +4, Automatic Transmission Fluid, to the transmission:
    1. If only fluid and filter were changed, add 5.0 L (10.6 pts.) of transmission fluid to transmission.
    2. If the transmission was completely overhauled or the torque converter was replaced or drained, add 7.7 L (16.3 pts.) of transmission fluid to transmission.
  1. Check the transmission fluid and adjust as required

Dec 06, 2009 | 2005 Chrysler 300

1 Answer

How do you add transmission fluid on 2004 suzuki forenza. It noip stick.


Welcome to the new era in automatic transmissions - sealed systems with "lifetime" transmission fluid. This is progress???

What makes you believe it needs fluid?

There are ways to drain and add fluid on most of these "sealed" transmissions; however, it involves drain and fill plugs underneath the car. This is not a procedure for do-it-yourselfers.

Oct 10, 2009 | 2004 Suzuki Forenza

2 Answers

I need to fill the transmission fluid on my 1989 Ford Festiva.


use a very small funnel placed into the dipstick tube check frequently with the dipstick so you don't overfill

May 25, 2009 | 1989 Ford Festiva

Not finding what you are looking for?
1999 GMC Sierra Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...