Question about Cars & Trucks

Open Question

Valve settings d0836 man diesel - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hi Ace 2L diesel van. What is the valve clearance warm and cold?


Cold: Intake 0.30mm, Exhaust 0.50mm.
Hot: Intake 0.20mm, Exhaust 0.040mm.

The 2L Toyota engine runs an overhead cam with bucket lifters, and requires removing and replacing of shims to adjust clearances...

Feb 13, 2016 | Toyota Cars & Trucks

1 Answer

2006 GMC 4500 Diesel Truck - code P0039..At random intervals the engine will drop to idle and CEL illuminates. The throttle will not operate. what sensors I should replace and it what order? Thanks


Dodge Cummins Error Codes List - Diesel Bombers



www.dieselbombers.com > Dodge Cummins > Dodge Diesel Tech Articles

Apr 6, 2009 - It appears to have every CEL code known to man... or at least known to Dodge. ... Chevy/GMC Truck and Duramax Turbo Diesel Forum · Chevy/GMC Duramax... General · 2011 · 2013+ · 2007.5 - 2012 LMM · 2006 - 2007 LBZ .... P0039 Turbo/Super Charger Bypass Valve Control Circuit Range/Performance

Aug 23, 2015 | GMC Cars & Trucks

1 Answer

I have MAN TGS 33-360 with hard starting.It operate with no problems until it is switched off.Then have to pump lift pump in order for it to start.No fault codes


if you have to pump lift pump that indicates a loss of pressure in the system to the pump/in the pump
check for fuel leaks and faulty non return valve in the pump
take it to a service dealer or an accredited diesel shop

Jul 12, 2015 | Cars & Trucks

1 Answer

How do I set tappets of a 2.5 diesel turbo mazda


you haven't mentioned if it is a 4 cyl or not. However bring no 1 cylinder up to tdc and watch the tappets of the next cylinder to fire. when that cylinders rockers are in valve overlap situation ( exhaust starting to close and inlet starting to open) then that will be maximum clearance on no 1 cylinder and is when you set the tappets turning the engine until the next cylinder is at TDC watch for the next cylinder again to be in valve overlap and repeat as for no 1 cylinder

Dec 25, 2014 | Mazda Cars & Trucks

1 Answer

Grand vitara RF diesel oxygen sensor location


old post.
in what country.?
smog controls vary by , you guessed it, country.
2 used world wide, diesels.
2.0 L RF/RFM I4 (diesel)
2.0 L RHW/RHZ I4 (diesel)

RF.
did you look first?
at the exhaust header, for 4 pin devices, (sensor) there.
look again. its there.
are you even sure there is ONE?
or just chasing RUMORS?

ever consider buying the FSM for this car.
and now no more wild goose chases?
ask suzuki for the service man.

its really a MAZDA , i think
A direct-injection turbo version (101 bhp) with four valves per cylinder, called the DiTD was introduced in the June 1998 Mazda 626 Wagon 2.0 DiTD. Engine has SOHC valve train with rocker arms and mechanically adjusted screws (no hydraulic valve lifters), with Denso V5 rotary injection pump and Denso PCM.

if it is, then the 02 is at the header collector junction, very near.
the down pipe. or the actual exh. manifold end collector.
like most cars....

Jun 24, 2014 | 1999 Suzuki Grand Vitara

1 Answer

Valve setting


Personally, the valve clearance (if nobody's been messing with it) would be last on my list of suspected causes.. Knowing diesel engines like I do, my very first suspect would be a dirty fuel filter.

Dec 03, 2013 | Cars & Trucks

2 Answers

2008 dodge ram 1500 loses power and has thick black smoke


do not use it!!! you will do more damage..
firstly, is the engine management light on?
if so you can try getting a diagnostics kit plugged into it. this will read all fault codes through the ecu.
if not you have a few things you need to check.
let me know

Jun 17, 2013 | Dodge Ram 50 Cars & Trucks

1 Answer

1997 jetta will start but wont stay runnig.


You have a problem with the EMU or a small electric valve which controls the idle speed of the engine

When you take your foot off it is supposed to hold the engine at say 700- 800rpm

The fuel input be it petrol or diesel is metered to the engine under the control of the EMU

Have you had the battery off recently, if so there is more than a chance that you have lost the settings for the idle speed and pain in the **** that it is, you need a man with a laptop to check it out and set it up

May 24, 2009 | 1997 Volkswagen Jetta

3 Answers

Volkswagen Diesel


according to haynes beetle repair the code is turbocharger boost pressure control valve positive deviation. to trouble shoot
check the wiring, connecting pipes.using a hand held vacuum pump apply vacuum to the wastegate actuator,(with engine not running) check the actuator arm and lever for freedom of movement , disconnect the electrical connector from the boost pressure control valve. using an ohmmeter check the solenoid windings for an open circuit, the boost pressure control valve should measure about 25 to 35 ohms if excessive resistance or open circuit is indicated replace control valve.
a scan tool is required for a complete diagnosis of the system control circuits some may be rented from a local auto repair store hope this helps and norrows it down for ya

Jun 16, 2008 | 2002 Volkswagen Beetle Turbo S

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...