Question about 1996 Chevrolet Impala SS

Open Question

P1886 timing solenoid - 1996 Chevrolet Impala SS

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show me where the shift timing solenoid located on a 2003 Chevy trailblazer


shift timing solenoid ????? There are 1-2 shift solenoids , 2-3 an 3-4 but no shift timing solenoids . An all solenoids are inside the transmission . Do yourself a favor an take your vehicle to a qualified repair shop .

Mar 22, 2017 | 2003 Chevrolet TrailBlazer

1 Answer

1996 Pontiac firebird v6 3.8L error code p1860 p1860pd p0306 p1460pd changed tcc pwm solenoid code still won't clear others only appear during a 100 mile drive cycle please help!!!


You replaced the TCC solenoid , but did you test the electrical circuit ? Code description - DTC P1860 TCC PWM Solenoid Circuit Electrical. - YOU SEE SOLENOID CIRCUIT ELECTRICAL - no where does it say to replace the solenoid . TEST THE ELECTRICL CIRCUIT ! P0306 should set right away if misfire is present . P0306 cylinder # 6 misfire !
The TCC PWM Solenoid Valve controls the fluid acting on the converter clutch valve, which then controls the application and release of the TCC. The solenoid attaches to the control valve body within the transmission. Circuit 439 supplies ignition voltage directly to the solenoid. The PCM controls the solenoid by providing a ground path on circuit 418. Current flows through the solenoid coil according to the duty cycle (percentage of ON and OFF time). The TCC PWM Solenoid Valve provides a smooth engagement of the torque converter clutch by operating during a duty cycle percent of ON time.
When the PCM detects a continuous open or a short to ground in the TCC PWM circuit or the TCC PWM Solenoid Valve, then DTC P1860 sets. DTC P1860 is a type A DTC.
Diagnostic Aids
?€¢
Inspect the wiring for any poor electrical connections at the PCM. Inspect the wiring at the transmission 20-way connector. Look for the following conditions:


-
A bent terminal


-
A backed out terminal


-
A damaged terminal


-
Poor terminal tension


-
A chafed wire


-
A broken wire inside the insulation


?€¢
When diagnosing for an intermittent short or an open condition, massage the wiring harness while watching the test equipment for a change



2

  1. Install the scan tool.
  2. With the engine OFF, turn the ignition switch to the RUN position.
  3. Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. The Clear Info function will erase the data.
  4. Record the DTC Freeze Frame and the DTC Failure Records.
Are DTCs P0753, P0758, P1860, P1864, or P1886 set?
--
Go to Step 3
Go to Step 4

3

Inspect circuit 439, the solenoid, the PCM IGN fuse, and the Automatic Transmission Wiring Harness for an open or a short to ground.
Refer to Electrical Diagnosis, Section 8.
Did you find and correct a problem?
--
Go to Step 17
--

4
  1. Turn the ignition switch to the OFF position.
  2. Disconnect the transmission 20-way connector (additional DTCs may set).
  3. Install the J 39775 Jumper Harness on the engine harness connector .
  4. With the engine OFF, turn the ignition switch to the RUN position.
  5. Connect a lest lamp from the J 39775 Jumper Harness connector cavity E to ground.
Does the test lamp illuminate?
--
Go to Step 6
Go to Step 5

5

Repair the open in the ignition feed circuit 439 to the TCC PWM Solenoid Valve. Refer to Electrical Diagnosis, Section 8.
Is the repair complete?
--
Go to Step 17
--

6
  1. Install the test lamp from cavities E to U of the J 39775 Jumper Harness connector .
  2. Using the scan tool, command the TCC PWM Solenoid Valve ON and OFF 3 times.
Does the test lamp illuminate when you command the TCC PWM Solenoid Valve ON, and turn OFF when you command the valve OFF?
--
Go to Step 8
Go to Step 7

7

  1. Inspect circuit 418 for an open.
  2. Inspect circuit 418 for a short to ground.
  3. Repair the circuit if necessary.
Refer to Electrical Diagnosis, Section 8.
Did you find and correct a problem?
--
Go to Step 17
Go to Step 9

8
  1. Install the J 39775 Jumper Harness on the Connector End View 20-way connector.
  2. Using the J 39200 DVOM and the J 35616-A Connector Test Adapter Kit, measure the resistance between terminals E and U.
Is the resistance within the specified range?
10-15ohms
Go to Step 11
Go to Step 10

9

Inspect the PCM connector terminals for the following conditions:
  1. Damaged connector pins
  2. Backed out connector pins
  3. Weak terminal tension
  4. Repair the connectors if necessary.
Did you find and correct a problem?
--
Go to Step 17
Go to Step 16

10

  1. Disconnect the Automatic Transmission Wiring Harness at the TCC PWM Solenoid Valve.
  2. Measure the resistance of the TCC PWM Solenoid Valve.
Is the resistance within the specified range?
10-15ohms
Go to Step 12
Go to Step 15

11

Using the J 39200 DVOM and the J 35616-A Connector Test Adapter kit, measure the resistance between terminal E of the J 39775 Jumper Harness and the transmission case (ground). Measure the resistance between terminal U of the J 39775 Jumper Harness and the transmission case (ground).
Are both readings greater than the specified value?
250ohms
Go to Diagnostic Aids
Go to Step 13

12

  1. Inspect the Automatic Transmission Wiring Harness for an open or short to ground.
  2. Repair the harness if necessary.
Refer to Electrical Diagnosis, Section 8.
Did you find and repair a problem?
--
Go to Step 17
--

13

  1. Disconnect the Automatic Transmission Wiring Harness at the TCC PWM Solenoid Valve.
  2. Measure the resistance between each of the component terminals and the transmission case (ground).
Are both readings greater than the specified value?
250ohms
Go to Step 14
Go to Step 15

14

  1. Inspect the Automatic Transmission Wiring Harness for a short to ground.
  2. Repair the harness if necessary.
Refer to Electrical Diagnosis, Section 8.
Was a problem found and corrected?
--
Go to Step 17
--

15

Replace the TCC PWM Solenoid Valve.
Refer to Torque Converter Clutch Pulse Width Modulation Solenoid Valve Replacement, in On-Vehicle Service.
Is the replacement complete?
--
Go to Step 17
--

16

Replace the PCM.
Refer to Powertrain Control Module Replacement/Programming , Section 6.
Is the replacement complete?
--
Go to Step 17
--

17

  1. After the repair is complete, select DTC.
  2. Select Clear Info.
  3. Ensure the following conditions:
  4. ?€¢
    When you command the TCC PWM Solenoid Valve ON, the voltage drops to zero.


    ?€¢
    When you command the TCC PWM Solenoid Valve OFF, the voltage increases to B+.


    ?€¢
    All conditions met for 5 seconds.

  5. Select Specific DTC and enter DTC P1860.
Has the test run and passed?
--
System OK
Begin diagnosis the again. Go to Step 1

Jun 28, 2016 | Pontiac Cars & Trucks

1 Answer

My 1996 Gmc Jimmy 4wheel drive was driving fine till one day i noticed the car was dragging,. well i noticed the gear shifter indicator not lit up showing what gear its in. Before i was able to turn key...


I would suggest you go to a competent trans shop that is trustworthy .They should be able to diagnose the problem . If you keep driving it like that you blow it up for sure. Good luck Bill (also ask for your money back)

Jan 06, 2015 | Cars & Trucks

1 Answer

Codes p1860 p1864 p1886 are showing up on my 1996 GMC sierra it has to be manually shifted then when put in park it get stuck and wont go back in gear the shifter will not move Also I replaced computer and...


Replacing the computer won't fix anything if there is sensors triggering a fault If you punch in google the code number (called an obd2 code) it will tell you what sensors are being triggered usually it will turn out a misfire or o2 sensor it will always trigger if the sensor is faulty as for the shifting i couldn't tell you check the codes on google

Apr 02, 2014 | Cars & Trucks

1 Answer

I have 96 chevy 1500 Z71 and the check eng light came on and is reading code P0758, P0753, P1886, and P1864 how can I fix this?


Check your plug-in connectors at the transmission and PCM. You can get free diagrams for the chassis at Autozone.com when you register your vehicle for free.

The following Codes are translated as 757-shift control solenoidA,753-shift control solenoidB,1886-shift timing solenoid,1864-Torque Converter Circuit.

I usually work on Ford type products, but looking at 4 codes can easily mean a common connector is corroded or loose. Look at the wiring Diagrams and you will probably see a connection that leads to all 4 of these parts.

Feb 18, 2012 | Cars & Trucks

1 Answer

1996 GMC Sonoma 4.3 SLE has a P1886 code showing what and where is the problem?


the code is 4x4 initialization error. which means if you have a 4x4 then the computer is not seeing it. or if you have a 2 wheel drive then the computer "glitched" and now it thinks it is a 4x4 . either way the computer will have to be "flashed" that is reprogrammed.

Nov 18, 2011 | 1996 GMC Sonoma

1 Answer

WHAT'S THE PROBLEM WHEN THIS CODE APPEARS: P1886?


what is the make and model of your vehicle?

Nov 18, 2011 | Cars & Trucks

Not finding what you are looking for?
1996 Chevrolet Impala SS Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...