Question about 2006 Ford Crown Victoria

Open Question

I have airbag code 33 in a crown victoria. please help

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 22 Answers

SOURCE: 2005 crown victoria airbag light

First you should check the plug in connections under both seats if they are pluged in then check crash sensor on front bumper behind grill good luck

Posted on Dec 15, 2008

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

reisdos
  • 1297 Answers

SOURCE: fuse diagram for 2000 crown victoria

there are 5+ pages of fuses what specifically do you need


Posted on Jul 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset the airbag light in a 2008 Ford Crown Victoria Police Interceptor?


Same as with any MIL Lamp or check light, you
get on your dash,you check for codes, to see if you have
a system fault,diagnose the fault & make the repairs required

Folks have to give up this stuff about resetting things

If ANY light stays light on your dash after the motor is running
or your driving-- you have problems

Clearing-- NOT-- resetting anything- is NOT- a fix for any vehicle issue

Sep 19, 2014 | 2008 Ford Crown Victoria

1 Answer

HOW DO I CLEAR THE AIRBAG CODES ON A 1992 CROWN VICTORIA


hi there, try the following link, i could explain it all but it is better if you can view the link with pictures etc to get a better understanding of what you are dealing with:

www.crownvic.net/ubbthreads/ubbthreads.php?ubb=showflat&number=2339714


hope this solves your problem

Sep 13, 2012 | 1992 Ford Crown Victoria

1 Answer

How do i clear the airbag codes on a 92 crown victoria


that is so easy, you just plus a obd2 code reader with the function of erase fault code to clean codes.
_____________
airbag reset tools

Sep 13, 2012 | 1992 Ford Crown Victoria

1 Answer

Hello, on my 2004er P70 Crown Victoria is the airbag light flashing. Code 19. What is the problem and what can i do ? Thank you


it needs a charge or actually recharge you replace the explosive canister and reset the computer but will cost you if you feel panic driving your car without airbag fix it if you dont no need to fix it lots of cars lacking the airbags and won`t kill you since you drive safely and put your seat belt

May 31, 2011 | Ford Crown Victoria Cars & Trucks

1 Answer

My husband's 97 Crown Vic's airbag light flashes a code 12 and then stays on steadily. He recently had a water leak in the back passenger side...and quite a bit of moisture was in the car....could this...


dont panic! air bag flashes with code 12 means the airbag module doesnt have power supply. may be it might be disconnect during any other vehicles work! thanks

Feb 07, 2011 | 1997 Ford Crown Victoria

1 Answer

Air bag light on dash board citroen picasso


Check the plugs and sockets under the seats, they tell the airbag system if there are occupants and if the readings are wrong to the airbag ecu it disables itself and lights the warning lamp, clean the plugs and sockets or sometimes I have soldered the wires to get decent contact (one at a time)

Aug 01, 2009 | 2003 Ford Crown Victoria

1 Answer

Airbag light on


Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.
Just push it together properly and it should clear the AirBag fault

Mar 26, 2009 | 1998 Ford Crown Victoria

1 Answer

Airbag light is on


Disconnect the battery for 5 minutes

Mar 18, 2009 | 2005 Ford Crown Victoria

1 Answer

2005 crown victoria airbag light


First you should check the plug in connections under both seats if they are pluged in then check crash sensor on front bumper behind grill good luck

Oct 16, 2008 | 2005 Ford Crown Victoria

Not finding what you are looking for?
2006 Ford Crown Victoria Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...