Question about Toyota Sequoia

Open Question

Remove Oil Pan

2008 Sequoia Lower pan, All Bolts Are Out. Do I Need To Remove The Two Studs Before Trying To Pry Pan Off? Thanks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: Replace Oil Pan on 1996 Volvo 850GL

Your motor mounts may inhibit jacking the engine far enough up to clear the oil pump so it may be necessary to loosen one or more. This is not a critical point so retightening them shouldn't cause any problems.

Posted on Jan 13, 2009

  • 51 Answers

SOURCE: oil pan removal on 2002 gmc sierra

did you pull the rubber plugs between the motor and trans out? there are either nuts or bolts up there

Posted on Mar 15, 2009

moparownr
  • 667 Answers

SOURCE: Need torque specs for oil pan bolts

torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

Posted on May 22, 2009

Molson02536
  • 3854 Answers

SOURCE: pontiac montana oil pan bolt diagram for removal

If all the bolts are off, then the gasket is holding the oil pan in place and your going to have to tap it with a mallet, Not a hammer but a mallet so you don not damage the oil pan. Good luck and hope this helps.

Posted on Jul 13, 2009

timsauto123
  • 750 Answers

SOURCE: I need to replace the oil pan gasket on my 2000

yes,remove those bolts as well,the way I always approach a job like that,which I've done hundreds is always better to take off more than not enough,just look around the oil pan and look at the gasket and see how many bolt holes it has,that should answer your question.









TIM............






Posted on Oct 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

1 Answer

How do I get oil pan off on a 2000 Saturn LW300 V6 3.0L


The official shop manual reads :
Remove nose cone brackets bolts from oil pan.
Remove lower transmission flange to oil pan bolts.
Remove oil pan bolts.
Using designated pry points to break loose the seal. Bump the pan with a rubber mallet to loosen the pan from the engine block.
Remove oil pan.
By the illustrations, the only thing in the way is the oil pickup tube.... Good luck !
t

Nov 21, 2014 | Saturn Cars & Trucks

1 Answer

How to replace a oil pan gasket 2004 nissan xterra


are you referring to the lower sub pan or main oil pan? the lower sub pan on most nissan engines are fairly easy to diy. just unbolt all the fastening bolts and you would need a pry bar or screwdriver to pry off pan. remove the old liquid gasket on pan and on main pan mating surface and reapply liquid gasket. reinstall lower sub pan and install fastening bolt.
if you are referring to the engines main oil pan its a more extensive repair. you would need the correct tools and equipment such as trans jack and engine support holder.

Oct 11, 2014 | Cars & Trucks

1 Answer

How to remove the oil pan on a 1996 honda accord


First you must remove the A exhaust pipe that is under the oil pan. Make sure use a penetrating lube, like WD-40 on all exhaust nuts. If there is a lot of rust, you can remove the 3 or 4 manifold nuts, the 2 bolts for the bracket to the block, and unhook the exhaust hangers, and move the whole exhaust out of the way. Drain the oil, then remove the support brackets, then all the 10mm oil pan bolts and nuts. The oil pan can seem glued in place, pry it loose without bending it. Make sure you get any steel rings off from around the studs, they are part of the oil pan gasket, and tend to stick to the block.

Oct 05, 2014 | 1996 Honda Accord

1 Answer

Removal of oil pan 2003 dodge stratus


To get the oil pan off of your 2003 Dodge Stratus 2.7L engine, you must remove the following:
> Engine oil dipstick and tube
> Engine oil filter
> Structural collar (metal plate that bolts on the bottom between the oil pan and transmission housing)
> Exhaust cross-under pipe
> Torque converter housing cover
> The lower bolt attaching the A/C compressor to the oil pan
> Oil pan fasteners, Oil pan and gasket
Please note that attempting to remove the exhaust cross-under pipe can be a real challenge if you do not have the equipment to heat the nuts/studs that fasten it to the manifolds.
Non-availability of the required equipment in this case may mean that you will have to remove the exhaust manifold(s) to drill out broken studs.

May 16, 2012 | 2002 Dodge Stratus

1 Answer

How do i remove 2008 cobalt oil pan?


  1. Raise and support the vehicle.
  2. Place a drain pan under the oil pan drain plug.
  3. Remove the oil pan drain plug.
  4. Drain the engine oil.
  5. Remove the engine belt
  6. Remove the lower AC compressor bolt.Remove the 4 oil pan to transaxle bolts (1).
  7. Remove the oil pan bolts.

Jun 17, 2011 | Chevrolet Cobalt Cars & Trucks

2 Answers

I need to replace the oil pan gasket on a 03 dodge ran 1500 2x4 with the 4.7 do I just unscrew it and take the gasket out put the new one in and screw it back together or is there more


Oil Pan - Removal & Installation3.7L, 4.7L And 5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Attach an engine crane.
  4. Loosen, but don-t remove, the left and right mount through-bolts.
  5. Remove or disconnect the following:
    Negative battery cable Structural cover Front crossmember
  6. Raise the engine just enough for clearance.
  7. Remove or disconnect the following:
    NOTE Don-t pry on the pan. The gasket is integral with the windage tray, and doesn-t come out with the pan.
    NOTE The double ended studs must be installed in their original locations.
    Pan bolts and studs Pan
To install:
  1. Install or connect the following:
    Oil pan gasket Oil pan. Tighten the bolts, in sequence, to 105 inch lbs. (12 Nm). Front crossmember Structural cover Negative battery cable
  2. Fill the crankcase to the proper level with engine oil.
  3. Start the engine and check for leaks.

    5e4dc6b.jpg
    Fig. Oil pan bolt torque sequence-3.7L engine


    82403a9.jpg
    Fig. Oil pan mounting bolt tightening sequence-4.7L engine


    f5a0196.jpg
    Fig. Oil pan alignment dowel placement-3.9L engine shown

Hope helped; TY for using Fixya (remember comment and rated this post).

Apr 14, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

How do you remove the oil pan on 2001 grand prix


Remove the motor mount bolts on both sides. Using a jack & wood block, jack the engine high enough to allow the pan clearance enough for removal. Use wood blocks(4 by 4) at motor mounts & lower engine mounts onto the blocks. Lower & remove jack & block at jack. Remove pan bolts & carefully using a large pry bar or common screwdriver pry the pan away from engine . Good luck!

Apr 01, 2010 | 2001 Pontiac Grand Prix

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

1 Answer

2003 oil pan removal


4.0L Engine To Remove:
  1. Disconnect negative battery cable.
  2. Lift the vehicle.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Exhaust pipe from exhaust manifold.
    • Exhaust hanger at the catalytic converter and lower the pipe.
    • Starter motor.
    • Flywheel/torque converter housing access cover.
    • Oil level sensor (if equipped).
  5. Place a pole jack under vibration dampener with a piece of wood between dampener and jack.
  6. Remove or disconnect the following:
    • Engine mount through bolts and raise engine for clearance to remove pan.
    • Transmission cooler lines (if equipped).
    • Oxygen sensor harness from oil pan mounting studs.
    • Oil pan bolts and studs.
    • Oil pan and gasket.
To Install:
  1. Clean the gasket mating surfaces.
  2. Apply Mopar® Silicone Adhesive Sealant or equivalent onto the cylinder block in four location as shown.
7605306.gif

  1. Attach the pan gasket to the oil pan with Hi-tack or equivalent (2003-2005 vheicles).
  2. Use 1 ½ x ¼ inch bolts to fabricate alignment dowels. Cut off the head of the bolts and cut a slot into the top of the dowels (2006 vehicles).
4e495fd.gif

  1. Install two dowels into the timing case cover (2006 vehicles).
  2. Install two dowels into the cylinder block (2006 vehicles).
  3. Place the gasket over the dowels and onto the cylinder block and timing case cover (2006 vehicles).
  4. Position the oil pan.
  5. Install the 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm).
  6. Install the 5/16 inch oil pan bolts. Tighten to 132 in-lb (15 Nm).
  7. Remove the dowels.
  8. Install the remaining 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm) (2006 vehicles).
  9. Lower the engine onto the engine mounts.
  10. Install the through bolts and tighten the nuts.
  11. Remove jack stand and remove the piece of wood.
  12. Install the flywheel and torque converter access cover.
  13. Install starter motor.
  14. Connect the exhaust pipe to the hanger and to exhaust manifold.
  15. Install the transmission oil cooling lines (if equipped).
  16. Install the oxygen sensor wiring supports to the oil pan mounting studs.
  17. Install the drain plug into the oil pan. Tighten to 25 ft-lb (34 Nm).
  18. Lower the vehicle.
  19. Connect negative battery cable.
  20. Fill the oil pan with oil. WARNING
    Use extreme caution when the engine is operating. Do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
  21. Start the engine and inspect for leaks.

Jun 06, 2009 | 2003 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...