Question about Ford Bronco

1 Answer

I have a 1990 bronco full size when i turn the lights on one is high and one is low if i hit lhe high beam switch they switch what is going on

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Hi there, first at all check for loose wires (black wire to ground) If all wires are in good shape, then verify the bulb is in good condition, if it's burned, I recomend to replace both bulbs by new ones, I hope It helps!

Posted on Nov 21, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 178 Answers

SOURCE: low beams

hello i no you said you checked your fuse box go under your hood drivers side near your strut tower their problay is a second fuse box its black some times fuses is on the cover you have to unlock the side of cover lift off on inside of cover will list what is what sometimes left and right headlamps are seperate fuses goodluck

Posted on Sep 14, 2008

  • 193 Answers

SOURCE: high beams wont turn on.

First place to start is with headlight switch. I did have a case many years ago when both high beams were blown out at once, but this is rare. When you have the headlight switch out, jump power from te low beams to the high beam contacts. If high beams come on, replace switch.
Bill

Posted on Nov 19, 2008

j_del
  • 1586 Answers

SOURCE: INOP low beam and high beams

The problem is the headlight switch itself - it's one of the most common failures on these cars. The part, brand-new, is about $158 from ECSTuning.com. Replacing it involves removing the airbag and steering wheel - not difficult but a little nerve-wracking due to the power of the airbag.

If this is something you want to tackle on your own, reply back here and I can give you a step-by-step on doing the work yourself. Or you can go to a shop/dealer and just have them do it. They'll probably charge you at least two hours' labor, even though it's a 40 minute job. Let me know what you would like to do.

Posted on Dec 11, 2008

  • 7353 Answers

SOURCE: low beams don't work - both out at the same time.

DID YOU CHECK THE BULBS?

Posted on Nov 04, 2009

Testimonial: "spot on."

  • 1244 Answers

SOURCE: 2001 Ford Focus - High beam / low beam problem with headlights

just replace the dimmer switch under the column its wore out on the low beam side

Posted on Jan 17, 2010

Testimonial: "It's great to know that there's not a whole lot more to check! I wouldn't have guessed I was so close. Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights wont turn


sounds like the headlight switch is defective and needs replacing,but you need to check to make sure the rod that the switch pushes against if make the full travel and not short as this will not allow the switch to change from low beam to high beam.if the rod is travelling the full length then the switch is no good.you should also hear a click when moving the arm to go from low to high if not then the switch is bad.by holding the lever at a certain position to get the high beams to work this also indicates a switch problem.

Nov 04, 2013 | Cars & Trucks

1 Answer

Does this model use a 4 headlight bright system? I have 2 low beam lights but when I put on the bright lights the 2 low beam lights go out and only the 2 bright lights stay on.


I think that many 1990s and even some 1980s GM vehicles with seemingly 4 headlight systems actually use only 2 at a time.

My 1990 Oldsmobile Cutlass Calais, for instance, had 2 high beams that went on independently of the 2 low beam lights when switched with the turn signal lever.

In the 1970s the GM vehicles had 4 headlight systems where all 4 headlights would go on, but they used sealed beams rather than the capsule lights that are used nowadays.

For instance, our 1976 Cadillac Seville has a 4 headlight system that lights up 4 headlights on the high beam mode.

Good luck on seeing at night with the current set up.

Dec 09, 2010 | 1992 GMC Sierra

1 Answer

I have a 1990 audi quattro V8, both low lights went out.. Marker lights and high beams both work


I would check the low beam fuses. Also maybe a bad dimmer switch. Check to see if you have power at the low beam headlight plug.

Mar 13, 2010 | 1990 Audi V8 Quattro

1 Answer

My high beams dont work.


high beam switch is faulty look at getting a new stalk.....

Aug 25, 2009 | 1990 Toyota Land Cruiser

1 Answer

I have a nissan pulsar Q 2001 model. When I turn on the lights the park lights come on but on switching to low beam the lights remain in park. High beam works fine. Where would the problem lie?


hi
the problem may be due to the mid spring inside the light switch which cause the turn on ,of the low beam light .its better to replace the light switch near the steering

Jul 14, 2009 | 1990 Nissan Pulsar

1 Answer

Dynasty headlights


it is ur switch that changes it from low beam to high beam
[ turn singnal switch]

Feb 15, 2009 | 1990 Dodge Dynasty

2 Answers

The headlights are stuck on high beam.


pull on the signal lever toward you (ceter position). the signal lever controls the head lights either high beam or low beam. if you pull on the signal lever toward you again, you will have high beam temporarily. and if you push the signal lever towards the front, you will have the high beam locked.

Jan 12, 2009 | 1990 Buick Regal

2 Answers

High beams wont turn on.


First place to start is with headlight switch. I did have a case many years ago when both high beams were blown out at once, but this is rare. When you have the headlight switch out, jump power from te low beams to the high beam contacts. If high beams come on, replace switch.
Bill

Nov 19, 2008 | 2004 Ford Explorer Sport Trac

1 Answer

Haed lights


All 4 lights is HIGH beam. The 2 that come on in 'LOW' are the low beams.

Sep 03, 2008 | 1990 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...